Installation Manual

 b. Re-installregulatorondriveendhousingand
 torquemountingscrewsto8.5Nm/75lb.in.
2. Installalternator:
a. Carefullyplacealternatoronalternator 
 mountingbracket.
   Usecautionwhenliftingalternator
   topreventpossibleminorpersonal
   injury.Usehoistalongwithalterna-
   torliftingringlocatedontopof
   alternator.
 b. Securealternatortoalternatormounting
 bracketusingfour1/2-13,grade5orhigher
 mountingboltswithlockwashers.Mounting
 boltsshouldextend17.8/25.4mm(0.7/1.0in.)
 intoalternatormountingrail.Torquemounting
 boltsto88Nm/65lb.ft.
3. Unitsareshippedwithpulleyandhardwarealready
assembled.Installalternatordrivebeltandsecure
belttensionbracketassembly.Loopalternatordrive
beltoverpulleysandalignbeltwithpolyveegrooves.
II71E
Page 1 of 2
C701/C701A and C703/C703A
Alternators
OEM Installation Instructions
  Thissymbolisusedtoindicatethe 
  presenceofhazardsthatcancause 
  minorpersonalinjuryorpropertydamage.
CAUTION
1. A2-213,A2-214,andA2-325regulatorsare
flat-temperaturecompensatedandfactory-setat
lowestsettingtoaccommodate8Dbatteries.For
otherbatteries:
a. Removeregulatorfromhousingandchange
 positiononvoltageselectorswitch.SeeTable1.
CAUTION
Figure 1 - C701/C701A/C703/C703A Alternator Installation Details
* Use this setpoint to maintain proper battery charge level during
shorter operating cycles.
B+ terminal –
see inset above

C701/C701A: B– terminal 3/8-16
bolt – torque to 15 Nm/11 lb. ft.
C703/C703A: B– terminal M10
bolt – torque to 15 Nm/11 lb. ft.


A2-214/A2-325: D+ terminal 1/4-20 nut – torque to 3.4 Nm/30 lb. in.
A2-213: D+ terminal M6 nut – torque to 4.5 Nm/40 lb. in.

A2-214/A2-325: IGN terminal #10-24 nut – torque to 3.4 Nm/30 lb. in.
A2-213: IGN terminal M5 nut – torque to 4.5 Nm/40 lb. in.
C701/C701A: 3/4-16 nut – torque to 163 Nm/120 lb. ft.
C703/C703A: M20 x 1.5 mm ange nut – torque to
163 Nm/120 lb. ft.

C701/C701A: Hardened at washer
C703/C703A: Belleville washer

C701/C701A: 1/2-13 bolt – torque to 30 Nm/22 lb. ft.
C703/C703A: M12 bolt – torque to 30 Nm/22 lb. ft.
Flat washer
Battery output
cable terminal
Lock washer
Insulator





Cable clamp


Alternator lifting ring
A2-214/A2-325: P terminal 1/4-20 nut –
torque to 3.4 Nm/30 lb. in.
A2-213: P terminal M6 nut –
torque to 4.5 Nm/40 lb. in.

If an extended wiring harness is supplied with
alternator and regulator, see separate instructions
packed with harness.
Table1–RegulatorVoltageSelectorSwitchPosition
Position BatteryType
1 27.5V Maintenance
2 28.0V Maintenance*
3 28.5V Maintenance-Free
4 29.0V Maintenance-Free*
  Thissymbolisusedtoindicatethepresence
  ofhazardsthatcancauseseverepersonal
  injuryorsubstantialpropertydamage.
WARNING