2011 Buick Regal Owner Manual M In Brief . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information . . . . . . . . 1-4 Vehicle Features . . . . . . . . . . . . . 1-12 Performance and Maintenance . . . . . . . . . . . . . . . . 1-17 Safety Belts . . . . . . . . . . . . . . . . . . . . 3-8 Airbag System . . . . . . . . . . . . . . . . 3-23 Child Restraints . . . . . . . . . . . . . . 3-36 Storage . . . . . . . . . . . . . . . . . . . . . .
011 Buick Regal Owner Manual M Vehicle Care . . . . . . . . . . . . . . . . . 10-1 General Information . . . . . . . . . . 10-2 Vehicle Checks . . . . . . . . . . . . . . . 10-4 Headlamp Aiming . . . . . . . . . . . 10-28 Bulb Replacement . . . . . . . . . . 10-28 Electrical System . . . . . . . . . . . . 10-32 Wheels and Tires . . . . . . . . . . . 10-38 Jump Starting . . . . . . . . . . . . . . . 10-68 Towing . . . . . . . . . . . . . . . . . . . . . . 10-71 Appearance Care . . . . . . . . . . .
Introduction Motors of Canada Limited” for Buick Motor Division wherever it appears in this manual. Keep this manual in the vehicle for quick reference. GENERAL MOTORS, GM, the GM Emblem, BUICK, the BUICK Emblem, and the name REGAL are registered trademarks of General Motors LLC. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual.
iv Introduction { WARNING These mean there is something that could hurt you or other people. Notice: This means there is something that could result in property or vehicle damage. This would not be covered by the vehicle's warranty. the text describing the operation or information relating to a specific component, control, message, gauge, or indicator. M : This symbol is shown when you need to see your owner manual for additional instructions or information.
In Brief In Brief Instrument Panel Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information Initial Drive Information . . . . . . . . Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . Door Locks . . . . . . . . . . . . . . . . . . . Trunk Release . . . . . . . . . . . . . . . . Windows . . . . . . . . . . . . . . . . . . . . . . Seat Adjustment . . . . . . . . . . . . . . Heated Seats . . . . . . . . . . . . . . . . . Head Restraint Adjustment . . . .
1-2 In Brief Instrument Panel
In Brief A. Exterior Lamp Controls on page 6‑1. H. Steering Wheel Controls on page 5‑2. Fog Lamps on page 6‑4. I. Instrument Panel Illumination Control on page 6‑5. Windshield Wiper/Washer on page 5‑3. J. AM-FM Radio on page 7‑7. B. Air Vents on page 8‑3. K. Info Display. C. Turn and Lane‐Change Lever. See Turn and Lane-Change Signals on page 6‑3. L. Driver Information Center Buttons. See Driver Information Center (DIC) on page 5‑21. D. Cruise Control on page 9‑36. E.
1-4 In Brief Press 7 again to cancel the panic alarm. Initial Drive Information Press the button to extend the key. The key can be used for the ignition and all locks. This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. See Keys on page 2‑2 and Remote Keyless Entry (RKE) System Operation on page 2‑3. For more detailed information, refer to each of the features which can be found later in this owner manual.
In Brief Power Door Locks Windows The power door lock switches are located on the center of the instrument panel. K: Q: 1-5 Seat Adjustment Manual Seats 1. Pull the handle under the seat to unlock the seat. Press to unlock the doors. Press to lock the doors. 2. Slide the seat to the desired position and release the handle. See Vehicle Personalization on page 5‑29 for more information. Try to move the seat to be sure it is locked in place.
1-6 In Brief Power Seats To raise or recline the seatback, tilt the top of the control (B) forward or rearward. Head Restraint Adjustment See Reclining Seatbacks on page 3‑5. Do not drive until the head restraints for all occupants are installed and adjusted properly. Press the front or rear of the control (C) to increase or decrease lumbar support. See Lumbar Adjustment on page 3‑5. Heated Seats A. Power Seat Adjustment Control Heated Front Seats B.
In Brief Safety Belt Refer to the following sections for important information on how to use safety belts properly. . Safety Belts on page 3‑8. . How to Wear Safety Belts Properly on page 3‑11. . Lap-Shoulder Belt on page 3‑15. . Lower Anchors and Tethers for Children (LATCH System) on page 3‑44. Sensing System for Passenger Airbag The passenger sensing system turns off the right front passenger frontal airbag and the seat‐mounted side impact airbag under certain conditions.
1-8 In Brief Interior Mirror The vehicle has an automatic dimming inside rearview mirror. Automatic dimming reduces the glare from the headlamps of the vehicle behind you. The dimming feature and the indicator light come on each time the ignition is turned to start. Steering Wheel Adjustment Interior Lighting Dome Lamps The interior lamps control located in the overhead console controls both the front and rear interior lamps. *: 1: Turns the lamps off. Turns the lamps on when any door is opened.
In Brief Exterior Lighting 1-9 AUTO: Automatically turns the exterior lamps on and off, depending on outside lighting. The current status of the AUTO system is displayed in the Driver Information Center (DIC) display. See Driver Information Center (DIC) on page 5‑21. ;: Turns on the parking lamps, instrument panel lights, and other exterior lighting. #$: Press to turn each lamp on or off. The rear reading lamps are located in the headliner. For more information about interior lamps, see: .
1-10 In Brief Windshield Wiper/Washer & : Turn the band up for more frequent wipes or down for less frequent wipes. Windshield Washer Pull the windshield wiper lever to spray windshield washer fluid and activate the wipers. See Windshield Wiper/Washer on page 5‑3. 9 : Turns the windshield wipers off. The windshield wiper lever is on the side of the steering column. 2: Fast wipes. 1: Slow wipes. 3 : Briefly move the wiper lever down for a single wipe or hold down for several wipes.
In Brief Climate Controls Transmission The heating, cooling, and ventilation for the vehicle can be controlled with these systems. Automatic Transmission P: Park A. Air Conditioning G. Recirculation R: Reverse B. Driver and Passenger Temperature Controls H. Fan Controls N: Neutral I. AUTO (Automatic Mode) C. Heated Seats D: Drive J. Rear Defogger D. Air Delivery Modes See Dual Automatic Climate Control System on page 8‑1. E. Climate Display F.
1-12 In Brief Manual Mode Vehicle Features Move the selector lever from D (Drive) to the left. Press the shift lever forward (+) to upshift or rearward (−) to downshift. Radio(s) 3 O : Press to turn the system The selector lever can only be moved out of P (Park) when the ignition is on and the brake pedal is applied. To engage P (Park) or R (Reverse), push the release button. See Automatic Transmission on page 9‑24. on and off. Turn to increase or decrease the volume.
In Brief 5. To save the time and return to the Time Settings menu, press the BACK button at any time or press the Z button after adjusting the minutes. XM Satellite Radio Service 1. Press the CONFIG button and select Time Settings. XM is a satellite radio service based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast to coast, and in digital-quality sound. A fee is required to receive the XM service. 2.
1-14 In Brief Steering Wheel Controls Toggle up or down to select the next or previous favorite radio station, CD, or MP3 track. Driver Information Center (DIC) + x −: Press + to increase the volume, press − to decrease the volume. The DIC display is located in the center of the instrument panel cluster. It shows the status of many vehicle systems. The controls for the DIC are located on the turn signal lever. For more information, see Steering Wheel Controls on page 5‑2.
In Brief SET/CLR: Use this button to set or clear the menu item when it is displayed. Cruise Control 1-15 SET/−: Move the thumbwheel down to set a speed or to make the vehicle decelerate. For more information, see Driver Information Center (DIC) on page 5‑21. See Cruise Control on page 9‑36. Vehicle Personalization Ultrasonic Rear Parking Assist (URPA) uses sensors on the rear bumper to detect objects while parking the vehicle. It operates at speeds less than 8 km/h (5 mph).
1-16 In Brief Power Outlets Sunroof The accessory power outlets can be used to plug in electrical equipment, such as a cell phone, an MP3 player, etc. There are two accessory power outlets. One is located inside the center console storage and the other is on the rear of the center floor console. To automatically tilt or close the sunroof with the safety function enabled, press the tilt open or close sunroof switch (B). Open the protective cover to use the accessory power outlet.
In Brief Performance and Maintenance Traction Control System (TCS) The vehicle may have a traction control system that limits wheel spin. The system turns on automatically every time the vehicle is started. . To turn off traction control, press and release d located on the instrument panel. i illuminates and the appropriate DIC message is displayed. See Ride Control System Messages on page 5‑27. . Press and release the button again to turn on traction control.
1-18 In Brief During cooler conditions, the low tire pressure warning light may appear when the vehicle is first started and then turn off. This may be an early indicator that the tire pressures are getting low and the tires need to be inflated to the proper pressure. The TPMS does not replace normal monthly tire maintenance. It is the driver’s responsibility to maintain correct tire pressures. See Tire Pressure Monitor System on page 10‑48 and Tire Pressure Monitor Operation on page 10‑49.
In Brief . Replace the vehicle's tires with the same TPC Spec number molded into the tire's sidewall near the size. Roadside Assistance and OnStar Roadside Assistance Program If you have a current OnStar subscription, press the OnStar button and the current GPS location will be sent to an OnStar Advisor who will assess your problem, contact Roadside Assistance, and relay your exact location to get the help you need. U.S.
1-20 In Brief How OnStar Service Works Q : This blue button connects you to a specially trained OnStar Advisor to verify your account information and to answer questions. ] : Press this red emergency button to get priority help from specially trained OnStar Emergency Advisors. X : Press this button for hands‐free, voice‐activated calling and to give voice commands for Hands‐Free Calling and Turn‐by‐Turn Navigation.
In Brief If you try to add, connect or modify any equipment or software in your vehicle, OnStar service may not work. Other problems OnStar can’t control may prevent service to you, such as hills, tall buildings, tunnels, weather, electrical system design and architecture of your vehicle, damage to important parts of your vehicle in a crash, or wireless phone network congestion or jamming.
1-22 In Brief 2 NOTES
Keys, Doors and Windows Keys, Doors and Windows Doors Keys . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . Remote Keyless Entry (RKE) System Operation . . . . . . . . . . . Door Locks . . . . . . . . . . . . . . . . . . . Power Door Locks . . . . . . . . . . . . Safety Locks . . . . . . . . . . . . . . . . . . Interior Mirrors Trunk . . . . . . . . . . . . . . . . . . . . . . . . .
2-2 Keys, Doors and Windows Keys and Locks Keys { WARNING Leaving children in a vehicle with the ignition key is dangerous for many reasons. Children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window. Do not leave the keys in a vehicle with children.
Keys, Doors and Windows 2-3 Remote Keyless Entry (RKE) System Remote Keyless Entry (RKE) System Operation indicate locking; see “Remote Lock Feedback” under Vehicle Personalization on page 5‑29. See Radio Frequency Statement on page 13‑15 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310. The RKE transmitter will work up to 20 m (65 ft) away from the vehicle. The fuel door will be locked when the doors are locked.
2-4 Keys, Doors and Windows Pressing K may also disarm the theft-deterrent system. See Anti-Theft Alarm System on page 2‑8. V (Remote Trunk Release): Press and hold V to open the trunk. 7 (Vehicle Locator/Panic Alarm): Press and release one time to locate the vehicle. The exterior lamps flash and the horn chirps. Press and hold 7 for at least two seconds to sound the panic alarm.
Keys, Doors and Windows WARNING (Continued) . Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. To lock and unlock the door, use the Remote Keyless Entry (RKE) transmitter or the key from the outside, and the door lock knob or switch from the inside. To unlock or lock the fuel door, use the RKE transmitter or the door lock switch from the inside.
2-6 Keys, Doors and Windows Safety Locks Power Safety Locks Manual Safety Locks Press v to activate the safety locks on the rear doors. The LED will illuminate. Open the rear doors to access the safety locks on the inside edge of each door. To manually set the locks, insert a key into the slot and turn it to the horizontal position. the door can only be opened from the outside with the door unlocked. To return the door to normal operation, turn the slot to the vertical position.
Keys, Doors and Windows Doors WARNING (Continued) Trunk . Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting. See Climate Control System in the Index. . If the vehicle has a power liftgate, disable the power liftgate function. { WARNING Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate.
2-8 Keys, Doors and Windows vehicles, the release handle can be accessed by folding the rear seat center seatback. See Rear Seats on page 3‑7. Pull the release handle to open the trunk from the inside. Rear Seat Pass-Through Lower the rear seat armrest to access the pass-through door. Pull the release handle to open the door. To close, push and latch the door. The vehicle may have a lock knob on the pass-through door. Turn the lock knob from the trunk side of the door to lock or unlock the door.
Keys, Doors and Windows Immobilizer Operation Disarming the System To disarm the system press the RKE transmitter. 2-9 K on Turning off the System Alarm If there is an attempt to open the doors, trunk, or hood without first pressing K on the transmitter or unlocking the driver's door with the key, the system alarm will be activated. The exterior lamps will flash and the horn will sound for about 30 seconds. To turn off the system alarm press Q or K on the RKE transmitter.
2-10 Keys, Doors and Windows If the engine still does not start, and the key appears to be undamaged or the light continues to stay on, try another ignition key. If the engine does not start with the other key, the vehicle needs service. If the vehicle does start, the first key may be damaged. See your dealer who can service the theft-deterrent system and have a new key made. Do not leave the key or device that disarms or deactivates the theft-deterrent system in the vehicle.
Keys, Doors and Windows Folding Mirrors Manual Foldaway Mirrors The vehicle has manual folding mirrors. These mirrors can be folded inward to prevent damage when going through an automatic car wash. To fold, pull the mirror toward the vehicle. Push the mirror outward, to return it to the original position. Heated Mirrors For vehicles with heated mirrors: < (Rear Window Defogger): Press to heat the mirrors.
