Installation guide

ManualsBrandsBulldog Security ManualsHome building and Decor721

CONTENTS

ALARM AND REMOTE STARTER MODEL DELUXE 62

INSTALLATION GUIDE

•

OWNER’S GUIDE

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

System Features ....................................... 1

System Components ..................................... 1

Tools Required ........................................ 1

Technical Assistance .................................. 2

Before You Begin ...................................... 2

Precautions........................................... 2

Making Connections .................................. 3-4

Locating & Making Connections ........................ 4-7

Neutral Safety Switch ................................. 8

Antenna Placement ..................................... 8

Connecting The 18-Pin Harness & 4-Relay Harness......... 8

Factory Anti-Theft System.............................. 9

Testing Door Locks .................................... 9

Connecting Door Locks............................... 9-10

How to Use Your Remote Transmitter .................... 10

Installation Programming Instructions ................. 11

Operator Programming Instructions .................. 11-12

Summary of content (13 pages)

PAGE 1
INSTALLATION GUIDE • OWNER’S GUIDE ALARM AND REMOTE STARTER MODEL DELUXE 62 CONTENTS System Features ....................................... 1 System Components ..................................... 1 Tools Required ........................................ 1 Technical Assistance .................................. 2 Before You Begin ...................................... 2 Precautions ........................................... 2 Making Connections ..................................
PAGE 2
SYSTEM FEATURES 2 Four-Button Extended Range Remote Control Remotely start your car to run the heater or air conditioning from an extended distance. Keyless Entry Remotely locks and unlocks your power door locks with built-in relays onboard. Built In Alarm Features Provides door, hood and impact protection. Onboard Dual Stage Shock Sensor Provides warn away protection and impact protection. Door Trigger Protection Provides protection when doors are opened.
PAGE 3
TECHNICAL ASSISTANCE Should you need help. First check our website at www.bulldogsecurity.com/wires.htm or call our toll-free Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM-4PM EST at 800-878-8007.
PAGE 4
MAKING WIRING CONNECTIONS 1. Strip back two inches of insulation on the wire from the keyless entry. Two Inches of Bare Wire 2. Strip back one inch of insulation on the wire you need to connect to. One Inch of Bare Wire 3. Separate the vehicle wire as shown. Make the separation large enough to fit the other wire through. 4. Insert the wire from the unit through the hole as shown. 5. Wrap the wire around one side then the other and finally around itself as shown. 1 2 3 6. Use electrical tape to wrap.
PAGE 5
2. Twist upper wires together, twist lower wires together as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. Electrical Tape Wire Tie Wire Tie Use this method ONLY when connecting two separate wires end to end. LOCATING & MAKING CONNECTIONS Please see the wiring chart on our website, www.
PAGE 6
ACCESSORY WIRE(S) THAT POWER THE HEATER/BLOWER MOTOR (+12V in run or on positions) This wire is also in the main ignition switch harness usually located in the steering column. Make all connections as close to the ignition switch harness as possible. Most vehicles will have (1) accessory wire; however some Fords, newer GM vehicles and Chrysler 94 and up will have (2) or more accessory wires. To locate these wire(s) probe for wire(s) that only show +12V when the ignition switch is in the RUN or ON positions.
PAGE 7
HOOD PIN SWITCH This feature will keep the engine from starting or shut off the engine when the hood is opened. Locate a good chassis ground, if at all possible do not install the pin switch in the rain gutter. Drill a 5/16 hole, insert the pin switch into the hole and tighten. Check for the hood adjustment, there is approximately 1/4” adjustment in the pin switch.
PAGE 8
NEGATIVE TRUNK RELEASE TRUNK RELEASE OUTPUT (Optional Part #775 required) POSITIVE TRUNK RELEASE Locate the trunk release wire coming from the Optional part #775 required. back of the trunk release switch. You must TO FACTORY TRUNK WIRE TO FACTORY TRUNK WIRE determine if your trunk release is a (+) POSITIVE YELLOW YELLOW or a (-) NEGATIVE. (most trunk releases are (+) positive).
PAGE 9
NEUTRAL SAFETY SWITCH PRE-1996 GM REAR WHEEL DRIVES WITH PURPLE CRANK WIRE – Optional part #775 required. MECHANICAL NEUTRAL SAFETY SWITCH (Rear Wheel Drive Only) When installing a Bulldog remote starter on GM vehicles or Dodge Dakotas built prior to 1996, you must: Use the diagram below to create a circuit that will prevent the remote starter from starting the vehicle unless the key is removed from the ignition switch. YELLOW PRE-1996 DODGE DAKOTAS Optional part #775 required.
PAGE 10
FACTORY ANTI-THEFT SYSTEMS FOR GENERAL MOTORS CARS ONLY System 1: PASSKEY I and II system (1985 and up). This system has a resistor pill in the key. Measure resistance of the pill using a test meter. A bypass module is available, part #VATS-WR module. System 2: PASSLOCK I and II system (1995 and up). Passlock does not have a pill in the key. It has a light on the dash that states ANTITHEFT OR SECURITY system. A bypass module is available, part #GMBP-721 module. System 3: PASSKEY III system (GM 1998 and up).
PAGE 11
CONNECTING DOOR LOCKS “Type A” (+) Positive (5-pin harness) “Type B” (-) Negative (5-pin harness) GREEN/BLACK Unlock KEYLESS MODULE KEYLESS MODULE GREEN/BLACK Unlock GREEN/WHITE Not Used UNLOCK RED/BLACK FUSE +12V Constant LOCK BLUE/BLACK Lock BLUE/WHITE Not Used GREEN/WHITE Not Used UNLOCK RED/BLACK FUSE LOCK BLUE/BLACK Lock BLUE/WHITE Not Used NOTE: Connect the RED WITH BLACK STRIPE wire to +12V constant fused at 30 amps. Ground NOTE: Connect the RED WITH BLACK STRIPE wire to ground.
PAGE 12
Trunk Pop Output The remote car starter includes an optional output that can be used to do one of the following: open the trunk (optional relay required), roll up the windows (optional module needed), close the sun roof (optional module needed) etc. This output will pulse .75 seconds when pressed and released. In instances where a continuous signal is needed such as sun roof and power windows, hold down Button #3 (trunk) as long as the signal is needed to complete the task.
PAGE 13
Programming Shock Sensor On and Off (See Adjusting Shock Sensor) Press and hold the brake, then press and hold Button #4 (stop) until the parking lights flash four (4) times. Release Button #4. Press and release Button #2, the parking lights will flash once the shock sensor is now ON. Press and release Button #2, the parking lights will flash twice the shock sensor is now OFF. Release the brake, the parking lights will flash three (3) times. The programming is now entered.