Installation manual

ManualsBrandsC&K systems ManualsComputer equipmentSystem 236i

SYSTEM 236 Installation Manual

5-051-191-00 Rev F

Connect ground wire from door hinge to earth ground

using 16 AWG, green jacketed, solid-conductor wire

•

GENERAL INFORMATION

All outputs are power limited

•

If programmed for EOL or Supervised Loop, the 2.2K

ohm EOL resistor (Model 9.X, 2.2K) must be at end of

circuit

•

When used as a fire warning system, use a 4-wire

smoke detector (Sentrol #ES-449C) with a Power

Supervisory EOL Relay Module (System Sensor A77-

716 Series) at the end of the detector power loop.

Consider the maximum detector alarm load when

confirming that the total alarm load is less than 800

mA.

•

are electrically common

•

Loop voltages: 0.00 - 1.50 VDC = short

1.60 - 3.10 VDC = normal

3.20 - 5.00 VDC = open

•

16.5 VAC

25 - 40 VA

50 or 60 Hz

AUDIBLE

9.5 - 14 VDC

Protected by

Fuse F1:

3AG, 1.0 A

SWITCHED

AUX

POWER

9.3-14.0 VDC

KEYPAD

Do not exceed 3 keypads

Protected by Fuse F2:

3AG, 0.5 A

Capacity for

emergency standby

at least four hours

CAUTION:

Total Power from terminals

BELL, AUX, and KEY+ NOT

to exceed 800 mA, combined.

(Also see NOTE: below.)

Direct

Conn

JP2

Watch

Dog

DS1

WARNING:

For continued protection against risk of fire, replace

fuses only with fuses of same type and rating.

Disconnect AC, battery, and phone cord BEFORE

servicing.

PHONE CORD 9.X PCF

Red = Incoming Ring (R)

Green = Incoming Tip (T)

Grey = Seized Ring (R1)

Brown = Seized Tip (T1)

Blue = Tamper

Orange = Tamper

Slow Blow

POWER SUPPLY INFORMATION

Use only 12 VDC, 6.5 A-H or 4.0 A-H sealed lead-acid battery

Replace battery every 4 - 6 years with C&K Model 1265 or Model 1240

6.5 A-H standby battery time with 1 keypad is 14 hours at 300 mA

Power demand for AUX POWER, keypads, and sounders not to

exceed maximum ratings.

Install transformer on unswitched power receptacle

Maximum battery charge current = 350 mA

This equipment should be installed in accordance with the

National Fire Protection Association's Standard 72 Chapter 2

(National Fire Protection Association, Batterymarch Park, Quincy,

MA 02269). Printed information describing proper installation,

operation, testing maintenance, evacuation planning and repair

service is to be provided with the equipment.

4.0 A-H standby battery time with 1 keypad is 7 hours at 400 mA

NOTE:

Total power from terminals AUX and KEY+

NOT to exceed 400 mA, combined.

All ratings on this page are in compliance with UL 985,

UL 1023, and UL 1635.

12 VDC, 6.5 A-H

12 VDC, 4.0 A-H

Sealed Lead-acid

Summary of content (28 pages)

