User`s guide

4-4
ESCALA T610 and PL 600T User’s Guide
Adapter Parameters
Select the Adapter Parameters option from the Network Parameters menu to view an
adapter’s hardware address, as well as configure network adapters that require setup. A
screen similar to the following displays when you make this selection:
+––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––+
| |
|Adapter Parameters |
| |
| Device Slot Hardware Address |
| |
| 1. Gigabit Ethernet 4: U0.1–P1–I4/E1 0004ac7c0135 |
| 2. token–ring 5: U0.1–P1–I5/T1 0020357a9105 |
| 3. ethernet Integrated:U0.1–P1/E1 0060949d7ac5 |
| 4. ethernet 2: U0.2–P1–I2/E1 0004ac5e692b |
| 5. token–ring 3: U0.2–P1–I3/T1 0004ac634e38 |
| |
| |
| |
| .––––––. |
| |X=Exit| |
| ‘––––––’ |
| (PRESS ENTER AFTER MAKING A SELECTION) ===> |
+––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––+
Select an adapter on this screen to display configuration menus for that adapter. If ethernet
is selected, you can set parameters that control how the ethernet adapter communicates
with the network. For example, the following screen shows the menu for the ethernet
adapter configuration:
+––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––+
| |
| |
| |
| |
|1. Data Rate [Auto] |
|2. Full Duplex [No] |
| |
| |
| |
| |
| |
| |
+––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––+
Ping
Select Ping from the Network Parameters menu to test a connection to a remote system
unit. After selecting the Ping option, you must first choose an adapter to communicate with
the remote system.
+––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––+
| |
|Adapter Parameters |
| |
| Device Slot Hardware Address |
| |
| 1. Gigabit Ethernet 4: U0.1–P1–I4/E1 0004ac7c0135 |
| 2. token–ring 5: U0.1–P1–I5/T1 0020357a9105 |
| 3. ethernet Integrated:U0.1–P1/E1 0060949d7ac5 |
| 4. ethernet 2: U0.2–P1–I2/E1 0004ac5e692b |
| 5. token–ring 3: U0.2–P1–I3/T1 0004ac634e38 |
| |
| |
| |
| .––––––. |
| |X=Exit| |
| ‘––––––’ |
| (PRESS ENTER AFTER MAKING A SELECTION) ===> |
+––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––+
After determining which adapter to use to ping the remote system, you must provide the
addresses needed to communicate with the remote system. Select the appropriate device
from the Ping menu to display a screen similar to the following: