Specifications

34
7540 Highway 64 West Brasstown, NC 28902 [phone] [phone]
fax: [phone] email: [e-mail] web: www.grove-ent.com
Technical Questions? [phone] or [e-mail]. Due to high call volume, technical calls will be limited to 3 minutes.
GROVE [phone]
Order ANT19
Our Price:
$
84
95
MFJ 1020C ACTIVE SHORTWAVE ANTENNA
If you can’t use an outdoor shortwave antenna, the popular MFJ 1020C is the way
to go. Featuring 300 kHz-40 MHz frequency-selectable coverage, and including its
own 20-inch telescopic whip, the 1020C may be used as a preselector for outdoor
antennas as well. Controls include gain, band, tuning, and bypass. Rear-panel SO-239
connectors are provided. Only 6-1/2”W x 2-1/2”H, the 1020C operates either from
an internal 9V battery (not supplied) or an optional 9-12 VDC AC adaptor; a red LED
lets you know the unit is on.
Suggested Accessories:
PWR04 - AC Adaptor ...................................... $14.95
CBL11 - 3’ PL-259/PL-259 Interconnect Cable . $3.99
WiNRADiO WR-LWA-0130 Long Wire Antenna Adapter
Often referred to as Long Wire Balun, this device is used to match the impedance of a long wire HF antenna to a 50
ohm input impedance of a receiver. Such impedance matching usually results in a
significant signal strength increase (up to 17dB in some cases, and approximately 5dB
on average), compared to the long wire antenna connected directly to the antenna
input of the receiver.
The WiNRADiO WR-LWA-0130 Long Wire Antenna Adapter is designed to work on medium and
short wave bands, covering a frequency range from 0.1 to 30 MHz. It is especially
suitable for use with WiNRADiO shortwave receivers, such as the WR-G303i receiver.
Unlike most conventional antenna adapters, the WiNRADiO WR-LWA-0130 Long Wire Antenna Adapter employs
a dual broadband transformer technique which offers an improved performance over single-transformer devices.
Requires BNC adaptor/connector.
Order ADP35 - Our Price:
$
39
95
HF INDOOR ANTENNAS
PAR HIGH-PERFORMANCE “END FEDZ” SHORTWAVE ANTENNA!
The PAR End Fedz 45-foot, commercial-quality, end-fed receiving antenna is made of virtually-indestructible
Flex Weave, covered by a protective black polyethylene jacket. Impedance-matched by a 9:1, binocular-core
transformer in a weather- and UV-resistant ABS housing, the wire element is firmly attached by stainless steel
hardware. You may custom-configure the shorting bar for grounding the
antenna. A silver/Teflon SO-239 coax connector is ready to receive the PL-
259 on your coax cable.
Mount this beauty outdoors, in the attic, or any other preferred spot for
unsurpassed, 1-55 MHz reception! Instructions include patterns for horizontal
or slope mounting.
Order ANT08 - Our Price:
$
59
95
CBL50 50’ - F to F RG6U cable ... $19.95
CBL100 100’ - F to F RG6U cable $24.95
ADP02 - F to PL259 adaptor ........ $3.00
Grove Skywire
High performance and low cost—an unbeatable combination! Why restrict your
frequency coverage with the gaps found in expensive trap dipoles or unpredictable
random wire when you can get unsurpassed full-frequency reception with the Grove
Skywire?
Comes assembled with Budwig center connector ready for your PL-259 (UHF
male) equipped coaxial cable (50 or 75 ohm); includes two professional porcelain
end insulators and complete instructions.
HAMS! Ideal for transmitting when used with a transmatch. (1.8-30 MHz at up to 250 watts)
Specifications:
Length: 66 feet
Feedpoint impedance: 50 or 75 ohm (nominal)
Feedpoint location: 22 feet from end for harmonic match
Elements: 18 AWG (16 x 30) bare stranded copper
Order ANT02
Our Price:
$
29
95
CBL50 50’ - F to F RG6U cable ...... $19.95
CBL100 100’ - F to F RG6U cable .. $24.95