Installation Manual

HOOK TOP
SNAP BOTTOM
HOOK BOTTOM
SNAP TOP
Auto Dimming Wires
from Mirror Head
Snap Lock Guide
Heating Terminal Wires
Motor Head
Lower Hook Lock
Upper Snap Lock
Heating Terminal
Leads
Redi-Set-Go
Pre-Applied
Motor Mount
Hook Lock Guide
(For Heated Mirrors)
(For Auto Dimming Mirrors)
(For Heated Mirrors)
Mirror Head
ALIGN ABOVE
Upper Tab Lock Guide
Mirror Head
Lower Tab Lock
SLIDE
DOWN
Upper Tab Lock
Heating Terminal Leads
Heating Terminal Wires
Motor Head
Redi-Set-Go
Pre-Applied
Motor Mount
(For Heated Mirrors)(For Heated Mirrors)
(For Heated Mirrors) (For Heated Mirrors)(For Auto Dimming Mirrors)
Motor Head
Redi-Set-Go
Pre-Applied
Motor Mount
Heating Terminal Wires
(Female) from Mirror Head
Auto Dimming Wires
from Mirror Head
Heating Terminal Leads
(Male) from Mirror
Snap Tabs
Snap Tabs
Mirror Head
SNAP IN
Auto Dimming Wires
from Mirror Head
(For Auto Dimming Mirrors)
Auto Dimming Wires
from Mirror Head
(For Auto Dimming Mirrors)
Heating
Terminal Wires
(For Heated Mirrors)
(For Heated Mirrors)
Hook Lock Guide
Motor Head
Mirror Head
Lower Snap Lock
Upper Hook Lock
Heating
Terminal Leads
Redi-Set-Go
Pre-Applied
Motor Mount
© 2016 Burco, Inc.
Snap Lock Guide
© 2016 Burco, Inc.
© 2016 Burco, Inc.
© 2016 Burco, Inc.
Lower Tab Lock Guide
REDI-SET-GO
1
INSTALL
REDI-SET-GO
2
INSTALL
REDI-SET-GO
3
INSTALL
REDI-SET-GO
4
INSTALL
STEP 1: REMOVE MIRROR AND BACKING PLATE
Manually pivot mirror downward by applying pressure to the lower portion of your mirror.
Insert a screwdriver above mirror behind backing plate and carefully pry off backing plate
snap tabs from the motor head.
TIP: Place a towel on edge of mirror head when prying off backing plate to prevent damage
or scratching.
STEP 2: DETACH WIRES
If your mirror is a heated variant, disconnect terminal leads from your mirror’s heating element.
If applicable, auto dimming or signal wires may have to be disconnected or clipped and capped.
NOTE: Burco mirror replacements do not auto dim.
STEP 3: DISPOSAL
Throw away your old backing plate and broken glass.
STEP 4: RECONNECT WIRES & TEST
If your mirror is a heated or signal variant, reconnect terminal wires to Redi-Set-Go™ mirror
replacement. Test functionalities before proceeding to the next step.
STEP 5: INSTALL
Align motor mount snap tabs with motor. Apply gentle even pressure until motor mount
snaps onto motor head.
STEP 6: CLEAN UP
Clean your installed Redi-Set-Go™ mirror replacement with glass cleaner.
Snap tab backing plate removal.
STEP 1: REMOVE MIRROR AND BACKING PLATE
Manually pivot mirror and backing plate upward by applying pressure on the upper portion of
your mirror. Insert a screwdriver below your mirror and backing plate and carefully pry lower
snap locks off the snap lock guides. Once lower snap locks pop off, pull down/out to release
the upper hook locks from the hook lock guides.
TIP: Place a towel on edge of mirror head when prying off lower snap locks to prevent
damage or scratching.
STEP 2: DETACH WIRES
If your mirror is a heated variant, disconnect terminal leads from your mirror’s heating element.
If applicable, auto dimming or signal wires may have to be disconnected or clipped and capped.
NOTE: Burco mirror replacements do not auto dim.
STEP 3: DISPOSAL
Throw away your old backing plate and broken glass.
STEP 4: RECONNECT WIRES & TEST
If your mirror is a heated or signal variant, reconnect terminal wires to Redi-Set-Go™ mirror
replacement. Test functionalities before proceeding to the next step.
STEP 5: INSTALL
Insert upper hook locks into the hook lock guides. Next, apply gentle pressure and snap lower
snap locks into snap lock guides.
TIP: Be sure upper hook locks are fully seated before snapping lower snap locks into place.
STEP 6: CLEAN UP
Clean your installed Redi-Set-Go™ mirror replacement with glass cleaner.
Upper hook lock backing plate removal.
STEP 1: REMOVE MIRROR AND BACKING PLATE
Manually pivot mirror and backing plate downward by applying pressure to the lower portion
of your mirror. Insert a screwdriver above your mirror and backing plate and carefully pry upper
snap locks out of the snap lock guides. After the upper snap locks pop off, pull up/out to
release lower hook locks from the hook lock guides.
TIP: Place a towel on edge of mirror head when prying upper snap locks off to prevent
damage or scratching.
STEP 2: STEP 2: DETACH WIRES
If your mirror is a heated variant, disconnect terminal leads from your mirror’s heating element.
If applicable, auto dimming or signal wires may have to be disconnected or clipped and capped.
NOTE: Burco mirror replacements do not auto dim.
STEP 3: DISPOSAL
Throw away your old backing plate and broken glass.
STEP 4: RECONNECT WIRES & TEST
If your mirror is a heated or signal variant, reconnect terminal wires to Redi-Set-Go™ mirror
replacement. Test functionalities before proceeding to the next step.
STEP 5: INSTALL
Insert lower hook locks into the hook lock guides. Next, apply gentle pressure and snap upper
snap locks into snap lock guides.
TIP: Be sure lower hook locks are fully seated before snapping upper snap locks into place.
STEP 6: CLEAN UP
Clean the installed Redi-Set-Go™ mirror replacement with glass cleaner.
Lower hook lock backing plate removal.
STEP 1: REMOVE MIRROR AND BACKING PLATE
Insert a screwdriver below your mirror and carefully slide tab locks off of tab lock guides
by lifting/prying upward.
TIP: Lift/pry upward. Do not pry outward.
TIP: Place a towel on edge of mirror head when prying up to prevent damage or scratching.
STEP 2: DETACH WIRES
If your mirror is a heated variant, disconnect terminal leads from your mirror’s heating element.
If applicable, auto dimming or signal wires may have to be disconnected or clipped and capped.
NOTE: Burco mirror replacements do not auto dim.
STEP 3: DISPOSAL
Throw away your old backing plate and broken glass.
STEP 4: RECONNECT WIRES & TEST
If your mirror is a heated or signal variant, reconnect terminal wires to Redi-Set-Go™ mirror
replacement. Test functionalities before proceeding to the next step.
STEP 5: INSTALL
Vertically align your Redi-Set-Go™ mirror replacement toward the top of the mirror head.
Apply gentle downward pressure and slide tab locks onto tab lock guides.
TIP: For more clearance, pivot motor head downward.
STEP 6: CLEAN UP
Clean your installed Redi-Set-Go™ mirror replacement with glass cleaner.
Slide tab backing plate removal.