PAGE 1
SYSTEM 236 Installation Manual Direct Conn Watch Dog DS1 JP2 WARNING: For continued protection against risk of fire, replace fuses only with fuses of same type and rating. Disconnect AC, battery, and phone cord BEFORE PHONE CORD 9.X PCF servicing. Red = Incoming Ring (R) Slow Blow Green = Incoming Tip (T) Grey = Seized Ring (R1) Brown = Seized Tip (T1) Blue = Tamper Orange = Tamper Capacity for emergency standby at least four hours 16.5 VAC 25 - 40 VA 50 or 60 Hz GENERAL INFORMATION AUDIBLE 9.
PAGE 2
SYSTEM 236 Installation Manual UL Compliance(continued) Table of Contents Subject System 236 Terminal Label UL Compliance Installation Wiring the Panel System Start-Up Keypad Setup Addressing Keypads Factory Default Settings Programming Options (Alphabetical List) Programming the Panel Programming with the LED Keypad Programming with the Alpha Keypad Entering Hexidecimal Numbers Programming the Alpha Keypad Programming Letters & Numbers Special Function Keys Programming Options (Numerical Order) Keypad Lab
PAGE 3
SYSTEM 236 Installation Manual Electromagnetic Interference Vibrating horns can produce electromagnetic interference (EMI). While EMI will not damage the SYSTEM 236, it can cause transmission errors and mis-dialing. To minimize EMI, install a 0.01 mfd, 100 V capacitor across the terminals of the horn. The capacitor must be located in the horn. WIRING THE PANEL STANDBY BATTERY The SYSTEM 236 is designed to operate using a 12 V, 6.5 A-H (Model 1265) or 12 V, 4.0 A-H (Model 1240) sealed lead-acid battery.
PAGE 4
SYSTEM 236 Installation Manual Supervised Loop + N.C. Trouble N.O. Alarm - 9.X PCF The 9.X PCF has eight flying leads on one end. When operated as a Supervised Loop, an open will be reported as a Trouble, whether the system is armed or disarmed. A short on a Supervised Loop will be reported as an alarm if the system is armed, but will have no effect if the system is disarmed.
PAGE 5
SYSTEM 236 Installation Manual Combinations (cont.) Combination required: no Faulted Arming type: goof-proof Opening/closing: no Users authorized to send O/C reports Adjusting the LCD Display To adjust the viewing angle, remove the keypad from the back mounting plate. Towards the bottom center of the circuit board is a small hole. Insert a small screwdriver into the hole and adjustR23, while holding the keypad at its mounting height. Adjust the potentiometer as necessary for optimum viewing.
PAGE 6
SYSTEM 236 Installation Manual Option Location Failed To Communicate Report Code Faulted Arming Type Installer Combination Keypad RPS Enable Local System Only Loop Alarm Report Code Loop Arming Type Loop Audible Type Loop Circuit Type Loop Receiver Select Loop Response Time Loop Restore Reporting Code Loop Restore Type Loop Shunting Enable Loop Shunt Report Code Low Battery Report Code Low Battery Restore Report Code Master Code Opening Report Code Opening/Closing Report Receiver Select Panic Audible Typ
PAGE 7
SYSTEM 236 Installation Manual Data is programmed into the panel using the hexidecimal number system, which consists of the digits 0 - 9 and the letters A - F. The digits 0 - 9 are entered directly from the keypad. The chart below shows how to enter the hexidecimal digits A through F. The Scrolling order of the Alpha II messages is: SERVICE MESSAGE DEALER MESSAGE SOFT ZONE IDENTIFIER (C) HARDWIRED LOOP IDENTIFIERS KEYPAD ADDRESS . . . . .
PAGE 8
SYSTEM 236 Installation Manual SPECIAL FUNCTION KEYS MOVE CURSOR LEFT ( The Alpha II keypad also has special function keys available during programming. The function of each key is outlined below: ) A combination of the STAR (*) and the POLICE + P (P) key is used to move the cursor one space to the left. The data which is passed over is not changed. This key may be shown with the symbol on some keypads. * STAR (Shift) * allows you to shift the 1, 2, 3, 4, 5, andkey0 keys to other values or functions.
PAGE 9
CL 00 - 07 SYSTEM 236 Installation Manual Command Location 00: Installer Combination Default Values 0 1 2 3 4 5 # 0 0 (1) (2) (3) (4) (5) (6) Digit Positions (1) - (6): Installer Combination Combination must have 6 digits. Valid entries are 0 - 9.