2-12 Keys, Doors and Windows Power Windows Windows { WARNING Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. The vehicle aerodynamics are designed to improve fuel economy performance.
Keys, Doors and Windows Express Window Operation Windows with an express-up or down feature allow the front windows to be lowered or raised without holding the switch. Rear windows only have express down. Pull a window switch up or push it down all the way, release it, and the window goes down or up automatically. Stop the window by pushing or pulling the switch. Rear Window Lockout with Power Safety Locks 2-13 The light on the button goes out.
2-14 Keys, Doors and Windows the lockout feature is active. To restore power to the rear windows, press the button again. The light on the button goes out. If the light flashes, the feature may not be working properly. Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or is not working, you will need to reprogram each front power window for the express-up feature to work. Before reprogramming, replace or recharge the vehicle's battery.
Keys, Doors and Windows Roof Sunroof To open or close the sunroof, press the open or close sunroof switch (A) to the first detent position. To automatically open or close the sunroof with the safety function enabled, press the open or close sunroof switch (A) to the second detent position and release. To stop the movement, press the switch again. To automatically tilt or close the sunroof, press the tilt open or close sunroof switch (B).
2-16 Keys, Doors and Windows Sunshade Initializing the Sunroof Relearning the Safety Function The sunshade is manually operated. Close or open the sunshade by sliding. When the sunroof is opened, the sunshade is always open. If the sunroof cannot be closed, such as after disconnecting the vehicle battery, activate the sunroof electronics: If the sunroof does not close correctly after initializing: .
Seats and Restraints Seats and Restraints Safety Belt Extender . . . . . . . . . Safety System Check . . . . . . . . Safety Belt Care . . . . . . . . . . . . . Replacing Safety Belt System Parts After a Crash . . . . . . . . . Head Restraints Head Restraints . . . . . . . . . . . . . . . 3-2 Front Seats Seat Adjustment . . . . . . . . . . . . . . Power Seat Adjustment . . . . . . . Lumbar Adjustment . . . . . . . . . . . Reclining Seatbacks . . . . . . . . . . Heated Front Seats . . . . . . . . . . .
3-2 Seats and Restraints Front Seat Head Restraints The vehicle's front seats have adjustable head restraints in the outboard seating positions. The vehicle's rear seats have adjustable head restraints in the outboard seating positions. { WARNING With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.
Seats and Restraints Rear Seat Pull the head restraint up to raise it. To lower the head restraint, press the release button, located on the head restraint post on the top of the seatback, while you push the head restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
3-4 Seats and Restraints Front Seats Seat Adjustment Manual Seat Adjustment WARNING (Continued) Power Seat Adjustment pedal when you do not want to. Adjust the driver seat only when the vehicle is not moving. To adjust the seat position: 1. Pull the handle located at the front of the seat. 2. Move the seat forward or backward to adjust the seat position. 3. Release the handle to stop the seat from moving. To adjust a power seat, do any of the following: .
Seats and Restraints Lumbar Adjustment Reclining Seatbacks { WARNING You can lose control of the vehicle if you try to adjust the seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving. To increase or decrease lumbar support, press and hold the front or rear of the round control knob.
3-6 Seats and Restraints Manual Reclining Seatbacks To return the seatback to an upright position: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked. Power Reclining Seatbacks On vehicles with power reclining seatbacks, the vertical control is located on the outboard side of the seat. . To recline the seatback, press the control toward the rear of the vehicle. .
Seats and Restraints WARNING (Continued) heat, such as a blanket, cushion, cover or similar item. This may cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat. Press the button to heat the seat cushion and seatback. Indicator lights on the climate control display show the current setting. There are three temperature settings: . High = three lights . Medium = two lights .
3-8 Seats and Restraints To raise the seatback: 1. Push the seatback up and push it back to lock it into place. Make sure the safety belt is in the retainer clip and does not get twisted or caught in the seatback. 2. The seat handle tab will lock down when secured. 2. Pull on the lever located on the top of the seatback to unlock it. 3. Fold the seatback down. 3. Push and pull the top of the seatback to be sure it is locked into position.
Seats and Restraints { WARNING It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. This vehicle has indicators as a reminder to buckle the safety belts.
3-10 Seats and Restraints or the instrument panel... Put someone on it. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Get it up to speed. Then stop the vehicle. The rider does not stop.
Seats and Restraints Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted. And you can unbuckle a safety belt, even if you are upside down.
3-12 Seats and Restraints First, before you or your passenger(s) wear a safety belt, there is important information you should know. shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt locks if there is a sudden stop or crash. Q: What is wrong with this? { WARNING You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Seats and Restraints 3-13 { WARNING { WARNING { WARNING You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs. You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen.
3-14 Seats and Restraints Q: What is wrong with this? WARNING (Continued) { WARNING belt would apply too much force to the ribs, which are not as strong as shoulder bones. You could also severely injure internal organs like your liver or spleen. The shoulder belt should go over the shoulder and across the chest. You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt.
Seats and Restraints Q: What is wrong with this? Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 3-15 The lap-shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
3-16 Seats and Restraints Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 3‑21. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See “Shoulder Belt Height Adjuster” later in this section for instructions on use and important safety information. 4.
Seats and Restraints Adjust the height so the shoulder portion of the belt is on the shoulder and not falling off of it. The belt should be close to, but not contacting, the neck. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. See How to Wear Safety Belts Properly on page 3‑11. the desired position, try to move it down without pushing the release button to make sure it has locked into position.
3-18 Seats and Restraints Adjustable Safety Belt Comfort Guide On vehicles with the adjustable comfort guide, one guide is provided. Additional adjustable comfort guides are available through your dealer. To install the adjustable safety belt comfort guide to the seatback and the safety belt: 2. Attach the adjustable comfort guide to the anchor loop by threading the hook through the loop. 1. Locate the anchorage loop between the rear outboard seatback and seat bolster, near the top.
Seats and Restraints 4. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. 5. The elastic cord on the comfort guide is adjustable. You can make it longer or shorter by squeezing both ends of the plastic adjuster and pulling on the elastic cord or the guide. 3. Place the guide over the belt, and insert the two edges of the belt into the slots of the guide. 3-19 WARNING (Continued) seriously injured.
3-20 Seats and Restraints To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide. Un-hook the guide from the loop on the seat. Store the guide in a convenient place like the glove box for the next time it is needed. To install a comfort guide to the safety belt: 1. Remove the guide from its storage pocket on the side of the seat. Sewn‐in Safety Belt Comfort Guide 3. Be sure that the belt is not twisted and it lies flat.
Seats and Restraints WARNING (Continued) and across the chest. These parts of the body are best able to take belt restraining forces. To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide. Store the guide in its storage pocket on the side of the seatback. Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women.
3-22 Seats and Restraints use it for securing child seats. To wear it, attach it to the regular safety belt. For more information, see the instruction sheet that comes with the extender. Safety System Check Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job. See your dealer to have it repaired.
Seats and Restraints Airbag System The vehicle may have the following airbags: The vehicle has the following airbags: . . A frontal airbag for the driver. . A frontal airbag for the right front passenger. . A seat-mounted side impact airbag for the driver. . A seat-mounted side impact airbag for the right front passenger. . . A roof-rail airbag for the driver and the passenger seated directly behind the driver.
3-24 Seats and Restraints Here are the most important things to know about the airbag system: { WARNING You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them. Also, airbags are not designed to deploy in every crash. In some crashes safety belts are your only restraint. See When Should an Airbag Inflate? on page 3‑26.
Seats and Restraints 3-25 Where Are the Airbags? There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 5‑10 for more information. Driver Side Shown, Passenger Side Similar The driver frontal airbag is in the middle of the steering wheel.
3-26 Seats and Restraints WARNING (Continued) or even death. The path of an inflating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering. Rear Seat Driver Side Shown, Passenger Side Similar If the vehicle has second row seat‐mounted side impact airbags, they are in the sides of the rear seatback closest to the door.
Seats and Restraints Frontal airbags may inflate at different crash speeds. For example: . If the vehicle hits a stationary object, the airbags could inflate at a different crash speed than if the vehicle hits a moving object. . If the vehicle hits an object that deforms, the airbags could inflate at a different crash speed than if the vehicle hits an object that does not deform. . .
3-28 Seats and Restraints What Makes an Airbag Inflate? How Does an Airbag Restrain? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator. Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy. The inflator, the airbag, and related hardware are all part of the airbag module.
Seats and Restraints the windshield or being able to steer the vehicle, nor does it prevent people from leaving the vehicle. { WARNING When an airbag inflates, there may be dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so.
3-30 Seats and Restraints The words ON and OFF will be visible during the system check. When the system check is complete, either the word ON or the word OFF will be visible. See Passenger Airbag Status Indicator on page 5‑11. The passenger sensing system turns off the right front passenger frontal airbag and seat‐mounted side impact airbag under certain conditions. The driver airbags and the roof‐rail airbags are not affected by the passenger sensing system.
Seats and Restraints . The right front passenger seat is occupied by a smaller person, such as a child who has outgrown child restraints. . There is a critical problem with the airbag system or the passenger sensing system. WARNING (Continued) the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat.
3-32 Seats and Restraints If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers. 4.
Seats and Restraints enable the right front passenger frontal airbag and seat‐mounted side impact airbag: 1. Turn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers. 3. Place the seatback in the fully upright position. 4. Have the person sit upright in the seat, centered on the seat cushion, with legs comfortably extended. 5.
3-34 Seats and Restraints Servicing the Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Your dealer and the service manual have information about servicing the vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 13‑11.
Seats and Restraints passenger airbag(s). See Passenger Sensing System on page 3‑29. If you have questions, call Customer Assistance. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual. See Customer Satisfaction Procedure on page 13‑1. Q: Because I have a disability, I have to get my vehicle modified. How can I find out whether this will affect my airbag system? A: If you have questions, call Customer Assistance.
3-36 Seats and Restraints If the airbag readiness light stays on after the vehicle is started or comes on when you are driving, the airbag system may not work properly. Have the vehicle serviced right away. See Airbag Readiness Light on page 5‑10 for more information. Child Restraints Older Children The manufacturer's instructions that come with the booster seat state the weight and height limitations for that booster.
Seats and Restraints . Can proper safety belt fit be maintained for the length of the trip? If yes, continue. If no, return to the booster seat. Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. This applies belt force to the child's pelvic bones in a crash.
3-38 Seats and Restraints { WARNING { WARNING Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt. The child could move too far forward increasing the chance of head and neck injury. The child might also slide under the lap belt. The belt force would then be applied right on the abdomen.
Seats and Restraints { WARNING WARNING (Continued) Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 110 kg (240 lb) force on a person's arms. An infant should be secured in an appropriate restraint.
3-40 Seats and Restraints Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. For most basic types of child restraints, there are many different models available.
Seats and Restraints 3-41 Child Restraint Systems (B) Forward-Facing Child Seat (A) Rear‐Facing Infant Seat A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (B) provides restraint for the child's body with the harness.
3-42 Seats and Restraints Securing an Add-On Child Restraint in the Vehicle { WARNING A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle's safety belt or LATCH system, following the instructions that came with that child restraint and the instructions in this manual. To help reduce the chance of injury, the child restraint must be secured in the vehicle.
Seats and Restraints We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great if the airbag deploys.
3-44 Seats and Restraints Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in your vehicle — even when no child is in it. Lower Anchors and Tethers for Children (LATCH System) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier.
Seats and Restraints Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash. The child restraint may have a single tether (A) or a dual tether (C).
3-46 Seats and Restraints According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. See Where to Put the Restraint on page 3‑42 for additional information. To assist you in locating the lower anchors, each rear anchor position has a label, near the crease between the seatback and the seat cushion.
Seats and Restraints WARNING (Continued) that came with the child restraint and the instructions in this manual. { WARNING Do not attach more than one child restraint to a single anchor. Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured. To reduce the risk of serious or fatal injuries during a crash, attach only one child restraint per anchor.
3-48 Seats and Restraints A. Passenger Side Rear Seating Position and Lower Anchors 1 and 2 B. Center Rear Seating Position and Lower Anchors 3 and 4 C. Driver Side Rear Seating Position and Lower Anchors 4 and 5 There are five lower LATCH anchors in the rear seat. . Use anchors 1 and 2 when installing a child restraint using LATCH in seating position A. . Use anchors 3 and 4 when installing a child restraint using LATCH in seating position B. .
Seats and Restraints 2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 3-49 2.2. Route, attach, and tighten the top tether according to the child restraint instructions and the following instructions: 2.1. Find the top tether anchor. Open the cover to expose the anchor. . .
3-50 Seats and Restraints Head Restraint Removal and Reinstallation The rear outboard head restraints can be removed if they interfere with the proper installation of the child restraint. To remove the head restraint: . If the position you are using has an adjustable headrest or head restraint and you are using a single tether, route the tether under the headrest or head restraint and in between the headrest or head restraint posts. See Head Restraints on page 3‑2. .
Seats and Restraints 2. Press both buttons on the head restraint posts at the same time, and pull up on the head restraint. To reinstall the head restraint: Replacing LATCH System Parts After a Crash { WARNING 3. Store the head restraint in the trunk of the vehicle. 4. When the child restraint is removed, reinstall the head restraint before the seating position is used.
3-52 Seats and Restraints Securing Child Restraints (Rear Seat) When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑44 for how and where to install the child restraint using LATCH.
Seats and Restraints 3-53 6. If the child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH System) on page 3‑44 for more information. 4. Pull the shoulder belt all the way out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor. 5.
3-54 Seats and Restraints and Tethers for Children (LATCH System) on page 3‑44 for additional information on installing the head restraint properly. Securing Child Restraints (Front Passenger Seat) This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 3‑42.
