Rapid Flow Induction Vehicle Application Part Number Ford 7.
RAPID FLOW INDUCTION Introduction TROUBLESHOOTING: Stock Removal If you have questions during the installation of this product, please visit www.bullydog.com/Product_Updates.php. The latest version of these instructions can be found at the same location. Please review the Troubleshooting section on page 9 before calling technical support to cover most common issues. Technical support is available by calling 866-bullydog (866-285-5936). RFI Installation TABLE OF CONTENTS Introduction....................
RAPID FLOW INDUCTION Introduction Introduction Introduction: The following instruction set covers installation and maintenance of the Rapid Flow induction system for ‘94-’97 7.3L Ford Power Strokes. The Bully Dog Rapid Flow Induction System has been designed to allow more air to flow though your engine. This allows a more complete burn of the fuel in your combustion chamber which adds additional horsepower and fuel economy.
RAPID FLOW INDUCTION Introduction Removing the Stock intake In these steps you will remove the stock intake system. Stock Removal 1. Locate the stock air intake inside the engine bay on the driver side of the vehicle towards the front of the engine bay. 2. Remove the intake hose from the stock intake using a flat head screw driver to loosen the clamp. Locate Stock Intake RFI Installation Filter Maintenence 3.
RAPID FLOW INDUCTION Introduction 4. Locate the air sensor on the right side of the intake. Remove the sensor from the intake by twisting it counter clockwise and pulling it out. Air Sensor Stock Removal Remove Air Sensor RFI Installation 5. Remove the nut at the back right side of the intake by removing with a 10mm end wrench. (Save this nut for later use). Finally remove the intake from the vehicle by pulling it straight up to release it from the two rubber grommets which hold it in place.
RAPID FLOW INDUCTION Introduction Installing the RFI Secure with Stock Nut Stock Removal Air Sensor Holder Reuse Rubber Grommets RFI Installation Quick Overview of Important Parts In these steps you will install the Rapid Flow Induction System. Filter Maintenence 1. This is a very easy install. However, it is easy to skip a step so please review the steps to ensure that you don’t miss one. Troubleshooting/FAQ 2. You will need to remove the two stock rubber grommets from the stock intake.
RAPID FLOW INDUCTION Introduction 3. Install the stock rubber grommets in the two holes at the base of the RFI system. Stock Removal Install Grommets in Base of RFI 4. Align the RFI system so that the air filter points towards the outside of the vehicle, and press down to secure the RFI in place. RFI Installation Press RFI into place Filter Maintenence 5. Attach the air sensor to the sensor holder on the RFI system.
RAPID FLOW INDUCTION Introduction 7. Attach both the air hose onto the RFI system and air filter onto the RFI system and secure with clamps using a flat head screwdriver.
RAPID FLOW INDUCTION Part 1, Cleaning the filter: 1. Remove filter from filter housing. Clean the filter housing if necessary. RFI Installation 2. Begin the cleaning process by ridding the filter of any dirt by lightly tapping it. Then brush away any loose particles with a soft-bristle brush. This step can usually be avoided with the use of a prefilter. Stock Removal The intake system should be cleaned at least every three months; in dusty climates the filter should be cleaned more often.
RAPID FLOW INDUCTION Troubleshooting/FAQ Introduction CONDITION How often should I clean the filter? Stock Removal Can I purchase a second filter? RFI Installation Why use a pre-filter? Filter Maintenence How long is required to let the filter dry after oiling the filter? Troubleshooting/FAQ What does the Bully Dog Cleaning Kit include? Warranty/Disccliamer POSSIBLE SOURCES Maintenance Maintenance Maintenance Maintenance ACTION Depending on conditions, generally 5,000 miles or 3 months.
RAPID FLOW INDUCTION Warranty & disclaimer Introduction REMEMBER, THIS IS A PERFORMANCE PRODUCT, USE AT YOUR OWN RISK. This product is not intended to be used to break the law. Do not use this product until you have carefully read the following agreement. This agreement sets forth the terms and conditions for the use of this product. The installation of this product indicates that the buyer has read and understands this agreement and accepts the terms and conditions.
Bully Dog Technologies, LLC is a team built on integrity that is dedicated to leading the vehicle performance industry with an uncompromising code of ethics demonstrated in the soundness of its employees, excellent customer service and superior products. UNLEASH THE POWER WITH BULLY DOG PERFORMANCE PRODUCTS Downloaders Intake Systems Custom OutLook Pod Exhaust Systems See More at: bullydog.com Doc.# BD51020 Version 1.0.3 For a full listing of Diagnostic Trouble Codes go to: www.bullydog.com/DTC.
