Specifications

w w w. a u to m a t i o n d i r e c t . c o m / C - m o r e - m i c r o
Operator Interface
e11-53
Company
I
nformation
S
ystems
Overview
Programmable
Controllers
F
ield I/O
Software
C
-more &
other HMI
Drives
S
oft
Starters
Motors &
G
earbox
Steppers/
S
ervos
M
otor
Controls
Proximity
Sensors
Photo
Sensors
Limit
Switches
Encoders
Current
Sensors
Pressure
Sensors
Temperature
Sensors
Pushbuttons/
Lights
Process
Relays/
Timers
Comm.
Terminal
Blocks &
Wiring
Power
Circuit
Protection
Enclosures
Tools
Pneumatics
Safety
Appendix
Product
Index
Part #
Index
Volume 14
*NOTE: When the 6” panel is powered through Port1 from a connected PLC or PC, the screen brightness is diminished because the
panel is running in Low-Power Mode. For full brightness, connect an external Class 2, 12-24 VDC power source to the 6” panel’s
power connection. Low-Power Mode should be used during initial programming only. Connect an external Class 2, 12-24 VDC power
source when the panel is installed in its application.
Specifications
EA1-S6ML and EA1-S6MLW
Electrical
Low Power Mode* High Power Mode
• Input Voltage Range
5.0 VDC (4.75 – 5.25 VDC) 12/24 VDC (10.2 – 26.4 VDC)
• Input Power
Supplied through the panel’s RJ12 serial communications port con-
nection when used with most AutomationDirect PLCs having a RJ12
c
ommunication port or from a PC USB.
Supplied from an external Class 2, 12-24 VDC power source
• Power Consumption
1.05 W (220 mA@4.75 VDC) 6.5 W (640 mA @ 10.2 VDC)
• Recommended Fuse
N
o fuse required when directly connected to a PLC or PC with
recommended cable.
T
ype AGC fast acting glass fuse,
750 mA, 250 VAC, ADC p/n AGC-75
• Maximum Inrush Current
1 A for 500 µs 10 A for 500 µs
• Acceptable External
Power Drop Duration
Maximum 1 ms
Specifications
EA1-T6CL
Electrical
USB Bus Power (Programming only)* High Power Mode
• Input Voltage Range
5.0 VDC (4.75 – 5.25 VDC) 12/24 VDC (10.2 – 26.4 VDC)
• Input Power
Supplied from a PC USB. Supplied from an external Class 2, 12-24 VDC power source
• Power Consumption
2 W (420 mA @ 4.75 VDC) 6.5 W (640 mA @ 10.2 VDC)
• Recommended Fuse
No fuse required when directly connected to a PLC or PC with
recommended cable.
Type AGC fast acting glass fuse,
750 mA, 250 VAC, ADC p/n AGC-75
• Maximum Inrush Current
4.5 A for 800 µs 13 A for 800 µs
• Acceptable External
Power Drop Duration
Maximum 1 ms
*NOTE: The EA1-T6CL can be powered through Port1 when connected to a PC for programming, the screen brightness is diminished
because the panel is running in Low-Power Mode. For full brightness, connect an external Class 2, 12-24 VDC power source to the
6” panel’s power connection. An external Class 2, 12-24 VDC power source must be used when the panel is installed in its
application.
C-more 6” Micro-Graphic Specifications
*NOTE: EA1-T6CL cannot be powered by a PLC and cannot
communicate with a PLC through Port1
For a list of supported protocols and cabling options refer
to the 4” & 6” C-more Micro-Graphic Protocols and
cabling chart starting on page 11-61.
PLC Drivers
Serial - port1 or port2 Serial - port2 only
AutomationDirect Productivity Series Allen-Bradley DF1 Half Duplex
AutomationDirect Do-more Allen-Bradley DF1 Full Duplex
AutomationDirect CLICK Allen-Bradley PLC5 DF1
AutomationDirect K-sequence Allen-Bradley DH485
AutomationDirect DirectNET GE SNPX (90/30, 90/70, Micro 90, VersaMax Micro)
AutomationDirect Modbus Mitsubishi FX
Modicon Modbus RTU Mitsubishi Q & QnA
Entivity Modbus RTU Omron Host Link (C200 Adapter, C500)
Omron FINS Serial (CJ1, CS1)
Siemens PPI (S7-200 CPU)
AutomationDirect SOLO Temperature Controller
AutomationDirect GS Drives