Seats and Restraints Anchors and Tethers for Children (LATCH System) on page 3‑44 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
3-56 Seats and Restraints 7. Before placing a child in the child restraint, make sure it is securely held in place. To check, grasp the child restraint at the safety belt path and attempt to move it side‐to‐side and back‐ and‐forth. When the child restraint is properly installed, there should be no more than 2.5 cm (1 in) of movement. 5. Pull the shoulder belt all the way out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor.
Storage Storage Storage Compartments Storage Compartments Instrument Panel Storage . . . . Glove Box . . . . . . . . . . . . . . . . . . . . Cupholders . . . . . . . . . . . . . . . . . . . Rear Storage . . . . . . . . . . . . . . . . . Center Console Storage . . . . . . 4-1 4-1 4-2 4-2 4-2 Instrument Panel Storage Additional Storage Features Cargo Net . . . . . . . . . . . . . . . . . . . . . 4-3 Convenience Net . . . . . . . . . . . . .
4-2 Storage Cupholders Rear Storage Center Console Storage Pull down the armrest. Push the button to lift the cover. Close the cover before folding the armrest up. Push the button (A) to access the storage area under the armrest. Two cupholders are in the center console. Cupholders may be located in the second row seat armrest. To access, pull the armrest down.
Storage Additional Storage Features Convenience Net Cargo Net There is a cargo net for storing items on the side of the vehicle's trunk. For vehicles with a convenience net, it is located in the trunk and used to store small loads. The net should not be used to store heavy loads. Attach the loops on each side of the net to the hooks located on the sides of the trunk.
4-4 Storage 2 NOTES
Instruments and Controls Instruments and Controls Controls Steering Wheel Adjustment . . . 5-2 Steering Wheel Controls . . . . . . 5-2 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Windshield Wiper/Washer . . . . . 5-3 Compass . . . . . . . . . . . . . . . . . . . . . 5-4 Clock . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Power Outlets . . . . . . . . . . . . . . . . . 5-5 Warning Lights, Gauges, and Indicators Warning Lights, Gauges, and Indicators . . . . . . . . . . . . . . . .
5-2 Instruments and Controls Controls Steering Wheel Controls Steering Wheel Adjustment page 7‑33, the Onstar Owner's Guide, or the separate Navigation System Manual for more information. $ c (Mute / End Call): Press to silence the vehicle speakers only. Press again to turn the sound on. For vehicles with OnStar or Bluetooth systems, press to reject an incoming call, or end a current call. _ SRC ^ (Rotary Control): Press to select an audio source. To adjust the steering wheel: 1. Pull the lever down.
Instruments and Controls Windshield Wiper/Washer 5-3 & (Adjustable Interval Wipes): Wipe Parking Turn the band up for more frequent wipes or down for less frequent wipes. If the ignition is turned to LOCK/ OFF while the wipers are on 1, 2, or &, they will immediately stop. If the windshield wiper lever is then moved to OFF before the driver door is opened, or within 10 minutes, the wipers will restart and move to the base of the windshield. 9 (Off): Turns the windshield wipers off.
5-4 Instruments and Controls windshield washer had been activated. See Washer Fluid on page 10‑22 for information on filling the windshield washer fluid reservoir. { WARNING In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. Compass The vehicle may have a compass display on the Driver Information Center (DIC).
Instruments and Controls Setting the Month and Day Format 2. Highlight Month & Day format. Certain electrical accessories may not be compatible with the accessory power outlets and could overload vehicle or adapter fuses. If a problem is experienced, see your dealer. 3. Press the Z knob to select DD/MM/YYYY (day/month/year), MM/DD/YYYY (month/day/year), or YYYY/MM/DD (year/month/ day) display format.
5-6 Instruments and Controls turns off. To reset the circuit, unplug the item and plug it back in or turn the Remote Accessory Power (RAP) off and then back on. See Retained Accessory Power (RAP) on page 9‑18. Prolonged usage of the power outlet at the maximum load of 150 watts, may cause the outlet to overheat and automatically shutdown. The power restarts when equipment that operates within the limit is plugged into the outlet and a system fault is not detected.
Instruments and Controls Instrument Cluster English Automatic Transmission Shown, Metric Similar 5-7
5-8 Instruments and Controls Speedometer Trip Odometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph). The trip odometer can show how far the vehicle has been driven since the trip odometer was last reset. Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper‐resistant odometer. The digital odometer will read 999,999 if it is turned back.
Instruments and Controls Here are four things that some owners ask about. None of these show a problem with the fuel gauge: . At the service station, the fuel pump shuts off before the gauge reads full. . It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge may have indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. . The gauge moves a little while turning a corner or speeding up. .
5-10 Instruments and Controls Safety Belt Reminders Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument panel cluster. When the engine is started this light begins to flash and a chime comes on for several seconds to remind the driver to fasten their safety belt. The light also stays on if the driver remains unbuckled. This cycle repeats if the driver is unbuckled while the vehicle is moving.
Instruments and Controls turned off the right front passenger frontal airbag and seat-mounted side impact airbag. { WARNING If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.
5-12 Instruments and Controls Charging System Light The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. The light turns off when the engine is started. If it does not, have the vehicle serviced by your dealer. If the light stays on, or comes on while driving, there could be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery.
Instruments and Controls costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/ Maintenance test. See Accessories and Modifications on page 10‑3. This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required.
5-14 Instruments and Controls diagnostic tools to fix any mechanical or electrical problems that might have developed. The vehicle may not pass inspection if: . Emissions Inspection and Maintenance Programs Some state/provincial and local governments may have programs to inspect the on-vehicle emission control equipment. For the inspection, the emission system test equipment is connected to the vehicle’s Data Link Connector (DLC). The DLC is under the instrument panel to the left of the steering wheel.
Instruments and Controls { WARNING The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service. If the light comes on while driving, a chime sounds. Pull off the road and stop. The pedal might be harder to push or go closer to the floor. It might also take longer to stop.
5-16 Instruments and Controls Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. A chime may also sound when the light comes on steady.
Instruments and Controls See Traction Control System (TCS) on page 9‑31 and Electronic Stability Control (ESC) on page 9‑33 for more information. Electronic Stability Control (ESC) Off Light This light comes on when the Electronic Stability Control (ESC) system is turned off. If the Traction Control System (TCS) is off, wheel spin is not limited. If the ESC is off, the system does not assist in controlling the vehicle. Turn on the TCS and the ESC and the warning light turns off.
5-18 Instruments and Controls See Electronic Stability Control (ESC) on page 9‑33 and Traction Control System (TCS) on page 9‑31 for more information. When the Light is On Steady See Ride Control System Messages on page 5‑27 for more information on the messages associated with this light. A tire pressure message can accompany the light. See Tire Messages on page 5‑28 for more information.
Instruments and Controls Low Fuel Warning Light The oil pressure light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer. 5-19 Security Light The immobilizer light should come on briefly as the engine is started.
5-20 Instruments and Controls High-Beam on Light Fog Lamp Light Cruise Control Light The high-beam on light comes on when the high-beam headlamps are in use. For vehicles with fog lamps, this light comes on when the fog lamps are in use. See Headlamp High/Low-Beam Changer on page 6‑2 for more information. The light goes out when the fog lamps are turned off. See Fog Lamps on page 6‑4 for more information.
Instruments and Controls Information Displays Driver Information Center (DIC) The Driver Information Center (DIC) displays information about the vehicle. It also displays warning messages if a system problem is detected. See Vehicle Messages on page 5‑24 for more information. All messages appear in the DIC display located in the center of the instrument panel cluster. On some models, the DIC may have some warning lights or indicators shown in the top portion of the display.
5-22 Instruments and Controls Trip/Fuel Menu Items Fuel Range Press MENU on the turn signal lever until Trip/Fuel Information Menu is displayed. Use w x to scroll through the following menu items: . Trip 1 . Trip 2 This display shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Fuel range cannot be reset. .
Instruments and Controls which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR. Digital Speedometer The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset. Turn-by-Turn This display is used for the Navigation System Turn-by-Turn guidance.
5-24 Instruments and Controls Remember, the Remaining Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Remaining Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the Engine Oil Life System press SET/ CLR while the Remaining Oil Life display is active. See Engine Oil Life System on page 10‑12.
Instruments and Controls Press Brake Pedal To Release Park Brake This message is displayed if you attempt to release the electric parking brake without the brake pedal applied. See Parking Brake on page 9‑29 for more information. Release Park Brake Switch This message is displayed if the electric parking brake is on while the vehicle is in motion. Release it before you attempt to drive. See Parking Brake on page 9‑29 for more information.
5-26 Instruments and Controls When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. Coolant Level Low Add Coolant This message will display if the coolant is low; see Engine Coolant on page 10‑16. Engine Overheated — Idle Engine This message displays when the engine coolant temperature is too hot.
Instruments and Controls Engine Power Messages Key and Lock Messages Engine Power Is Reduced Replace Battery In Remote Key This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven.
5-28 Instruments and Controls Sport Mode On Tire Messages Transmission Messages This message displays when using the interactive drive control. See Interactive Drive Control System on page 9‑34 for more information. Check XXX Tire Pressure or Add Air To Tire Service Transmission Traction Control Off This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly.
Instruments and Controls Window Messages Open, Then Close Driver Window This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to reprogram each front window for the express up feature to work. See Power Windows on page 2‑12 for more information. Open, Then Close Passenger Window This message is displayed when the window needs to be reprogrammed.
5-30 Instruments and Controls Climate and Air Quality Air Conditioning Mode Select the Climate and Air Quality menu and the following will be displayed: This allows selection of automatic start of the air conditioning upon vehicle start. Selecting On indicates the air conditioning will be on when the vehicle is started. Selecting Off turns the air conditioning off each time the vehicle is started. Last Setting will resume the last setting when the vehicle was shut off. . Auto Fan Speed .
Instruments and Controls 5-31 Auto Rear Defog Collision/Detection Systems Lighting This allows the auto rear defog to be turned on or off. This feature will automatically turn on the rear defogger when it is cold outside. Select the Collision/Detection Systems menu and Park Assist will be displayed. Select the Lighting menu and the following will be displayed: Press the MENU/SELECT knob when Auto Rear Defog is highlighted to select On or Off.
5-32 Instruments and Controls Power Door Locks Auto Door Unlock Select Power Door Locks and the following will be displayed: This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park). . Unlocked Door Anti Lock Out . Auto Door Unlock . Delayed Door Lock Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open.
Instruments and Controls 5-33 Remote Lock Feedback Remote Door Unlock Return to Factory Settings This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. This allows selection of which doors will unlock when pressing the unlock button on the RKE transmitter. Press the MENU/SELECT knob when Remote Lock Feedback is highlighted. Turn the knob to select Lights and Horn, Lights Only, Horn Only, or Off.
5-34 Instruments and Controls 2 NOTES
Lighting Lighting Exterior Lighting Exterior Lamp Controls . . . . . . . . 6-1 Exterior Lamps Off Reminder . . . . . . . . . . . . . . . . . . . . 6-2 Headlamp High/Low-Beam Changer . . . . . . . . . . . . . . . . . . . . . 6-2 Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2 Daytime Running Lamps (DRL) . . . . . . . . . . . . . . . . 6-2 Automatic Headlamp System . . . . . . . . . . . . . . . . . . . . . . 6-3 Hazard Warning Flashers . . . . . 6-3 Turn and Lane-Change Signals . . . . . . . . . . . . .
6-2 Lighting 2 (Headlamps): Turns on the headlamps together with the following: . Sidemarker Lamps . Taillamps . License Plate Lamps . Instrument Panel Lights . Parking Lamps Headlamp High/ Low-Beam Changer 2 3 Headlamp High/Low Beam Changer: Push the turn signal/lane change lever away from you and release, to turn the high beams on. To return to low beams, push the lever again or pull it toward you and release.
Lighting When the DRL are on, the low-beam headlamps will be on. The taillamps, sidemarker, instrument panel lights and other lamps will not be on. The DRL turn off when the headlamps are turned to O or the ignition is off. Automatic Headlamp System When the exterior lamp control is set to AUTO and it is dark enough outside, the headlamps come on automatically. There is a light sensor located on top of the instrument panel. Do not cover the sensor.
6-4 Lighting Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is completed. If the lever is briefly pressed and released, the turn signal flashes three times. Fog Lamps Some localities have laws that require the headlamps to be on along with the fog lamps. The turn and lane‐change signal can be turned off manually by moving the lever back to its original position.
Lighting Interior Lighting Dome Lamps Reading Lamps Instrument Panel Illumination Control The interior lamps control located in the overhead console controls both the front and rear interior lamps. There are front and rear reading lamps. To operate: 6-5 The front reading lamps are located in the overhead console. * (Off): Turns the lamps off. 1 (Door): Turns the lamps on when any door is opened. + (On): Keeps the lamps on all the time.
6-6 Lighting Lighting Features Entry Lighting The headlamps, taillamps, license plate lamps, reverse lamps, dome lamps, and most of the interior lights turn on briefly, when the Remote Keyless Entry (RKE) K is pressed. See Remote Keyless Entry (RKE) System Operation on page 2‑3. When the drivers door is opened, all control lights, Driver Information Center (DIC) and door pocket lights turn on.
Infotainment System Infotainment System Introduction For more information, see Defensive Driving on page 9‑2. Read the following pages to become familiar with the audio system's features. Notice: Contact your dealer before adding any equipment. Introduction { WARNING Introduction . . . . . . . . . . . . . . . . . . . 7-1 Theft-Deterrent Feature . . . . . . . 7-2 Overview . . . . . . . . . . . . . . . . . . . . . . 7-2 Operation . . . . . . . . . . . . . . . . . . . . .
7-2 Infotainment System Theft-Deterrent Feature Overview The theft-deterrent feature works by learning a portion of the Vehicle Identification Number (VIN) to the infotainment system. The infotainment system does not operate if it is stolen or moved to a different vehicle. A. RADIO / BAND . Changes the band while listening to the radio. . Selects the radio when listening to a different audio source. B. CD/AUX . Selects the CD player or an external audio source.
