Installation guide

ManualsBrandsBulldog Security ManualsHome building and Decor721

CONTENTS

REMOTE STARTER

MODELS DELUXE 12 and DELUXE 22

INSTALLATION GUIDE

•

OWNER’S GUIDE

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

System Features.................................................... 1

System Components.................................................. 1

Tools Required..................................................... 1

Technical Assistance ............................................... 1

Before You Begin................................................... 2

Precautions ....................................................... 2

Making Connections ............................................... 2-4

Locating & Making Connections ..................................... 4-6

Neutral Safety Switch .............................................. 6

Antenna Placement.................................................. 7

Connecting The 18-Pin Harness and 4-Relay Harness .................... 7

Factory Anti-Theft System........................................... 7

Testing Door Locks ................................................. 8

Connecting Door Locks .............................................. 8

Installation Programming Instructions................................ 9

Operator Programming Instructions .................................. 10

How to Use Your Remote Transmitter............................... 10-11

Summary of content (12 pages)

PAGE 1
INSTALLATION GUIDE • OWNER’S GUIDE REMOTE STARTER MODELS DELUXE 12 and DELUXE 22 CONTENTS System Features.................................................... 1 System Components .................................................. 1 Tools Required..................................................... 1 Technical Assistance ............................................... 1 Before You Begin ................................................... 2 Precautions ...............................................
PAGE 2
SYSTEM FEATURES 2 Four-Button Extended Range Remote Control Remotely start your car to run the heater or air conditioning from an extended distance. (1 transmitter only with Model Deluxe 12) Keyless Entry Remotely locks and unlocks your power door locks with built-in relays onboard. Ignition Controlled Door Locks A programmable feature that locks and unlocks the doors when the brake is depressed or the ignition is cycled. Trunk Release Remotely opens your trunk with a push of a button.
PAGE 3
BEFORE YOU BEGIN Congratulations, you have purchased one of the most advanced remote starter systems ever made. Your new system is a technological breakthrough utilizing the most advanced, state of the art technology and components. It is computer controlled and manufactured in the U.S.A. The dependability and variety of features make Bulldog Security the leader in the industry.
PAGE 4
3. Separate the vehicle wire as shown. Make the separation large enough to fit the other wire through. 4. Insert the wire from the unit through the hole as shown. 5. Wrap the wire around one side then the other and finally around itself as shown. 1 2 3 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together.
PAGE 5
4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. Electrical Tape Wire Tie Wire Tie Use this method ONLY when connecting two separate wires end to end. LOCATING & MAKING CONNECTIONS Please see the wiring chart on our website, www.bulldogsecurity.com.
PAGE 6
DIESEL INSTALLATION ONLY Connecting the Glow Plug or Wait to Start Wire When installing on a diesel engine, a wire that energizes the Glow Plug (also known as the Wait to Start Wire), must be located and identified. This wire is usually located at the instrument cluster or at the ECM (electronic control module). This wire will, depending on the year, make and model of the vehicle, test as a (+) positive or a (-) negative.
PAGE 7
DOME LIGHT SUPERVISION (Optional Part #775 required) Before connecting the DOME LIGHT SUPERVISION, you must determine if your dome light is a (+) POSITIVE or a (-) NEGATIVE. TO TEST for a (+) POSITIVE dome light wire, clip your test light to a good solid ground, probe the dome light wire with the door closed and the dome light out, the test light should not be illuminated. Open the door and the dome light turns on. If the test light is now illuminated this is a (+) POSITIVE dome light wire.
PAGE 8
CONNECTING THE 18-PIN HARNESS & 4-RELAY HARNESS 5-Pin Door Lock Harness DOOR LOCK & UNLOCK OUTPUT ANTENNA CONNECTOR BROWN/BLACK GREEN/BLACK BLACK/WHITE BLACK/BLUE BLUE VIOLET WHITE/RED ORANGE BROWN GRAY GRAY/BLACK YELLOW BLUE/BLACK BLACK/YELLOW GREEN RED/BLACK BLACK RED (+) Diesel output (-) Diesel output Tach (-) to neg.
PAGE 9
TESTING DOOR LOCKS TESTING: Door Locks There are three basic types: “Type A” Door Lock Test (Most GMs and some Chryslers) Probe both of your door lock wires going to the door lock switch usally located in the driver’s kick panel. Attach the clip end of your test light to a good chassis ground. Using the vehicle’s door lock controls, activate the lock then the unlock, testing both wires one at a time.
PAGE 10
“Type C” Reverse Polarity (5-pin harness) POWER DOOR LOCK MOTOR KEYLESS MODULE GREEN/BLACK Unlock GREEN/WHITE Unlock RED/BLACK FUSE +12V Constant BLUE/BLACK Lock BLUE/WHITE Lock NOTE: Connect the RED WITH BLACK STRIPE wire to +12V constant power fused at 30 amps. NOTE: You will need to cut factory wiring to make an end to end connection, see “Making Connections” on page 2-4.
PAGE 11
Programming Door Lock Pulse Length 3.5 (from .7 to 3.5 seconds) Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3) times. Release Button #3 (trunk). Press and release Button #1 (start), the parking lights will flash once, the door lock pulse length is now 3.5 seconds. Release the brake, the parking lights will flash three (3) times. NOTE: Factory Door Lock Pulse Setting is .7 seconds.
PAGE 12
HOW TO USE YOUR REMOTE TRANSMITTER BUTTON #1 Remote starts your vehicle. Start Lock n U lock Trunk Stop BULLDOG BUTTON #2 Locks and unlocks your power door locks. BUTTON #3 Pops your trunk. BUTTON #4 Turns off your remote starter. Starting the Vehicle with the Remote Transmitter Press and release button #1 (start). The parking lights will flash once, confirming the car starter received the signal. The car will then start and the parking lights will turn on and remain on while the vehicle is running.