Programming instructions

 

7
6. Use electrical t6. Use electrical tape to wrap. Be sure to cover the wire ape to wrap. Be sure to cover the wire about two inches on eitherabout two inches on either
side of the connection. First pull side of the connection. First pull the wire that you have just connected along the wire that you have just connected along
side the wire you connected to, tside the wire you connected to, tape and wire tie them togetherape and wire tie them together. Use this method. Use this method
for all connections.for all connections.
CAUTION:CAUTION: All wires must be wrapped with tAll wires must be wrapped with tape and wire tied.ape and wire tied.
2. 2. TTwist upper wires togetherwist upper wires together, twist lower wires together , twist lower wires together as shown.as shown.
1. When tying two sep1. When tying two separate wires together at their ends, strip back 1 of insulationarate wires together at their ends, strip back 1 of insulation
on both wires and sepon both wires and separate arate the strands of wire as shown belowthe strands of wire as shown below..
MAKING END MAKING END TTO END CONNECTIONSO END CONNECTIONS
MAKING CONNECTIONS
Wire Wire TTieie
Electrical Electrical TTapeape
4. Insert the wire(s) from the st4. Insert the wire(s) from the starter through the hole as shown. If arter through the hole as shown. If two or more wires are inserted,two or more wires are inserted,
wrap them in opposite directions.wrap them in opposite directions.
5.5. WWrap the wire around one side then the other and finally around irap the wire around one side then the other and finally around ittself as shown.self as shown.
11
22
33
Use this method ONLUse this method ONLYY when connecting two sep when connecting two separate wires end to end.arate wires end to end.
ManufacturerManufacturer Make/ Make/ YYearear Anti-thefAnti-theftt 
Acura TL 99+ TRANSPONDER 
CL 98+ TRANSPONDER 
RL 99+ TRANSPONDER 
INTEGRA 00 + TRANSPONDER 
NSX TRANSPONDER 
AUDI A4 00+ TRANSPONDER 
A6 00+ TRANSPONDER 
A8 98+ TRANSPONDER 
BMW ALL 97+ TRANSPONDER 
BUICK CENTURY 97+ VATS 
LESABRE 90-96, 2000 VATS 
PARK AVE 91-96 VATS 
PARK AVE 97+ TRANSPONDER 
REGAL 93-96 VATS (Some)
RIVIERA 93-99 VATS (Some)
ROADMASTER 93-96 VATS 
SKYLARK 96-98 PASSLOCK 1 
CADILLAC ALLANTE 91-93 VATS 
BROUGHAM 90-96 VATS 
CATERA 98+ TRANSPONDER 
DEVILLE 92-96 VATS 
DEVILLE 99+ TRANSPONDER 
ELDORADO 89-98 VATS 
ELDORADO 99+ VATS 
ESCALADE 99+ PASSLOCK 2 
FLEETWOOD 90-96 VATS 
SEVILLE 90-98 VATS 
SEVILLE 99+ TRANSPONDER 
SLS/ STS 97+ TRANSPONDER 
CHEVROLET ASTRO 98+ PASSLOCK 2 
BLAZER 98+ PASSLOCK 2 
CAMARO 86+ VATS 
CAVALIER 95-99 PASSLOCK 1 
CAVALIER 2000+ PASSLOCK 2 
CORVETTE 88+ VATS 
EXPRESS 98+ PASSLOCK 2 
IMPALA 2000+ PASSLOCK 2 
LUMINA 96+ VATS 
VÉHICULES AVEC SYSTÈME
ANTIDÉMARRAGE DE LUSINE
38
3. Sep3. Separate the vehicle wire(s) as shown. Make the separate the vehicle wire(s) as shown. Make the separation large enough to fit the otheraration large enough to fit the other
wire through.wire through.
2. S2. Strip back one inch of insulation on the wire you need to connecttrip back one inch of insulation on the wire you need to connect to. to.
One Inch of Bare WireOne Inch of Bare Wire