Infotainment System C. s © . . H. FAV 1/2/3 . Radio: Seeks the previous station. CD: Select the previous track or rewinds within a track. I. E. . F. Radio: Seeks the next station. CD: Selects the next track or fast forwards within a track. J. . Turns the system on or off and adjusts the volume. G. Buttons 1 to 6 . Radio: Saves and selects favorite stations. L. Radio: Shows available information about the current station. CD: Shows available information about the current track.
7-4 Infotainment System Operation Controls The infotainment system is operated by using the pushbuttons, multifunction knobs, menus shown on the display, and steering wheel controls, if equipped. Turning the System On or Off 3 O (Volume/Power): Press to turn the system on and off. For vehicles without OnStar®, press V / $ to mute the infotainment system. To cancel mute, press V / $ again, or turn the 3 O knob. Menu System Controls The Z knob and the BACK button are used to navigate the menu system.
Infotainment System 7-5 Submenus Setting a Value Entering a Character Sequence An arrow on the right‐hand edge of the menu indicates that it has a submenu with other options. 1. Turn the Z knob to change the current value of the setting. 1. Turn the Z knob to highlight the character. 2. Press the Z knob to confirm the setting. 2. Press the Z knob to select the character.
7-6 Infotainment System 3. Press and hold the Z knob until the value changes to 0. Adjusting the Fader and Balance Press the BACK button to go back to the Tone Settings menu. Press the BACK button to go back to the Tone Settings menu. System Settings Adjusting the Treble, Midrange, and Bass The auto volume feature automatically adjusts the radio volume to compensate for road and wind noise as the vehicle speeds up or slows down, so that the volume level is consistent. Auto Volume 1.
Infotainment System 5. Press the BACK button to go back to the System Configuration menu. Configuring the Number of Favorites Pages Control Buttons The maximum volume played when the radio is first turned on can be set. The buttons used to control the radio are: To configure the number of available favorites pages: RADIO/BAND: Press to turn the radio on and choose between AM, FM, and XM™, if equipped. 1. Press the CONFIG button. Z (Menu Knob): 2. Select Radio Settings. 2. Select Radio Settings. 3.
7-8 Infotainment System AS 1/2: Press to open the autostore list and select auto store pages. RDS (Radio Data System) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information. This feature only works when the information from the radio station is available. In rare cases, a radio station could broadcast incorrect information that causes the radio features to work improperly. If this happens, contact the radio station.
Infotainment System To search for a programming type determined by station: 1. Press the Z knob. To cancel the station search, press the Z knob. Storing a Station as a Favorite 2. Select FM Category List. A list of all programming types available displays. Stations from all bands can be stored in any order in the favorite pages. 3. Select the programming type. A list of stations that transmit programming of the selected type displays.
7-10 Infotainment System Satellite Radio Control Buttons Selecting the XM Band Vehicles with an XM™ Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. The buttons used to control the XM radio are: RADIO/BAND: Press to turn the radio on and choose between AM, FM, and XM™, if equipped. Press the RADIO/BAND button to choose between the AM, FM, and XM bands. The last channel played in that band begins to play when that band is selected.
Infotainment System XM channels can be selected by station lists or category lists. 2. Press the Z knob to select the channel, or leave the channel highlighted. Selecting a Channel by Station List To select an XM channel using the menu: XM channels can be selected by using s ©, ¨ \, or the Z knob. 1. Press the Selecting an XM Channel To select an XM channel using s © or ¨ \, do one of the following: . . Press and release s © or ¨ \ to go to the previous or next channel.
7-12 Infotainment System Loading XM: The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly. Channel Off Air: This channel is not currently in service. Tune in to another channel. Channel Unauth : This channel is blocked or cannot be received with your XM Subscription package. Channel Unavailable: This previously assigned channel is no longer assigned. Tune to another station. No Artist Info: The system is working properly.
Infotainment System 7-13 static can occur, especially around tall buildings or hills, causing the sound to fade in and out. under heavy foliage, bridges, garages, or tunnels may cause loss of the XM signal for a period of time. reception, the antenna connector needs to be properly attached to the post on the glass. AM Cellular Phone Usage The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other.
7-14 Infotainment System Notice: Do not apply aftermarket glass tinting with metallic film. The metallic film in some tinting materials will interfere with or distort the incoming radio reception. Any damage caused to your backglass antenna due to metallic tinting materials will not be covered by the vehicle warranty. Audio Players Satellite Radio Antenna Sound quality can be reduced due to disc quality, recording method, quality of the music recorded, and disc handling.
Infotainment System Control Buttons The buttons used to control the CD player are: CD/AUX: Press to use the CD player. s ©/¨ \: Press to select tracks or to fast rewind or forward within a track. If the disc is not removed after it is ejected, it is pulled back in after a few seconds. Playing a CD or MP3 CD Press the CD/AUX button if there is a disc in the player; it begins playing. INFO: Press to display additional information about the current track that may be available.
7-16 Infotainment System Searching for MP3 Tracks Auxiliary Devices The search feature may take some time to display the information after reading the disc due to the amount of information stored on the disc. FM automatically plays while the disc is being read. This vehicle may have an 3.5 mm (1/8 in) auxiliary input jack and a USB port, located in the center console. Some portable audio devices such as iPods®, MP3 players, and USB storage devices can be connected to the vehicle using a 3.
Infotainment System USB Port For vehicles with a USB port, the following devices may be connected and controlled by the infotainment system. . iPods . PlaysForSure Devices (PFD) . USB Drives . Zunes Not all iPods, PFDs, USB Drives, and Zunes are compatible with the infotainment system. Connecting and Controlling an iPod® Not all iPods can be controlled by the infotainment system. Connecting an iPod Connect the iPod to the USB port. Searching for a Track Tracks can be searched for by: .
7-18 Infotainment System . Song Titles . Podcasts . Genres To search for tracks: 1. Press the Z knob. Repeat On: Repeats the current track. Repeat Off: Starts playing from the beginning of the current track after the last track finishes. 2. Select Search. Connecting and Controlling a USB Drive 3. Select: Playlists, Artists, Albums, Song Titles, Podcasts, or Genres. The infotainment system can only play back .mp3 and .wma files from a USB drive. 4. Select the track.
Infotainment System 3. Select: Playlists, Artists, Albums, Song Titles, Genres, or Folder View. 4. Select the track. Shuffle Press the Z knob and set Shuffle Songs (Random) to On or Off. On: Plays current tracks in random order. Off: Plays current tracks in sequential order. Repeat Press the Z knob and set Repeat to On or Off. Repeat On: Repeats the current track. Repeat Off: Starts playing from the beginning of the current track after the last track finishes.
7-20 Infotainment System When to Speak: A tone sounds to indicate that the system is ready for a voice command. Wait for the tone and then speak. How to Speak: Speak clearly in a calm and natural voice. Audio System When using the Bluetooth system, sound comes through the vehicle's front audio system speakers and overrides the audio system. Use the 3 O knob during a call to change the volume level. The adjusted volume level remains in memory for later calls. The system maintains a minimum volume level.
Infotainment System Pairing a Phone 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select Bluetooth. 4. Select Pair Device (Phone). A four‐digit Personal Identification Number (PIN) number appears on the display. If the “Add new GPS device” option is selected, the system will start a search for Bluetooth “Handsfree” profile devices just like if “Add new Phone” was selected.
7-22 Infotainment System Making a Call 1. Press the V / $ button twice. 2. Enter the character sequence. See “Entering a Character Sequence” in Operation on page 7‑4 for more information. 3. Select Call to start dialing the number. Accepting or Declining a Call When a call is received, the infotainment system mutes and a ring tone is heard in the vehicle. Accepting a Call Turn the Z knob to Answer and press the Z knob. Declining a Call Turn the Z knob to Decline and press the Z knob.
Infotainment System Dual Tone Multi-Frequency (DTMF) Tones The in‐vehicle Bluetooth system can send numbers during a call. This is used when calling a menu‐driven phone system. 1. Press the Z knob and select Enter Number. 2. Enter the character sequence; see “Entering a Character Sequence” in Operation on page 7‑4 for more information. Bluetooth (Voice Recognition) Pairing A Bluetooth‐enabled cell phone must be paired to the Bluetooth system and then connected to the vehicle before it can be used.
7-24 Infotainment System 4. Start the pairing process on the cell phone that will be paired to the vehicle. Reference the cell phone manufacturer's user guide for information on this process. Locate the device named “General Motors” or “Your Vehicle” in the list on the cell phone and follow the instructions on the cell phone to enter the four‐digit PIN that was provided in Step 3. 5. The system prompts for a name for the phone. This name will be used to indicate which phone is connected.
Infotainment System 4. Say the name of the phone to be deleted. If the phone name is unknown, use the “List” command for a list of all paired phones. The system responds “Would you like to delete ? Yes or No,” followed by a tone. 2. Say “Bluetooth.” The system responds “Bluetooth ready,” followed by a tone. 3. Say “Change phone.” The system responds “Please wait while I search for other phones.” 5. Say “Yes” to delete the phone. The system responds “OK, deleting .
7-26 . Infotainment System If the system does not recognize the phone number, the response is “Store .” “Please say yes or no.” If the number is correct, say “Yes.” If the number is not correct, say “No.” The system will ask for the number again. the number is stored, the system returns to the main menu. Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually. 1. Press 4.
Infotainment System . If the name tag sounds correct, say “Yes” and the name tag is stored. After the number is stored, the system returns to the main menu. Using the Directory Command The directory command lists all of the name tags stored by the system. To use the directory command: 1. Press . . b g. For vehicles without a navigation system, the system responds “Ready,” followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone, say “Hands Free.
7-28 Infotainment System route destination directory. Are you sure you want to do this? Please say yes or no.” Using the Delete All Name Tags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar, if stored. . Say “Yes” to delete all name tags. . Say “No” to cancel the function and return to the main menu. To delete all name tags: 1. Press . . b g. For vehicles without a navigation system, the system responds “Ready,” followed by a tone.
Infotainment System not correct, say “No.” The system will ask for the number again. Using the Digit Dial Command 1. Press b g. 4. Continue entering digits until the number to be dialed is complete. After the entire number has been entered, say “Dial.” The system responds “OK, Dialing” and dials the number. . For vehicles without a navigation system, the system responds “Ready,” followed by a tone. . If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number.
7-30 Infotainment System Using the Re‐dial Command 1. Press . . b g. For vehicles without a navigation system, the system responds “Ready,” followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone, say “Hands Free.” The system responds “Ready,” followed by a tone. 2. After the tone, say “Re‐dial.” The system responds “Re‐dial using ” and dials the last number called from the connected Bluetooth phone.
Infotainment System Muting a Call During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. To Mute a call 1. Press b g. The system responds “Ready,” followed by a tone. 2. Say “Mute Call.” The system responds “Call muted.” To Cancel Mute 1. Press b g. The system responds “Ready,” followed by a tone. 2. After the tone, say “Mute Call.” The system responds “Resuming call.
7-32 Infotainment System “Hands Free.” The system responds “Ready,” followed by a tone. 2. Say “Bluetooth.” The system responds “Bluetooth ready,” followed by a tone. 3. Say “Voice.” The system responds “OK, accessing .” The cell phone's normal prompt messages will go through their cycle according to the phone's operating instructions. Dual Tone Multi-Frequency (DTMF) Tones The in‐vehicle Bluetooth system can send numbers and the numbers stored as name tags during a call.
Infotainment System 7-33 Clearing the System Bluetooth Pairing Pairing information: Unless information is deleted out of the in‐vehicle Bluetooth system, it will be retained indefinitely. This includes all saved name tags in the phone book and phone pairing information. For information on how to delete this information, see the previous sections on “Deleting a Paired Phone“ and “Deleting Name Tags.
7-34 Infotainment System location through the Bluetooth Serial Port Profile is not available. Pairing a Phone 1. Press the CONFIG control button repeatedly until the Phone menu is shown. 2. Select the Bluetooth submenu. 3. Select “Add New Phone.” The pairing process will begin searching for Bluetooth devices on your cellular pone. See the cell phone manufacturer's user guide for information on this process.
Infotainment System 7-35 system voice prompt then repeats the name you provided for confirmation: say “Yes.” 5. The system responds with “phone name has been successfully paired” after the pairing process is complete. Listing All Paired and Connected Phones 1. Press the CONFIG control button repeatedly until the Phone menu is shown. 2. Select the Bluetooth submenu. 3. Select the Device List submenu. A list of all previously paired phones will be displayed.
7-36 Infotainment System Deleting a Paired Phone 1. Press the CONFIG control button repeatedly until the Phone menu is shown. 3. Select the Device List submenu. 2. Select the Bluetooth submenu. 4. Select the phone to be deleted and then follow the on-screen prompts to delete the device from the system.
Infotainment System 5. Once a phone has been deleted, the only way to connect back to that phone is to pair the phone again. See “Pairing a Phone” earlier before the process is started. 2. Select the Bluetooth submenu. Linking to a Different Phone To link to a different phone, the new phone must be in the vehicle and available to be connected to the Bluetooth system before the process is started. 1. Press the CONFIG control button repeatedly until the Phone menu is shown. 3.
7-38 Infotainment System Making a Call Enter Number Press V located on the faceplate of the infotainment system, to access the phone menu. Use to enter a phone number and make a call. 1. Press the Enter Number selection. A dial pad displays. 5. The Phone menu will be displayed with the name of the phone linked. 2. Enter the phone number by pivoting the Multifunction knob. 3. Press the Call button on the screen to make the call.
Infotainment System Accepting or Declining an Incoming Call When an incoming call is received, the audio is muted and ring tone sounds. Accepting a Call Press b / g on the steering wheel control to answer an incoming call, or press the appropriate preset button for the Answer option on the screen to answer the call. 7-39 Declining a Call Press the $ / c on the steering wheel controls or select the Decline option on the screen.