PAGE 10
SYSTEM 236 Installation Manual CL 08 and 09 Command Location 08: Panel Control Options Default Values 0 0 1 0 0 1 # 0 8 (1) (2) (3) (4) (5) (6) Digit Position (1): Disable Loop LEDs 0 = No 1 = Yes: shuts zone LEDs off after 5 minutes Digit Position (2): Faulted Arming Type 0 = Goof-proof: zones must be normal or shunted to arm 1 = Force Arm: faulted zones will be shunted at end of Exit Delay Digit Position (3): Default Installer Combination 0 = No; this enables the Pirate-GuardTM feature for
PAGE 11
SYSTEM 236 Installation Manual CL 0A and 0B Command Location 0A: Communications Format Default Values 1 1 (1) (2) 0 0 1 1 # 0 A (3) (4) Digit Position (1): Receiver #1 Receiver Format 1 = Fast "A", 2300 Hz 2 = Slow "B", 1400 Hz 3 = SumCheck, 1400 Hz 4 = SumCheck, 2300 Hz 5 = CFSK III 6 = Ademco DTMF, 1400 Hz Digit Position (2): Receiver #1 Message Format 1 = 3/1 Extended 2 = 4/2 (2-digit reporting code) 3 = CFSK III Digit Position (3): Receiver #2 Receiver Format 1 = Fast "A", 2300 Hz 2 = Slo
PAGE 12
SYSTEM 236 Installation Manual CL 0C - 0E Command Locations 0C - 0E: Receiver #1 Phone Number Order in which the numbers will be dialed Command Location 0C (1) (2) (3) (4) (5) Command Location 0D (6) (1) (2) (3) (4) (5) Command Location 0E (6) (1) (2) (3) (4) (5) (6) Command Location 0C: Receiver #1 Phone Number (digits 1 - 6) Default Values E 0 0 0 0 0 # 0 C (1) (2) (3) (4) (5) (6) Digit Positions (1) - (6): Receiver #1 Phone Number (Digits 1 - 6) 0 - 9 = dialing digits 0
PAGE 13
CL 0F - 11 SYSTEM 236 Installation Manual Command Locations 0F - 11: Receiver #2 Phone Number Order in which the numbers will be dialed Command Location 0F (1) (2) (3) (4) (5) Command Location 10 (6) (1) (2) (3) (4) (5) Command Location 11 (6) (1) (2) (3) (4) (5) (6) Command Location 0F: Receiver #2 Phone Number (digits 1 - 6) Default Values E 0 0 0 0 0 # 0 F (1) (2) (3) (4) (5) (6) Digit Positions (1) - (6): Receiver #2 Phone Number (Digits 1 - 6) 0 - 9 = dialing digits 0
PAGE 14
SYSTEM 236 Installation Manual CL 12 - 14 Command Locations 12 - 14: RPS Phone Number Order in which the numbers will be dialed Command Location 12 (1) (2) (3) (4) (5) Command Location 13 (6) (1) (2) (3) (4) (5) Command Location 14 (6) (1) (2) (3) 0 0 (4) (5) (6) Command Location 12: RPS Phone Number (digits 1 - 6) Default Values E 0 0 0 # 1 2 (1) (2) (3) (4) (5) (6) Digit Positions (1) - (6): RPS Phone Number (Digits 1 - 6) 0 - 9 = dialing digits 0 = dial tone detect (use
PAGE 15
SYSTEM 236 Installation Manual CL 15 and 16 Command Location 15: Event Reports Default Values 1 9 D F E 1 5 (1) (2) (3) # (4) (5) Digit Position (1): Event Report Receiver Select Shunts, All Restores, Status, Trouble, and Cancel 2 = Receiver 2 only 3 = Receiver 1 and Receiver 2 (Dual Reporting) 0 = Receiver 1 with Receiver 2 as back-up 1 = Receiver 1 only Digit Position (2): Loop Shunt Report Code Valid entries are 1 - F. This is a 1-digit reporting code used for all loops.
PAGE 16
SYSTEM 236 Installation Manual CL 17 and 18 Command Location 17: Status Events Reporting Codes - #1 Default Values 0 0 (1) (2) 0 0 # 1 7 (3) (4) Digit Position (1): Unit Status Report Code This is a global command for CL 17 and CL 18. If Position (1) is programmed with a "0", all Status Reports in CL 17 and CL 18 will be disabled. If Position (1) is programmed with any value other than 0, all Status Reports in CL 17 and CL 18 which have been enabled (not programmed with 0) will send reports.
PAGE 17
SYSTEM 236 Installation Manual CL 19 and 1A Command Location 19: Panic Report Default Values 0 0 1 1 # 1 9 (1) (2) 0 0 (1) (2) (3) (4) Digit Positions (1) - (2): Panic Report Code Valid entries are 0 - F Program a "00" to disable Panic Reports.
PAGE 18
SYSTEM 236 Installation Manual CL 1B and 1C Command Location 1B: Panel Timing Default Values 3 2 2 1 0 0 # 1 B (1) (2) (3) (4) (5) (6) Digit Position (1): Entry Delay 1 = 10 seconds 2 = 30 seconds 3 = 60 seconds 4 = 90 seconds 5 = 120 seconds 6 = 150 seconds Digit Position (2): Exit Delay 1 = 10 seconds 2 = 30 seconds 3 = 60 seconds 4 = 90 seconds 5 = 120 seconds 6 = 150 seconds Digit Position (3): Audible Time 1 = 2 minutes 2 = 5 minutes 3 = 10 minutes 4 = 15 minutes 5 = 30 minutes D
