BURR KING MFG. CO., INC 1220 Tamara Lane Warsaw, MO 65355 www.burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE www.burrking.com WARSAW, MO 65355 (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 June, 2007 Burr King Manufacturing Company. Inc. warrants the below product to be free in material and workmanship. The period of warranty is 1 year (90 days for vibratory bowls of 20 quart and lesser volume) from the date of purchase.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 June 21, 2007 LETTER OF AUTHENTICITY This letter is to certify that all Burr King Belt grinders, Disc grinders, Polishing machines Vibra King Chambers and Bowls are manufactured and assembled in the United States of America. (Tariff number 847990 criterion A) Don Mac Carthy President See our catalog at www.burrking.com contact us at info@burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.CO M (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 February 2005 OPERATOR, and OPERATING AREA SAFETY Subject equipment includes Grinders, buffers, polishers, and other rotating equipment. Serious injury or death may occur if minimum safety precautions are not understood, and obeyed by operators and those other persons who may be in the immediate vicinity of the subject equipment.
Continued from page 1 of the work rest (or table) will permit passage of the work piece through the gap (nip point). Note, however, that certain alloys such as titanium may create conditions where grinding debris can accumulate in a tight gap creating a potential fire hazard. When in doubt consult with your safety officer. Failure to observe this warning may result in the work piece or other item being caught in this gap, and/or being forcibly ejected.
Continued from page 2 Occupational Noise Exposure Burr King products produce levels of noise consistent with their intended purposes. The level and spectral content of noise produced is dependent on the product type, the degree that the product is maintained in proper operating condition, the abrasive/media and accessories used, the specific application, and the surrounding environment.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW, MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 Technical tip May 16, 2006 As you may know we improved many of our 120 and 220-volt single-phase variable speed grinders and buffers to use a three-phase AC motor with an inverter controller rather than the DC motors and a rectifier controller previously used. This change is transparent to the end user since the machine is “plugged in” to single-phase outlets.
motors. To force these inadequate services to deliver power that is greater than their designed 15-ampere capability leads to early equipment failure and potential fire danger. This must always be considered when choosing the electrical supply. • • • • • • Burr King provides 1-½ horsepower, 120-volt machines with a 20-ampere power cables and connectors.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 June 1999 Operating instructions for the Model 600/800 buffer The model 600/800 buffer is a single spindle buffer designed to use cotton, nylon, flap, wire, and other buffing and/or deburring wheels. Stone or vitreous grinding wheels must not be used on the model 600/800. For maximum effectiveness, and operator safety use wheels manufactured by well respected manufacturers.
model 600/800 spindle. A buffing wheel running in reverse rotation can unscrew from the spindle, creating a serious personnel safety hazard. 3. Engage the motor by placing the ON/OFF switch to ON. The wheel should rotate smoothly in a CCW direction with the front face of the buffing wheel moving toward the floor. If either of these conditions are not met turn the machine OFF immediately. b.
M600 BURR KING SCHEMATIC 17 1220 TAMARA LANE WARSAW, MO.
BURR KING ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NUMBER 731 600 4 1 6 701 903 5 31 WA1 728A 3 729 730 725 728 2 MOTOR* M600 1220 TAMARA LANE WARSAW, MO. 65355 DESCRIPTION BASE, MACHINE FRAME, MAIN WASHER, 5/16 SAE ZINC PLTD BOLT, 5/16-18x1 HEX HEAD 1/4-20 x 1 1/2 FH SOC BEARING, CONTACT WHEEL ASSY GUARD, CONTACT WHEEL WASHER, 1/4 AN SCREW 1/4-20x1 1/4 SHCS ADAPTER 1" STUD, GUARD, V, BELT NUT, 1/4-20 JAM, PLTD BELT, V DRIVE PULLEY, 3.0 PULLEY, 2.
M600 BURR KING FOOT PRINT 1220 TAMARA LANE WARSAW, MO. 65355 0.45 11.25 0.45 19.0 8.75 0.38 6.625 TOP VIEW 10.50 17.0 12.25 FRONT VIEW 9.
M800 BURR KING SCHEMATIC 17 1220 TAMARA LANE WARSAW, MO.
BURR KING ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NUMBER 731 600 4 37 6 701 903K 5 31 WA14 728A 3 729 730 725 728 2 MOTOR M800 1220 TAMARA LANE WARSAW, MO. 65355 DESCRIPTION BASE, MACHINE FRAME, MAIN WASHER, 5/16 SAE ZINC PLTD BOLT, 5/16-18x3/4 HEX HEAD 1/4-20 x 1 1/2 FH SOC BEARING, CONTACT WHEEL ASSY GUARD, CONTACT WHEEL WASHER, 1/4 AN SCREW 1/4-20x1 1/4 SHCS ADAPTER 1- 1/4" STUD, GUARD, V, BELT NUT, 1/4-20 JAM, PLTD BELT, V DRIVE PULLEY, 3.0 PULLEY, 2.
M800 BURR KING FOOT PRINT 11.25 1220 TAMARA LANE WARSAW, MO. 65355 0.45 20 8.75 0.38 6.18 20 10.23 12.25 0.45 9.
MAG STARTER BURR KING PARTS LIST 1220 TAMARA LANE WARSAW, MO.
BURR KING 1220 TAMARA LANE WARSAW, MO. 65355 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 MAG STARTER PART NUMBER DESCRIPTION MB-4C BRACKET, MOUNTING, STARTER MOTOR CALL FACTORY FOR PART NUMBER 4 WASHER, 5/16 SAE ZINC PLTD 37 BOLT, 5/16-18x3/4 HEX HEAD 5 WASHER, 1/4 AN 209 SCREW, 1/4-20 X 3/4 ALLEN HEAD 4-0013 NUT, KEP, 1/4-20 MS2A3 3/4HP-1HP, 220V MS4A3 3/4HP-1HP, 440V MS2B3 1.5HP-3HP, 220V MS4B3 1.5HP-3HP, 440V 775 CONNECTOR, 3/8", STR, LIQ. TIGHT 776 CONNECTOR, 3/8", 90 DEG, LIQ.
VARI SPEED BURR KING SINGLE PHASE 1220 TAMARA LANE WARSAW, MO. 65355 3/4-1 HP 1.
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VARI SPEED PART NUMBER MB-4C 941-3 5-0032 4 209 5 4-0013 100B-1725C 150B-1725C 37 015-1 017 020 864-1 775 776 643 862-3 DESCRIPTION BRACKET, MOUNTING, STARTER BRACE, MB4 SUPPORT WASHER, 1/4, LOCK, SPLIT, PLTD WASHER, 5/16 SAE ZINC PLTD SCREW, 1/4-20 X 3/4 ALLEN HEAD WASHER, 1/4 AN NUT, KEP, 1/4-20 1 HP MOTOR 1.5 HP MOTOR BOLT, 5/16-18x3/4 HEX HEAD 120V CORD 220V CORD CONDUIT 3/8" LIQUIDTIGHT CONT. 115/220V 0.75-1HP CONNECTOR, 3/8" STR, LIQ.