7-40 Infotainment System Conference Calling Ending a Call Conference and three-way calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. To start a conference while in a current call: 1. Press the V control button on the faceplate until the Phone main screen is shown with the current active call. 3. Make another call. The first call will be placed on hold while the second call is dialing and connected. 4.
Infotainment System Mute or UnMute a Call 1. Press the V control button. 2. Select the Mute call. 3. Select the Mute call again to unmute the call. 7-41 Dual Tone Multi-Frequency (DTMF) Tones The in-vehicle Bluetooth system can send numbers during a call. This is used when calling a menu-driven phone system. 2. Select Enter Number option and enter the number sequence. The DTMF Tones will be generated on the network as you enter each number. 1. Press the V control button.
7-42 Infotainment System 2 NOTES
Climate Controls Climate Controls 8-1 Climate Control Systems Dual Automatic Climate Control System Climate Control Systems Dual Automatic Climate Control System . . . . . . . . . . . . . . . . . . . . . . 8-1 The heating, cooling, and ventilation for the vehicle can be controlled with this system. Air Vents Air Vents . . . . . . . . . . . . . . . . . . . . . . 8-3 A. Air Conditioning F. B. Driver and Passenger Temperature Controls G. Recirculation C. Heated Seats I. AUTO (Automatic Mode) D.
8-2 Climate Controls Automatic Operation Manual Operation The system automatically controls the fan speed, air delivery, air conditioning and recirculation in order to heat or cool the vehicle to the desired temperature. Driver and Passenger Temperature Control: The temperature can be adjusted separately for the driver and passenger. When the indicator light is on, the system is in full automatic operation.
Climate Controls automatically to cool the air inside the vehicle or to dry the air needed to defog the windshield faster. h (Recirculation): Press to turn on recirculation. An indicator light comes on. Air is recirculated to quickly cool the inside of the vehicle or prevent outside air and odors from entering. Rear Window Defogger = (Rear Window Defogger): Press to turn the rear window defogger on or off. The rear window defogger turns off automatically after about 10 minutes.
8-4 Climate Controls 2 NOTES
Driving and Operating Driving and Operating Shifting Into Park . . . . . . . . . . . . 9-21 Shifting Out of Park . . . . . . . . . . 9-22 Parking Over Things That Burn . . . . . . . . . . . . . . . . . . 9-22 Engine Exhaust Driving Information Defensive Driving . . . . . . . . . . . . . 9-2 Drunk Driving . . . . . . . . . . . . . . . . . 9-2 Control of a Vehicle . . . . . . . . . . . 9-3 Braking . . . . . . . . . . . . . . . . . . . . . . . 9-3 Steering . . . . . . . . . . . . . . . . . . . . . . .
9-2 Driving and Operating Driving Information Defensive Driving Defensive driving means “always expect the unexpected.” The first step in driving defensively is to wear your safety belt, see Safety Belts on page 3‑8. { WARNING Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready. In addition: . Allow enough following distance between you and the driver in front of you. .
Driving and Operating For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive. Medical research shows that alcohol in a person's system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart.
9-4 Driving and Operating Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is a mistake. The brakes might not have time to cool between hard stops. The brakes will wear out much faster with a lot of heavy braking. Keeping pace with the traffic and allowing realistic following distances eliminates a lot of unnecessary braking. That means better braking and longer brake life.
Driving and Operating Steering Tips Steering in Emergencies It is important to take curves at a reasonable speed. There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. These problems can be avoided by braking — if you can stop in time. But sometimes you cannot stop in time because there is no room.
9-6 Driving and Operating Off-Road Recovery The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. tire contacts the pavement edge. Then turn the steering wheel to go straight down the roadway. Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up.
Driving and Operating While driving on a surface with reduced traction, try to avoid sudden steering, acceleration, or braking, including reducing vehicle speed by shifting to a lower gear. Any sudden changes could cause the tires to slide. You might not realize the surface is slippery until the vehicle is skidding. Learn to recognize warning clues — such as enough water, ice, or packed snow on the road to make a mirrored surface — and slow down when you have any doubt.
9-8 Driving and Operating Other Rainy Weather Tips Highway Hypnosis Hill and Mountain Roads Besides slowing down, other wet weather driving tips include: Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy, find a safe place to park your vehicle and rest. Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: . Allow extra following distance. .
Driving and Operating { WARNING Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down and they could get so hot that they would not work well. You would then have poor braking or even none going down a hill. You could crash. Always have the engine running and the vehicle in gear when going downhill. . Stay in your own lane. Do not swing wide or cut across the center of the road. Drive at speeds that let you stay in your own lane. .
9-10 Driving and Operating Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 13‑5. To get help and keep everyone in the vehicle safe: . Turn on the hazard warning flashers. . Tie a red cloth to an outside mirror. WARNING (Continued) If the vehicle is stuck in the snow: . . Check again from time to time to be sure snow does not collect there. .
Driving and Operating To save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel really uncomfortable from the cold. Moving about to keep warm also helps. If it takes some time for help to arrive, now and then when you run the engine, push the accelerator pedal slightly so the engine runs faster than the idle speed.
9-12 Driving and Operating Vehicle Load Limits It is very important to know how much weight the vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo and all nonfactory‐installed options. Two labels on the vehicle show how much weight it may properly carry, the Tire and Loading Information label and the Certification label.
Driving and Operating number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds. The Tire and Loading Information label also shows the tire size of the original equipment tires (C) and the recommended cold tire inflation pressures (D). For more information on tires and inflation see Tires on page 10‑38 and Tire Pressure on page 10‑46 . There is also important loading information on the Certification label.
9-14 Driving and Operating Example 1 A. Vehicle Capacity Weight for Example 1 = 453 kg (1,000 lbs). Example 2 A. Vehicle Capacity Weight for Example 2 = 453 kg (1,000 lbs). Example 3 A. Vehicle Capacity Weight for Example 3 = 453 kg (1,000 lbs). B. Subtract Occupant Weight B. Subtract Occupant Weight B. Subtract Occupant Weight @ 68 kg (150 lbs) × 2 = 136 kg (300 lbs). @ 68 kg (150 lbs) × 5 = 340 kg (750 lbs). @ 91 kg (200 lbs) × 5 = 453 kg (1,000 lbs). C.
Driving and Operating Refer to the vehicle's Tire and Loading Information label for specific information about the vehicle's capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed the vehicle's capacity weight. Certification Label A vehicle-specific Certification label is attached to the driver side center pillar (B-pillar). The label tells the gross weight capacity of the vehicle, called the Gross Vehicle Weight Rating (GVWR).
9-16 Driving and Operating If you put things inside the vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. { WARNING Things you put inside the vehicle can strike and injure people in a sudden stop or turn, or in a crash. . Put things in the cargo area of the vehicle. In the cargo area, put them as far forward as you can. Try to spread the weight evenly.
Driving and Operating Following break‐in, engine speed and load can be gradually increased. Ignition Positions To shift out of P (Park), turn the ignition to ON/RUN and apply the brake pedal. A (STOPPING THE ENGINE/ LOCK/OFF): When the vehicle is stopped, turn the ignition switch to LOCK/OFF to turn the engine off. Retained Accessory Power (RAP) will remain active. See Retained Accessory Power (RAP) on page 9‑18 for more information. This is the only position from which the key can be removed.
9-18 Driving and Operating B (ACC/ACCESSORY): This position unlocks the steering wheel. Some accessories can used in this position. C (ON/RUN): The ignition switch stays in this position when the engine is running. This position can be used to operate the electrical accessories, as well as to display some warning and indicator lights. The battery could be drained if the key is left in the ON/RUN position with the engine off.
Driving and Operating The vehicle has a Computer-Controlled Cranking System. This feature assists in starting the engine and protects components. If the ignition key is turned to the START position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. If the engine does not start and the key is held in START for many seconds, cranking stops after 15 seconds to prevent cranking motor damage.
9-20 Driving and Operating Engine Heater The engine coolant heater, if available, can help in cold weather conditions at or below −18°C (0°F) for easier starting and better fuel economy during engine warm-up. Plug in the coolant heater at least four hours before starting the vehicle. An internal thermostat in the plug-end of the cord will prevent engine coolant heater operation at temperatures above −18°C (0°F). To Use The Engine Coolant Heater 1. Turn off the engine. 2.
Driving and Operating Shifting Into Park { WARNING It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, use the steps that follow. Use this procedure to shift into P (Park): 1. Hold the brake pedal down and set the parking brake.
9-22 Driving and Operating Shifting Out of Park This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: . . Prevent ignition key removal unless the shift lever is in P (Park) with the shift lever button fully released. Prevent movement of the shift lever out of P (Park), unless the ignition is in ON/RUN or ACC/ ACCESSORY and the brake pedal is applied.
Driving and Operating Engine Exhaust { WARNING Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: . The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes). . The exhaust smells or sounds strange or different. (Continued) WARNING (Continued) . The exhaust system leaks due to corrosion or damage. .
9-24 Driving and Operating Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { WARNING Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation.
Driving and Operating WARNING (Continued) P (Park): This position locks the drive wheels. It is the best position to use when starting the engine because the vehicle cannot move easily. { WARNING It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. (Continued) Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly.
9-26 Driving and Operating R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped. To rock the vehicle back and forth to get out of snow, ice or sand without damaging the transmission, see If the Vehicle is Stuck on page 9‑11. N (Neutral): In this position, the engine does not connect with the wheels.
Driving and Operating Manual Mode Driver Shift Control (DSC) Notice: If you drive the vehicle at high RPMs without upshifting while using Driver Shift Control (DSC), you could damage the vehicle. Always upshift when necessary while using DSC. 9-27 Driver Shift Control (DSC) allows you to shift an automatic transmission similar to a manual transmission.
9-28 Driving and Operating Brakes Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little. This is normal. If there is a problem with ABS, this warning light stays on.
Driving and Operating Parking Brake Driver Information Center (DIC) messages. See Brake System Messages on page 5‑24 for more information. In case of insufficient electrical power, the EPB cannot be applied or released. Before leaving the vehicle, check the park brake status lamp to ensure that the park brake is applied. EPB Apply The vehicle has an Electric Parking Brake (EPB). The switch for the EPB is on the center console. The EPB can always be activated, even if the ignition is OFF.
9-30 Driving and Operating If the park brake warning light is on, the EPB has detected an error in another system and is operating with reduced functionality. To apply the EPB when this light is on, lift up on the EPB switch and hold it in the up position. Full application of the parking brake by the EPB system may take a longer period of time than normal when this light is on. Continue to hold the switch until the park brake status light remains on. If the park brake warning light is on, see your dealer.
Driving and Operating Brake Assist Hill Start Assist (HSA) This vehicle has a brake assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability system hydraulic brake control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the vehicle.
9-32 Driving and Operating d flashes to indicate that the traction control system is active. See Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light on page 5‑17 for more information. Notice: Do not repeatedly brake or accelerate heavily when TCS is off. The vehicle's driveline could be damaged. 1. Stopping the vehicle. 2. Turning the engine off and waiting 15 seconds. 3. Starting the engine. If d still comes on and stays on, the vehicle needs service.
Driving and Operating Electronic Stability Control (ESC) The vehicle may have a vehicle stability enhancement system called StabiliTrak®. It is an advanced computer-controlled system that assists with directional control of the vehicle in difficult driving conditions. StabiliTrak activates when there is a difference between the intended path and the direction the vehicle is actually traveling.
9-34 Driving and Operating When StabiliTrak is turned off, the system will not assist with directional control of the vehicle or limit wheel spin. Driving should be adjusted accordingly. See Electronic Stability Control (ESC) Off Light on page 5‑17 for more information. . . To turn off both StabiliTrak and TCS, press and hold d, located on the instrument panel, until g illuminates and the appropriate DIC message is displayed. See Ride Control System Messages on page 5‑27.
Driving and Operating TOUR: Use for long-distance highway driving. This setting provides a smooth, soft ride. Press and release the TOUR button and the light on the button comes on. This mode provides a comfortable, smooth ride. Press the button again and the system returns to the Standard mode. IDCS automatically comes on in the Standard mode when the vehicle is started. When the Sport and Tour modes are turned off, the system returns to the Standard mode. .
9-36 Driving and Operating If Standard mode is selected and sport driving is detected, several settings of the Standard mode change to sport settings. If sport driving increases, DMC changes to SPORT mode. If TOUR mode is selected and sudden braking or cornering is necessary, DMC changes the suspension settings to SPORT mode to increase vehicle stability.
Driving and Operating 5 (On/Off): Press to turn the cruise control system on and off. An indicator light will turn on or off in the instrument panel cluster. [ (Cancel): Press to disengage cruise control without erasing the set speed from memory. RES/+ (Resume/Accelerate): Move the thumbwheel up to make the vehicle resume to a previously set speed or to accelerate. SET/− (Set/Coast): Move the thumbwheel down to set a speed or to make the vehicle decelerate.
9-38 Driving and Operating Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the previous set cruise control speed. Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed.
Driving and Operating { WARNING The Ultrasonic Rear Parking Assist (URPA) system does not replace driver vision. It cannot detect: . . Objects that are below the bumper, underneath the vehicle, or too close or far from the vehicle Children, pedestrians, bicyclists, or pets. If you do not use proper care before and while backing, vehicle damage, injury, or death could occur. Even with URPA, always check behind the vehicle before backing up.
9-40 Driving and Operating When the System Does Not Seem to Work Properly . SERVICE PARK ASSIST: If this message occurs, take the vehicle to your dealer to repair the system. PARK ASSIST OFF: If the URPA system does not activate due to a temporary condition, the message displays on the DIC. See Driver Information Center (DIC) on page 5‑21 for more information. This can occur under the following conditions: . The driver has disabled the system. . The ultrasonic sensors are not clean.