PAGE 19
SYSTEM 236 Installation Manual CL 1D - 23 Command Locations 1D - 22: Loop Control 1D = Loop 1 1E = Loop 2 1F = Loop 3 20 = Loop 4 21 = Loop 5 22 = Loop 6 Default Values 1 1 1 2 2 0 # 1 D Digit Position (1): Loop Response Time (1) (2) (3) (4) (5) (6) 0 = 10 milliseconds 1 = 500 milliseconds Digit Position (2): Loop Receiver Select 0 = Receiver 1 with Receiver 2 as back-up 1 = Receiver 1 only 2 = Receiver 2 only 3 = Receiver 1 and Receiver 2 (Dual Reporting) Digit Position (3): Loop Restor
PAGE 20
SYSTEM 236 Installation Manual CL 24 - 25 and A0 Command Location 24: Shunting Enable Default Values 1 1 1 1 1 1 2 4 (1) Digit Position (1): Loop 1 Shunting Enable (2) (3) (4) # (5) (6) 0 = No: makes this zone a priority zone (not shuntable) 1 = Yes: authorized users can bypass or force arm Digit Position (2): Loop 2 Shunting Enable Refer to Digit Position (1) for programming options. Digit Position (3): Loop 3 Shunting Enable Refer to Digit Position (1) for programming options.
PAGE 21
SYSTEM 236 Installation Manual FCC NOTICE TESTING Once the installation is complete, connect AC and DC power. Complete programming, if required. Test all panel operations. TO THE INSTALLER Regular maintenance and inspection (at least monthly) by the installer, and frequent testing by the user, are vital to the continuous and satisfying operation of any alarm system.
PAGE 22
SYSTEM 236 Installation Manual Keypad Operation Command Summary The majority of the keypad commands apply equally to the LED and Alpha II keypads. Some keypad commands, however, apply to the LCD keypad only.
PAGE 23
SYSTEM 236 Installation Manual Survey of Most Common Questions The following is a summary of the questions most frequently asked of our Technical Support Department. QUESTION: How do I program the panel with the LED keypad? ANSWER: To program with the LED keypad, enter the Command Location to be programmed, the Data to be programmed and the press the [#] key. (See also page 6.
PAGE 24
SYSTEM 236 Installation Manual Question: Answer: How do I interpret the Unit Status Reports? Can the codes be changed? Status Reporting is divided between CL 17 and CL 18. Each Reporting Code of the Unit Status Report is a two-digit code. The first digit is the data programmed into CL 17 Digit Position (1) and may be any value from 0 - F. The second digit is the data programmed into the respective Status Report Code.
PAGE 25
SYSTEM 236 Installation Manual Recommendations for Reducing False Alarms The recommendations contained in this section are designed to assist you in reducing false alarms. The first column contains the Command Locations and Digit Positions in parentheses ( ). The second column is the recommended program option followed by a brief explanation.
PAGE 26
SYSTEM 236 Installation Manual THE LIMITATIONS OF YOUR ALARM SYSTEM While the SYSTEM 236 is an advanced design security system, it does not offer guaranteed protection against burglary, fire, or other losses. Any alarm system, whether commercial or residential, is subject to compromise or failure-to-warn for a variety of reasons. These include: . . . . .
PAGE 27
SYSTEM 236 Installation Manual 236 Programming Worksheet Client: SYSTEM 236 Phone Number: Address: Installer: Date: CONTROL LOCATION: VOLTS AC volts (AC terms): KEYPADS Address AUX POWER VOLTS (terms AUX+ and C): Location 0 1 BATTERY VOLTS Under load - AC off: 2 BREAKER # AND LOCATION: 3 CURRENT Keypads 4 5 AUX POWER 6 + 7 TOTAL (400 mA allowed): 0 0 0 1 0 3 0 5 0 7 0 9 = 0 1 2 3 1 2 3 4 0 0 0 1 0 0 0 1 0 0 0 1 0 4 5 # Installer Combination 0 # User
PAGE 28
SYSTEM 236 Installation Manual 0 0 0 0 0 0 0 # B Account Number Phone #1 (1st 6 digits) E 0 0 0 0 0 (Middle 6 digits) 0 0 # C 0 0 0 0 0 0 0 # 1 1 0 0 0 1 5 1 7 1 9 1 B 0 0 3 1 1 D 1 F 2 1 2 3 2 5 1 1 0 0 9 0 0 2 1 1 1 0 0 D 0 1 2 1 1 1 0 0 F 0 1 1 2 0 0 0 0 E 0 0 0 0 # # 1 0 0 0 1 Panic/Duress 1 A 1 C 0 0 0 0 0 0 0 # Timing/Keypad Control # Loop 1 Control 1 E # Loop 3 Control 2 0 # Loop 5