User guide

ManualsBrandsBVA Hydraulics ManualsEquipmentIEPR5513, IEPRS5513, IAPDR5506, IEPDR5513, IEPDRS5513

Printed in USA

IAP5506-M0_092013

Max. Operating Pressure 10,000 PSI

Rolling Head Shop Press

Instruction Manual

MODELS: IMPR5506, IAPR5506, IEPR5506, IEPRS5506, IAPR5513, IEPR5513,

IEPRS5513, IAPDR5506, IEPDR5513, IEPDRS5513

SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153

Tel: 888-332-6419 * Fax: 816-891-6599

E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Summary of content (8 pages)

PAGE 1
IAP5506-M0_092013 Rolling Head Shop Press Instruction Manual MODELS: IMPR5506, IAPR5506, IEPR5506, IEPRS5506, IAPR5513, IEPR5513, IEPRS5513, IAPDR5506, IEPDR5513, IEPDRS5513 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 * Fax: 816-891-6599 E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com Max. Operating Pressure 10,000 PSI ! This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
PAGE 2
SAFETY AND GENERAL INFORMATION Save these instructions. For your safety, read, understand, and follow the information provided with and on this device before using. The owner and/or operator shall have an understanding of the device, its operating characteristics and safety operating instructions before operating the equipment. The owner and/or operator shall be aware that use and repair of this product may require special skills and knowledge.
PAGE 3
SPECIFICATIONS Press Model Rated Capacity Cylinder Model Pump Model/Type IMPR5506 Press Bed Depth (front to back) Press Bed Width (side to side) Press Size (H” x W” x L”) Min. Height (in.) Max. Height (in.) 14-7/8” 35-1/2” 79-1/8 x 56 x 30 14 55-1/2 Collar Thread (in.) Collar Thread Length (in.
PAGE 4
Pendant Switch Cylinder Pressure Gauge Bed Frame Upright Channel Electric Pump Winch Assembly Electric Pump Platform Air Pump Support Pin Air Pump Lower Cross Member Base Frame Channel Hand/Manual Pump Figure 1 - Components for 55-Ton Rolling Head Shop Press. BEFORE USE 1. Before using this product, read the operator’s manual completely and familiarize yourself thoroughly with the product, its components and recognize the potential hazards associated with its use. 2. Inspect before each use.
PAGE 5
8. Place pump on pump bracket and connect other end of hydraulic hose to cylinder. 9. Apply load to workpiece - do not overload. 10. Stabilize workpiece so that it will not inadvertently fall from bed frame once load is removed. 11. Once cylinder has fully retracted, remove workpiece. Reposition cylinder carriage only after cylinder has been retracted. NOTICE: To protect your cylinder, cease pump operation after cylinder ram is fully extended or retracted.
PAGE 6
Rolling Head Shop Press Service Parts MODELS: IMPR5506, IAPR5506, IEPR5506, IEPRS5506, IAPR5513, IEPR5513, IEPRS5513, IAPDR5506, IEPDR5513, IEPDRS5513 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 * Fax: 816-891-6599 E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.
PAGE 7
Rolling Head Shop Press Service Parts MODELS: IMPR5506, IAPR5506, IEPR5506, IEPRS5506, IAPR5513, IEPR5513, IEPRS5513, IAPDR5506, IEPDR5513, IEPDRS5513 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 * Fax: 816-891-6599 E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com Parts List Replacement Parts for 55-Ton Rolling Head Shop Press Item Part No.
PAGE 8
TROUBLESHOOTING A system failure may or may not be the result of a pump malfunction. The following information is intended to be used as an aid in determining if a problem exist.