Driving and Operating The VIN is at the top left of the instrument panel. See Vehicle Identification Number (VIN) on page 12‑1. Vehicles that have a FlexFuel badge and a yellow fuel cap can use either unleaded gasoline or ethanol fuel containing up to 85% ethanol (E85). See Fuel E85 (85% Ethanol) on page 9‑43. For all other vehicles, use only the unleaded gasoline described under Recommended Fuel on page 9‑41.
9-42 Driving and Operating Gasoline Specifications At a minimum, gasoline should meet ASTM specification D 4814 in the United States or CAN/ CGSB‐3.5 or 3.511 in Canada. Some gasolines contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). We recommend against the use of gasolines containing MMT. See Fuel Additives on page 9‑42 for additional information.
Driving and Operating For customers who do not use TOP TIER Detergent Gasoline regularly, one bottle of GM Fuel System Treatment PLUS, added to the fuel tank at every engine oil change, can help clean deposits from fuel injectors and intake valves. GM Fuel System Treatment PLUS is the only gasoline additive recommended by General Motors. It is available at your dealer. Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area.
9-44 Driving and Operating At a minimum, E85 should meet ASTM Specification D 5798 or CGSB Specification 3.512. Filling the tank with fuel mixtures that do not meet ASTM or CGSB specifications can affect driveability and could cause the malfunction indicator lamp to come on. As the outside temperature approaches freezing, ethanol fuel distributors should supply winter grade ethanol, the same as with unleaded gasoline.
Driving and Operating The tethered fuel cap is behind the fuel door on the vehicle's passenger side. The fuel door is unlocked when the vehicle is unlocked. Locking the vehicle locks the fuel door. Turn the fuel cap counterclockwise to remove. While refueling, hang the tethered fuel cap from the disk on the end of the fuel cap to the mating feature on the fuel door hinge. Reinstall the cap by turning it clockwise until it clicks.
9-46 Driving and Operating Filling a Portable Fuel Container { WARNING Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others: . Dispense fuel only into approved containers. . Do not fill a container while it is inside a vehicle, in a vehicle's trunk, pickup bed, or on any surface other than the ground.
Driving and Operating Conversions and Add-Ons Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle's warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain the vehicle 12‐volt battery, even if the vehicle is not operating. The vehicle has an airbag system.
9-48 Driving and Operating 2 NOTES
Vehicle Care Vehicle Care General Information General Information . . . . . . . . . . California Proposition 65 Warning . . . . . . . . . . . . . . . . . . . . California Perchlorate Materials Requirements . . . . Accessories and Modifications . . . . . . . . . . . . . . . 10-2 10-3 10-3 10-3 Vehicle Checks Doing Your Own Service Work . . . . . . . . . . . . . . . 10-4 Hood . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Engine Compartment Overview . . . . . . . . . . . . . . . . . . .
10-2 Vehicle Care Wheels and Tires Tires . . . . . . . . . . . . . . . . . . . . . . . . 10-38 Winter Tires . . . . . . . . . . . . . . . . 10-39 Tire Sidewall Labeling . . . . . . 10-40 Tire Designations . . . . . . . . . . . 10-42 Tire Terminology and Definitions . . . . . . . . . . . . . . . . 10-43 Tire Pressure . . . . . . . . . . . . . . . 10-46 Tire Pressure for High-Speed Operation . . . . . . . . . . . . . . . . . 10-47 Tire Pressure Monitor System . . . . . . . . . . . . . . . . . . .
Vehicle Care 10-3 California Proposition 65 Warning California Perchlorate Materials Requirements Accessories and Modifications Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
10-4 Vehicle Care GM Accessories are designed to complement and function with other systems on the vehicle. Your GM dealer can accessorize the vehicle using genuine GM Accessories. When you go to your GM dealer and ask for GM Accessories, you will know that GM-trained and supported service technicians will perform the work using genuine GM Accessories. Also, see Adding Equipment to the Airbag-Equipped Vehicle on page 3‑34.
Vehicle Care 10-5 Hood To close the hood: To open the hood: 1. Before closing the hood, be sure all the filler caps are on properly. 2. Lower the hood 30 cm (12 in) above the vehicle and release it so it fully latches. Check to make sure the hood is closed and repeat the process if necessary. 1. Pull up on the hood release handle with this symbol on it. It is located inside the vehicle to the left of the steering column. 2.
10-6 Vehicle Care Engine Compartment Overview 2.
Vehicle Care A. Engine Air Cleaner/Filter on page 10‑13. B. Engine Cover. C. Engine Oil Dipstick. See Engine Oil on page 10‑9. D. Engine Oil Fill Cap. See Engine Oil on page 10‑9. E. Transmission Fluid Cap and Dipstick. See Automatic Transmission Fluid on page 10‑13. F. Power Steering Reservoir and Cap. See Power Steering Fluid on page 10‑21. G. Brake Master Cylinder Reservoir. See Brakes on page 10‑23. 10-7 H. Battery Cover. See Battery on page 10‑25. I. Engine Coolant Reservoir and Pressure Cap.
10-8 Vehicle Care 2.
Vehicle Care A. Engine Air Cleaner/Filter on page 10‑13. B. Engine Cover. C. Engine Oil Fill Cap. See Engine Oil on page 10‑9. D. Engine Oil Dipstick. See Engine Oil on page 10‑9. E. Transmission Fluid Cap and Dipstick. See Automatic Transmission Fluid on page 10‑13. F. Brake Master Cylinder Reservoir. See Brakes on page 10‑23. G. Power Steering Reservoir and Cap. See Power Steering Fluid on page 10‑21. H. Engine Coolant Reservoir and Pressure Cap. See Engine Coolant on page 10‑16. I. Battery Cover.
10-10 Vehicle Care or thickness. Do not use other viscosity oils such as SAE 20W-50. . American Petroleum Institute (API) starburst symbol See Engine Compartment Overview on page 10‑6 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through. What Kind of Engine Oil to Use (2.4L Engine) Look for three things: . GM6094M Use only an oil that meets GM Standard GM6094M. .
Vehicle Care What Kind of Engine Oil to Use (2.0L Engine) 10-11 SAE 0W-30 oil should be used. An oil of this viscosity grade will provide easier cold starting for the engine at extremely low temperatures. When selecting an oil of the appropriate viscosity grade, be sure to always select an oil that meets the required specification. . Specification The vehicle's engine requires a special oil meeting the dexos™ specification.
10-12 Vehicle Care engine oils that meet the requirements of the dexos™ specification. Engine Oil Life System Substitute Engine Oil: When adding oil to maintain engine oil level, oil meeting the dexos™ specification might not be available. You can add substitute oil designated SAE 5W-30 with the API starburst symbol at all temperatures. Substitute oil not meeting the dexos™ specification or equivalent, however, should not be used for an oil change.
Vehicle Care 3. Press the set button to clear the CHANGE ENGINE OIL SOON message and/or restore the REMAINING OIL LIFE 100% message. 4. Turn the ignition to LOCK/OFF. from the filter before disposal. Never dispose of oil by putting it in the trash or pouring it on the ground, into sewers, or into streams or bodies of water. Recycle it by taking it to a place that collects used oil. 10-13 The procedure can be found in the service manual.
10-14 Vehicle Care If you are driving in dusty/dirty conditions, inspect the filter at each engine oil change. 7. Inspect or replace the engine air cleaner/filter. 8. Reverse Steps 2 through 4 to reinstall the filter cover housing. How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt. If the filter remains caked with dirt, a new filter is required.
Vehicle Care 3. Disconnect the electrical connector (C). 4. Remove the screws (A) on top of the engine air cleaner/filter housing. 5. Lift the filter cover housing away from the engine. 6. Pull out the filter. 7. Inspect or replace the engine air cleaner/filter. 8. Reverse Steps 2 through 4 to reinstall the filter cover housing. { WARNING Operating the engine with the air cleaner/filter off can cause you or others to be burned.
10-16 Vehicle Care 2.4 L L4 Engine { WARNING Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle. A. Electric Engine Cooling Fans B.
Vehicle Care What to Use { WARNING Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned.
10-18 Vehicle Care How to Add Coolant to the Coolant Surge Tank Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged. If no problem is found, check to see if coolant is visible in the coolant surge tank.
Vehicle Care By this time, the coolant level inside the coolant surge tank may be lower. If the level is lower, add more of the proper DEX-COOL® coolant mixture to the coolant surge tank until the level reaches the indicated level mark. 2.0 L L4 Engine Shown, 2.4 L L4 Engine Similar 1. Remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot.
10-20 Vehicle Care Engine Overheating The vehicle has several indicators to warn of engine overheating. You will find an engine coolant temperature gauge on the vehicle's instrument panel cluster. See Engine Coolant Temperature Gauge on page 5‑9. If it is decided not to lift the hood when this warning appears, but instead get service help right away, see Roadside Assistance Program on page 13‑5. If it is decided to lift the hood , make sure the vehicle is parked on a level surface.
Vehicle Care If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you. If the warning does not come back on, continue to drive normally. If the warning continues, pull over, stop, and park the vehicle right away. If there is no sign of steam, idle the engine for three minutes while parked.
10-22 Vehicle Care 4. Replace the cap and completely tighten it. 5. Remove the cap again and look at the fluid level on the dipstick. The fluid level should be between the MIN (Minimum) and MAX (Maximum) marks when the engine is cold, and at the MAX mark when the engine is hot. If the fluid is at the MIN mark when the engine is cold or hot, power steering fluid should be added. Washer Fluid What to Use When windshield washer fluid is needed, be sure to read the manufacturer's instructions before use.
Vehicle Care Brakes This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly. { WARNING The brake wear warning sound means that soon the brakes will not work well. That could lead to a crash. When the brake wear warning sound is heard, have the vehicle serviced.
10-24 Vehicle Care Brake Fluid The brake master cylinder reservoir is filled with DOT 4 brake fluid as indicated on the reservoir cap. See Engine Compartment Overview on page 10‑6 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: . . The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up.
Vehicle Care Notice: . . Using the wrong fluid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid. If brake fluid is spilled on the vehicle's painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle.
10-26 Vehicle Care 3. For automatic transmission vehicles, try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service. For manual transmission vehicles, put the shift lever in Neutral, push the clutch pedal down halfway, and try to start the engine. The vehicle should start only when the clutch pedal is pushed down all the way to the floor.
Vehicle Care Park Brake and P (Park) Mechanism Check { WARNING When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move. Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. .
10-28 Vehicle Care 3. With the latch open, pull the wiper blade down towards the windshield far enough to release it from the J-hooked end of the wiper arm. Headlamp Aiming Bulb Replacement Headlamp aim has been preset at the factory and should need no further adjustment. For the proper type of replacement bulbs, see Replacement Bulbs on page 10‑32. 4. However, if the vehicle is damaged in a crash, the headlamp aim may be affected.
Vehicle Care Headlamps, Front Turn Signal and Parking Lamps 10-29 2. Remove the outside cap for the low-beam headlamp/DRL bulb replacement from the back of the headlamp assembly. 3. Remove the inside cap for the high-beam headlamp bulb replacement from the back of the headlamp assembly. 4. Disconnect the electrical connector. Up–Level Headlamp Assembly (Passenger Side Shown, Driver Side Similar) Base Headlamp Assembly (Passenger Side Shown, Driver Side Similar) A. High‐Beam Headlamp B.
10-30 Vehicle Care Front Turn Signal/Parking/Side Marker Lamps (Base and Up-Level) To replace the front turn signal, parking lamp, or side marker lamp: 1. For the driver side bulb, remove the windshield washer bottle filler neck by firmly pulling it straight up and out of the bottle. 6. For the driver side, reinstall the windshield washer bottle filler neck by firmly pushing it straight into the bottle. Ensure that the filler neck clip engages into the underhood electrical center retainer.
Vehicle Care 3. Remove the two nuts that secure the taillamp assembly. 8. Turn the bulb socket clockwise to install it. 4. Remove the taillamp assembly and detach the wiring harness connector. 9. Reverse Steps 2 through 4 to reinstall the taillamp assembly. 10-31 License Plate Lamp To replace one of these bulbs: A. Bulb Socket B. Bulb C. Lamp Assembly 3. Turn the bulb socket (A) counterclockwise to remove it from the lamp assembly (C). A. Back-up Lamp B. Taillamp C. Stop/Turn Signal Lamp D.
10-32 Vehicle Care 5. Push the replacement bulb straight into the bulb socket and turn the bulb socket clockwise to install it into the lamp assembly. 6. Push the lamp assembly back into position until the release tab locks into place.
Vehicle Care Fuses and circuit breakers protect the following in the vehicle: . Headlamp Wiring . Windshield Wiper Motor . Power Windows and other Power Accessories Replace a bad fuse with a new one of the identical size and rating. If there is a problem on the road and a fuse needs to be replaced, the same amperage fuse can be borrowed. Choose some feature of the vehicle that is not needed to use and replace it as soon as possible.
10-34 Vehicle Care Engine Compartment Fuse Block Fuse Number To remove the fuse block cover, press the three retaining clips on the cover and lift it straight up. Notice: Spilling liquid on any electrical components on the vehicle may damage it. Always keep the covers on any electrical component.
Vehicle Care Fuse Number Usage Fuse Number Usage 12 Starter 25 Power Outlets 13 Fuel System Control Module 26 Antilock Brake System Pump 14 Secondary Air Induction 27 15 Not Used 16 Vacuum Pump 17 Ignition, Airbag 18 Not Used 19 Not Used 20 Not Used 21 Rear Power Windows 22 Antilock Brake System Valve 23 Variable Effort Steering 24 Front Power Windows Fuse Number 10-35 Usage 37 Right Hand High‐Beam Headlamp Electric Parking Brake 38 Left Hand High‐Beam Headlamp 28
10-36 Vehicle Care Fuse Number 49 Usage Right Hand Low Beam, High Intensity Discharge Headlamp 50 Left Hand Low Beam, High Intensity Discharge Headlamp 51 Horn 52 53 54 55 56 57 58 Motor Indicator Lamp Ignition, Inside Rear View Mirror Fuse Number 59 Windshield Washer Not Used Not Used Secondary Air Induction 60 Heated Mirrors 61 Not Used 62 Canister Vent Solenoid 63 Not Used 64 Not Used 65 Not Used 66 Not Used 67 Fuel System Control Module 68 Not Used 69 Battery Sensor 70
Vehicle Care Relay Number Usage K15 Ignition K16 Secondary AIR Pump K17 Window/Mirror Defog To access the fuses, open the storage compartment. Press in on the sides of the compartment to release it from the instrument panel. Pull the door toward you to release it from the hinge. Instrument Panel Fuse Block Number The instrument panel fuse block is located in the instrument panel, on the driver side of the vehicle.
10-38 Vehicle Care Number Usage Number Usage 13 Left Hand Power Front Seat 20 Automatic Occupant Sensing 14 Diagnostic Link Connector 21 Instrument Panel Cluster 15 Airbag 22 16 Trunk Release Discrete Logic Ignition Switch Heater Ventilation Air Conditioning Controller 23 17 Body Control Module 1 24 Body Control Module 2 18 Service Fuse, Logistic Relay 25 OnStar® 19 Not Used 26 Power Outlet, Trunk Wheels and Tires Tires Your new vehicle comes with high-quality tires made by
Vehicle Care WARNING (Continued) . . Under inflated tires pose the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold. Over inflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when you hit a pothole. Keep tires at the recommended pressure. . Worn or old tires can cause a crash.
10-40 Vehicle Care criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. If you choose to use winter tires: . Use tires of the same brand and tread type on all four wheel positions. . Use only radial ply tires of the same size, load range, and speed rating as the original equipment tires. Winter tires with the same speed rating as your original equipment tires may not be available for H, V, W, Y, and ZR speed rated tires.
Vehicle Care compact spare tire, see Compact Spare Tire on page 10‑67 and If a Tire Goes Flat on page 10‑60 . (E) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 10‑56 .
10-42 Vehicle Care (E) Tire Inflation: The temporary use tire or compact spare tire should be inflated to 420 kPa (60 psi). For more information on tire pressure and inflation see Tire Pressure on page 10‑46 . (F) Tire Size : A combination of letters and numbers define a tire's width, height, aspect ratio, construction type, and service description. The letter T as the first character in the tire size means the tire is for temporary use only.
Vehicle Care (F) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load. Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in psi (pounds per square inch) or kPa (kilopascal).
10-44 Vehicle Care GVWR: Gross Vehicle Weight Rating. See Vehicle Load Limits on page 9‑12. GAWR FRT: Gross Axle Weight Rating for the front axle. See Vehicle Load Limits on page 9‑12. GAWR RR: Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits on page 9‑12. Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure.
Vehicle Care Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure on page 10‑46 and Vehicle Load Limits on page 9‑12. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead.
10-46 Vehicle Care Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under‐inflation or over‐inflation is all right. It is not. If your tires do not have enough air (under‐inflation), you can get the following: . Tire overloading and over-heating which could lead to a blowout. . Premature or irregular wear. . Poor handling. . Reduced fuel economy.
Vehicle Care your vehicle has been sitting for at least three hours or driven no more than 1.6 km (1 mile). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until you reach the recommended amount.
10-48 Vehicle Care Tire Pressure Monitor System pressure telltale when one or more of your tires is significantly under‐inflated. The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle.
Vehicle Care 10-49 Federal Communications Commission (FCC) and Industry Canada DIC operation and displays, see Driver Information Center (DIC) on page 5‑21. See Radio Frequency Statement on page 13‑15 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310. The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as you start to drive.
10-50 Vehicle Care Your vehicle's TPMS can warn you about a low tire pressure condition, but it does not replace normal tire maintenance. See Tire Inspection on page 10‑52, Tire Rotation on page 10‑52, and Tires on page 10‑38. Notice: Tire sealant materials are not all the same. A non-approved tire sealant could damage the Tire Pressure Monitor System (TPMS) sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty.
Vehicle Care . Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction. If the TPMS is not functioning it cannot detect or signal a low tire condition. See your dealer for service if the TPMS malfunction light and DIC message come on and stay on. TPMS Sensor Matching Process Each TPMS sensor has a unique identification code.
10-52 Vehicle Care for five seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, confirms that the sensor identification code has been matched to this tire and wheel position. 9. Proceed to the passenger side front tire, and repeat the procedure in Step 8. 10. Proceed to the passenger side rear tire, and repeat the procedure in Step 8. 11. Proceed to the driver side rear tire, and repeat the procedure in Step 8.
Vehicle Care Any time you notice unusual wear, rotate the tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 10‑53 and Wheel Replacement on page 10‑58. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. See Tire Pressure on page 10‑46 and Vehicle Load Limits on page 9‑12. Reset the Tire Pressure Monitor System.
10-54 Vehicle Care typically need to be replaced due to wear before they may need to be replaced due to age. Consult the tire manufacturer for more information on when tires should be replaced. Vehicle Storage One way to tell when it is time for new tires is to check the treadwear indicators, which appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. See Tire Inspection on page 10‑52 and Tire Rotation on page 10‑52 for additional information. The rubber in tires ages over time.
Vehicle Care traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all‐season tread design, the TPC Spec number will be followed by an MS for mud and snow. See Tire Sidewall Labeling on page 10‑40 for additional information. GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new.
10-56 Vehicle Care size, load range, speed rating, and construction type (radial and bias‐belted tires) as your vehicle's original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low‐pressure warning if non‐TPC Spec rated tires are installed on your vehicle. Non‐TPC Spec rated tires may give a low‐pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires. See Tire Pressure Monitor System on page 10‑48.
Vehicle Care Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires.
10-58 Vehicle Care conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
Vehicle Care WARNING (Continued) dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.
10-60 Vehicle Care If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle's tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly.
Vehicle Care { WARNING Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1. Set the parking brake firmly. WARNING (Continued) the one being changed. That would be the tire on the other side, at the opposite end of the vehicle.
10-62 Vehicle Care Removing the Flat Tire and Installing the Spare Tire 3. Turn the retainer nut counterclockwise and remove the spare tire. Place the spare tire next to the tire being changed. 4. The jack and tools are stored below the spare tire. Remove them from their container and place them near the tire being changed. Take off the wheel cover or center cap, if the vehicle has one, to reach the wheel bolts. 1. Do a safety check before proceeding.
Vehicle Care Notice: Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty. { WARNING Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle. Place the jack notch, as shown. 7. Put the compact spare tire near you. { WARNING 6.
10-64 Vehicle Care 8. Attach the jack handle extension onto the jack by sliding the hook through the end of the jack. WARNING (Continued) paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See If a Tire Goes Flat on page 10‑60. 9. Place the jack under the vehicle. 11. Remove all of the wheel nuts. 12. Remove the flat tire. { WARNING 10. Raise the vehicle by turning the jack handle clockwise.
Vehicle Care { WARNING Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash. 15. Reinstall the wheel nuts. Tighten each nut by hand until the wheel is held against the hub. 16. Lower the vehicle by turning the jack handle counterclockwise. { WARNING Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off.
10-66 Vehicle Care When reinstalling the wheel cover or center cap on the full-size tire, tighten all five plastic caps hand snug with the aid of the wheel wrench and tighten them with the wheel wrench an additional one‐quarter of a turn. Notice: Wheel covers will not fit on your vehicle's compact spare. If you try to put a wheel cover on the compact spare, the cover or the spare could be damaged.
Vehicle Care To store the compact spare tire, use the shorter mounting bolt. The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can. Compact Spare Tire { WARNING Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.
10-68 Vehicle Care Jump Starting If the battery has run down, try to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { WARNING Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. The jump start negative (A) is the power steering line fitting and bolt on the top of the power steering pump. Batteries can hurt you. They can be dangerous because: . They contain acid that can burn you. .
Vehicle Care 2. Position the two vehicles so that they are not touching. { WARNING 3. Set the parking brake firmly and put the shift lever in P (Park). See Shifting Into Park on page 9‑21. An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty.
10-70 Vehicle Care 7. Connect one end of the black negative (–) cable to the negative (–) terminal of the good battery (C). Use a remote negative (−) terminal if the vehicle has one. 5. Connect one end of the red positive (+) cable to the jump start positive (+) post (A). Use a remote positive (+) terminal if the vehicle has one. 6. Do not let the other end of the red positive (+) cable touch metal. Connect it to the positive (+) terminal of the good battery (B).
Vehicle Care To disconnect the jumper cables from both vehicles: Towing 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. Towing the Vehicle 2. Disconnect the black negative (−) cable from the vehicle with the good battery. Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part or Remote Negative (–) Terminal B. Good Battery or Remote Positive (+) and Remote Negative (–) Terminals C. Dead Battery or Remote Positive (+) Terminal 3.
10-72 Vehicle Care Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle, such as behind a motorhome. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground. Dolly towing is towing the vehicle with two wheels on the ground and two wheels up on a device known as a dolly.
Vehicle Care 5. Release the parking brake only after the vehicle being towed is firmly attached to the towing vehicle. Dolly Towing From the Front 3. Shift the transmission to P (Park). 4. Firmly set the parking brake. 5. Use an adequate clamping device designed for towing to ensure that the front wheels are locked into the straight-ahead position. When towing the vehicle for extended periods of time, start the vehicle as often as possible to prevent battery drain.
10-74 Vehicle Care Dolly Towing From the Rear Appearance Care Exterior Care Cleaning Exterior Lamps/ Lenses Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing the Vehicle” later in this section. Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer.
Vehicle Care Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Wash with water or use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam, or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts.
10-76 Vehicle Care Wheels and Trim — Aluminum or Chrome The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft, clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft, clean towel. A wax may then be applied. Notice: Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium or sodium chloride.
Vehicle Care Wipers can be damaged by: . Extreme dusty conditions . Sand and salt Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty. . Heat and sun Finish Damage . Snow and ice, without proper removal Any stone chips, fractures, or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Tires Use a stiff brush with tire cleaner to clean the tires.
10-78 Vehicle Care plastic surfaces. Stains should be removed quickly as extreme heat could cause them to set rapidly. Lighter colored interiors may require more frequent cleaning. Newspapers and garments that can transfer color to home furnishings can also transfer color to the vehicle's interior. Remove dust from small buttons and knobs with a small brush with soft bristles. Your dealer has products for cleaning the vehicle's interior.
Vehicle Care only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda. Before cleaning, gently remove as much of the soil as possible using one of the following techniques: . For liquids: gently blot the remaining soil with a paper towel. Allow the soil to absorb into the paper towel until no more can be removed. . For solid dry soils: remove as much as possible and then vacuum. To clean: 1.
10-80 Vehicle Care use silicone or wax-based products, or those containing organic solvents to clean the vehicle's interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Floor Mats Some commercial products may increase gloss on the instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. . Use the floor mat with the correct side up.
Service and Maintenance Service and Maintenance General Information General Information . . . . . . . . . . 11-1 Scheduled Maintenance Scheduled Maintenance . . . . . 11-2 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . . 11-6 Maintenance Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 11-8 Maintenance Records Maintenance Records . . . . . . . .
11-2 Service and Maintenance { WARNING Performing maintenance work can be dangerous. Some jobs can cause serious injury. Perform maintenance work only if you have the required know-how and the proper tools and equipment. If in doubt, see your dealer to have a qualified technician do the work. See Doing Your Own Service Work on page 10‑4. At your dealer, you can be certain that you will receive the highest level of service available.
Service and Maintenance system whenever the oil is changed. See Engine Oil Life System on page 10‑12. Every Engine Oil Change . Change engine oil and filter. Reset oil life system. See Engine Oil on page 10‑9 and Engine Oil Life System on page 10‑12. An Emission Control Service. . Engine coolant level check. See Engine Coolant on page 10‑16. . Engine cooling system inspection. Visual inspection of hoses, pipes, fittings, and clamps and replacement, if needed. . .
11-4 Service and Maintenance Additional Required Services Once a Year Every 12 000 km/7,500 Miles . . Rotate tires. Tires should be rotated every 12 000 km/ 7,500 miles. See Tire Rotation on page 10‑52. At Each Fuel Stop . Engine oil level check. See Engine Oil on page 10‑9. . Engine coolant level check. See Engine Coolant on page 10‑16. . Windshield washer fluid level check. See Washer Fluid on page 10‑22. Once a Month . Tire inflation check. See Tire Pressure on page 10‑46. .
Service and Maintenance First Engine Oil Change After Every 80 000 km/50,000 Miles . Engine air cleaner filter replacement. See Engine Air Cleaner/Filter on page 10‑13. . Automatic transmission fluid change (severe service) for vehicles mainly driven in heavy city traffic in hot weather, in hilly or mountainous terrain, or used for taxi, police, or delivery service. See Automatic Transmission Fluid on page 10‑13. . Evaporative control system inspection.
11-6 Service and Maintenance Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants Usage Fluid/Lubricant Engine Oil (2.4L Engine) Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. To determine the proper viscosity for the vehicle's engine, see Engine Oil on page 10‑9. Engine Oil (2.0L Engine) The engine requires a special oil meeting the dexos™ specification.
Service and Maintenance Usage Hood Latch Assembly, Secondary Latch, Pivots, Spring Anchor, and Release Pawl Hood and Door Hinges Weatherstrip Conditioning 11-7 Fluid/Lubricant Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Weatherstrip Lubricant (GM Part No. U.S.
11-8 Service and Maintenance Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your retailer. Part GM Part Number ACDelco Part Number 55560894 A3128C 2.0L L4 Engine 12605565 PF458G 2.4L L4 Engine 12605566 PF457G 13271191 CF176 2.0L L4 Engine 12620540 41–108 2.4L L4 Engine 12620540 41–108 Driver Side – 60.0 cm (23.62 in) 13227404 — Passenger Side – 45.0 cm (17.
Service and Maintenance 11-9 Maintenance Records After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts.
11-10 Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed
Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 11-11
11-12 Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed
Technical Data Technical Data Vehicle Identification Vehicle Identification Vehicle Identification Number (VIN) Vehicle Identification Number (VIN) . . . . . . . . . . . . . . 12-1 Service Parts Identification Label . . . . . . . . . . . . . . . . . . . . . . . 12-1 Vehicle Data Capacities and Specifications . . . . . . . . . . . . . . 12-2 Engine Drive Belt Routing . . . 12-4 This legal identifier is in the front corner of the instrument panel, on the left side of the vehicle.
12-2 Technical Data Vehicle Data Capacities and Specifications Application Air Conditioning Refrigerant R134a Capacities Metric English For the air conditioning system refrigerant charge amount, see the refrigerant label located under the hood. See your dealer for more information. Engine Cooling System 2.0L L4 Engine 7.8 L 8.2 qt 2.4L L4 Engine 7.1 L 7.5 qt 2.0L L4 Engine 5.7 L 6.0 qt 2.4L L4 Engine 4.7 L 5.0 qt 2.0L, 2.4L L4 Engine (with NU5 and NT7 emissions) 73.9 L 19.5 gal 2.
Technical Data Capacities Application Metric English — — 8.4 L 8.9 qt 150 Y 110 lb ft Transmission Fluid* (Drain and Refill) 2.0L L4 Engine, 6–Speed Automatic (Transmission Requires No Fluid Replacement) 2.4L L4 Engine, 6–Speed Automatic Wheel Nut Torque *See Automatic Transmission Fluid on page 10‑13 for information on checking fluid level. All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual. Recheck fluid level after filling.
12-4 Technical Data Engine Drive Belt Routing
Customer Information Customer Information Customer Information Customer Satisfaction Procedure . . . . . . . . . . . . . . . . . . 13-1 Customer Assistance Offices . . . . . . . . . . . . . . . . . . . . . 13-3 Customer Assistance for Text Telephone (TTY) Users . . . . . 13-4 Online Owner Center . . . . . . . . 13-4 GM Mobility Reimbursement Program . . . . . . . . . . . . . . . . . . . . 13-5 Roadside Assistance Program . . . . . . . . . . . . . . . . . . . . 13-5 Scheduling Service Appointments . . . . .
13-2 Customer Information STEP TWO: If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, in the U.S., call 1-800-521-7300, Customer Assistance prompt. In Canada, contact General Motors of Canada Customer Communication Centre at 1‐800-263-3777 (English) or 1-800-263-7854 (French). We encourage you to call the toll-free number in order to give your inquiry prompt attention.
Customer Information STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps One and Two, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration program. General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory-related vehicle service claims.
13-4 Customer Information Canada General Motors of Canada Limited Customer Communication Centre, Mail Code: CA1-163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 www.gm.ca 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800 All Overseas Locations Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S.
Customer Information or schedule a service appointment by adding the vehicles you own to your driveway profile. Help Center — www.buick.com/ helpcenter . FAQ . Contact Us My GM Canada (Canada) — www.gm.ca My GM Canada is a password-protected section of www.gm.ca where you can save information on GM vehicles, get personalized offers, and use handy tools and forms with greater ease. . My Preferences: Manage your profile and use tools and forms with greater ease.
13-6 Customer Information Calling for Assistance When calling Roadside Assistance, have the following information ready: . Your name, home address, and home telephone number . Telephone number of your location . Location of the vehicle . Model, year, color, and license plate number of the vehicle . Odometer reading, Vehicle Identification Number (VIN), and delivery date of the vehicle . Description of the problem Roadside Assistance is not a part of the New Vehicle Limited Warranty.
Customer Information . Towing or services for vehicles driven on a non-public road or highway. General Motors of Canada Limited requires pre-authorization, original detailed receipts, and a copy of the repair orders. Once authorization has been received, the Roadside Assistance advisor will help you make arrangements and explain how to receive payment. Services Specific to Canadian‐Purchased Vehicles . Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted.
13-8 Customer Information Courtesy Transportation Program To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the Bumper to Bumper (Base Warranty Coverage period in Canada), extended powertrain, and/or hybrid‐specific warranties in both the U.S. and Canada. Several Courtesy Transportation options are available to assist in reducing your inconvenience when warranty repairs are required.
Customer Information Requirements vary and may include minimum age requirements, insurance coverage, credit card, etc. You are responsible for fuel usage charges and may also be responsible for taxes, levies, usage fees, excessive mileage, or rental usage beyond the completion of the repair. It may not be possible to provide a like vehicle as a courtesy rental. Additional Program Information All program options, such as shuttle service, may not be available at every dealer.
13-10 Customer Information subsequent collisions. Aftermarket parts are not covered by your GM New Vehicle Limited Warranty, and any vehicle failure related to such parts is not covered by that warranty. Repair Facility GM also recommends that you choose a collision repair facility that meets your needs before you ever need collision repairs.
Customer Information . Vehicle Identification Number (VIN) . Insurance company and policy number . General description of the damage to the other vehicle Choose a reputable repair facility that uses quality replacement parts. See “Collision Parts” earlier in this section. If the airbag has inflated, see What Will You See After an Airbag Inflates? on page 3‑28.
13-12 Customer Information In-Portfolio: Includes a Portfolio, Owner Manual, and Warranty Booklet. ORDER TOLL FREE: 1-800-551-4123 Monday - Friday 8:00 AM - 6:00 PM Eastern Time RETAIL SELL PRICE: $35.00 (U.S.) plus handling and shipping fees For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc. on the World Wide Web at: www.helminc.com Without Portfolio: Owner Manual only. Or you can write to: RETAIL SELL PRICE: $25.00 (U.S.) plus handling and shipping fees Helm, Incorporated P.
Customer Information However, NHTSA cannot become involved in individual problems between you, your dealer, or General Motors. Reporting Safety Defects to the Canadian Government To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: If you live in Canada, and you believe that your vehicle has a safety defect, notify Transport Canada immediately, and notify General Motors of Canada Limited.
13-14 Customer Information Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment, to deploy airbags in a crash, and to provide antilock braking to help the driver control the vehicle.
Customer Information GM will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an official request by police or similar government office; as part of GM's defense of litigation through the discovery process; or, as required by law.
13-16 Customer Information 2 NOTES
INDEX A Accessories and Modifications . . . . . . . . . . . . . . . . . 10-3 Accessory Power . . . . . . . . . . . . . . 9-18 Add-On Electrical Equipment . . . . . . . . . . . . . . . . . . . 9-47 Adding Equipment to the Airbag-Equipped Vehicle . . . . . 3-34 Adjustments Lumbar, Front Seats . . . . . . . . . . . 3-5 Air Cleaner/Filter, Engine . . . . . 10-13 Air Vents . . . . . . . . . . . . . . . . . . . . . . . 8-3 Airbag System Check . . . . . . . . . . . . . . . . . . . . . . . .
i-2 INDEX B Battery . . . . . . . . . . . . . . . . . . . . . . . 10-25 Jump Starting . . . . . . . . . . . . . . . 10-68 Power Protection . . . . . . . . . . . . . . 6-6 Voltage and Charging Messages . . . . . . . . . . . . . . . . . . .5-24 Blade Replacement, Wiper . . . 10-27 Bluetooth . . . . 7-19, 7-20, 7-23, 7-33 Brakes . . . . . . . . . . . . . . . . . . . . . . . . 10-23 Antilock . . . . . . . . . . . . . . . . . . . . . . .9-28 Assist . . . . . . . . . . . . . . . . . . . . . . . . .9-31 Fluid .
INDEX Circuit Breakers . . . . . . . . . . . . . . 10-33 Cleaning Exterior Care . . . . . . . . . . . . . . . 10-74 Interior Care . . . . . . . . . . . . . . . . 10-77 Climate Control Systems Dual Automatic . . . . . . . . . . . . . . . . 8-1 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Cluster, IP . . . . . . . . . . . . . . . . . . . . . . 5-7 Collision Damage Repair . . . . . . 13-9 Compact Spare Tire . . . . . . . . . . 10-67 Compass . . . . . . . . . . . . . . . . . . . . . . .
i-4 INDEX E E85 Fuel . . . . . . . . . . . . . . . . . . . . . . . 9-43 Electric Parking Brake Light . . . 5-15 Electrical Equipment, Add-On . . . . . . . . . . . . . . . . . . . . . . 9-47 Electrical System Engine Compartment Fuse Block . . . . . . . . . . . . . . . . 10-34 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . 10-33 Instrument Panel Fuse Block . . . . . . . . . . . . . . . . . . . . . . 10-37 Overload . . . . . . . . . . . . . . . . . . . 10-32 Electronic Stability Control . . .
INDEX Flat Tire, Changing . . . . . . . . . . . 10-61 Floor Mats . . . . . . . . . . . . . . . . . . . . 10-80 Fluid Automatic Transmission . . . . 10-13 Brakes . . . . . . . . . . . . . . . . . . . . . . 10-24 Power Steering . . . . . . . . . . . . . 10-21 Washer . . . . . . . . . . . . . . . . . . . . . 10-22 Fog Lamps Bulb Replacement . . . . . . 10-30, 6-4 Light . . . . . . . . . . . . . . . . . . . . . . . . . .5-20 Folding Mirrors . . . . . . . . . . . . . . . . 2-11 Front Seats Adjustment . . . . . .
i-6 INDEX H Halogen Bulbs . . . . . . . . . . . . . . . . 10-28 Hazard Warning Flashers . . . . . . . 6-3 Head Restraints . . . . . . . . . . . . . . . . 3-2 Headlamps Aiming . . . . . . . . . . . . . . . . . . . . . . 10-28 Automatic . . . . . . . . . . . . . . . . . . . . . . 6-3 Bulb Replacement . . . . . . . . . . 10-28 Daytime Running Lamps (DRL) . . . . . . . . . . . . . . . . . 6-2 Flash-to-Pass . . . . . . . . . . . . . . . . . . 6-2 High-Beam On Light . . . . . . . . . .
INDEX Lamps (cont.) License Plate . . . . . . . . . . . . . . . 10-31 Malfunction Indicator . . . . . . . . .5-12 On Reminder . . . . . . . . . . . . . . . . .5-20 Reading . . . . . . . . . . . . . . . . . . . . . . . 6-5 Lap-Shoulder Belt . . . . . . . . . . . . . 3-15 LATCH System Replacing Parts After a Crash . . . . . . . . . . . . . . . . . . . . . . .3-51 Latch, Lower Anchors and Tethers for Children . . . . . . . . . . 3-44 Light Electric Parking Brake . . . . . . . .
i-8 INDEX Messages (cont.) Tire . . . . . . . . . . . . . . . . . . . . . . . . . . .5-28 Transmission . . . . . . . . . . . . . . . . .5-28 Vehicle . . . . . . . . . . . . . . . . . . . . . . .5-24 Window . . . . . . . . . . . . . . . . . . . . . . .5-29 Mirrors Automatic Dimming Rearview . . . . . . . . . . . . . . . . . . . . 2-11 Convex . . . . . . . . . . . . . . . . . . . . . . .2-10 Folding . . . . . . . . . . . . . . . . . . . . . . . 2-11 Heated . . . . . . . . . . . . . . . . . . . . . . .
INDEX Power Door Locks . . . . . . . . . . . . . . . . . . . . 2-5 Mirrors . . . . . . . . . . . . . . . . . . . . . . . .2-10 Outlets . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Protection, Battery . . . . . . . . . . . . . 6-6 Retained Accessory (RAP) . . .9-18 Seat Adjustment . . . . . . . . . . . . . . . 3-4 Steering Fluid . . . . . . . . . . . . . . . 10-21 Windows . . . . . . . . . . . . . . . . . . . . .2-12 Pregnancy, Using Safety Belts . . . . . . . . . . . . . . . . . . . . . . . . .
i-10 INDEX Retained Accessory Power (RAP) . . . . . . . . . . . . . . . . . 9-18 Ride Control Systems . . . . . . . . . 9-33 Electronic Stability (ESC) . . . . .9-33 Messages . . . . . . . . . . . . . . . . . . . .5-27 Roadside Assistance Program . . . . . . . . . . . . . . . . . . . . . . 13-5 Roof Sunroof . . . . . . . . . . . . . . . . . . . . . . .2-15 Rotation, Tires . . . . . . . . . . . . . . . . 10-52 Routing, Engine Drive Belt . . . . . 12-4 Running the Vehicle While Parked . . . . . . . . . . .
INDEX Spare Tire Compact . . . . . . . . . . . . . . . . . . . . 10-67 Specifications and Capacities . . . . . . . . . . . . . . . . . . . . 12-2 Speedometer . . . . . . . . . . . . . . . . . . . 5-8 Start Assist, Hills . . . . . . . . . . . . . . 9-31 Starter Switch Check . . . . . . . . . 10-25 Starting the Engine . . . . . . . . . . . . 9-18 Steering . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Fluid, Power . . . . . . . . . . . . . . . . 10-21 Wheel Adjustment . . . . . . . . . . . . .
i-12 INDEX Towing General Information . . . . . . . . . .9-46 Recreational Vehicle . . . . . . . . 10-72 Vehicle . . . . . . . . . . . . . . . . . . . . . 10-71 Traction Control System (TCS) . . . . . . . .9-31 Off Light . . . . . . . . . . . . . . . . . . . . . .5-16 Transmission Automatic . . . . . . . . . . . . . . . . . . . . .9-24 Fluid, Automatic . . . . . . . . . . . . 10-13 Messages . . . . . . . . . . . . . . . . . . . .5-28 Transportation Program, Courtesy . . . . . . . . . . . . . . . . . . . .
