Specifications

19 Quick Start Guide18 BUGERA TRIREC INFINIUM
bugera-amps.com bugera-amps.com
Step 3: Getting started
BUGERA TRIREC INFINIUM Getting started
Make all appropriate audio and power
connections to the TRIREC. Leave the
power for all devices o!
Turn the MASTER knob all the way down.
Leaving the STANDBY switch in the down/
o position, ip the POWER switch up to
turn the ampon.
Turn on any other devices connected to
the amp.
Select the RECTIFIER setting on the back
panel. Silicon diodes have the highest
power output and tightest bass response,
while rectier valves have a lower output but
produce a touch-response that many guitarists
prefer. A combination of the two can also
beselected.
After the POWER switch has been engaged
for atleast one minute, ip the STANDBY
switch up.
Turn the MASTER knob up to the 9:00
position tostart.
Select one of the 3 channels using
theCHANNEL buttons or the
FSB106Afootswitch.
Turn the VOLUME knob up half way on the
selectedchannel.
Select the basic tonal character using the
channel’s MODE switch.
Adjust the amount of distortion using the
GAIN knob. Depending on EQ and volume
settings, too much gain can
causefeedback.
Adjust the equalization using the TREBLE,
MID, BASS and PRESENCE knobs.
Repeat steps 8-12 for the other channels.
Use each channel's VOLUME knob to
balance the output levels between them.
Engage the REVERB function and adjust
the amount of desired eect. To reset
the Reverb to default settings, press the
REVERB button within the rst few
seconds of powering the amp on.
Adjust the VARIPOWER knob
counterclockwise to achieve power valve
saturation at lower volume settings. Turn
the VARIPOWER knob fully clockwise when no
power reduction is required. This setting allows the
MASTER volume knob to operate normally and
produce the maximum output.
Engage the BOOST function and adjust
the BOOST knob to achieve the desired
amount of volume boost for solo sections
during aperformance.
If using eects in the FX LOOP, set the
ASSIGN knob to ON if you want the loop
constantly active, or REMOTE if you want
to control the on/o status with the FSB106A
footswitch. TheCHANNEL setting allows you to
continually control the loop via footswitch,
butsaves the on/o status of the FX LOOP,
BOOSTand REVERB (including Decay and Send
levels) for each channel. If you are not using the
FXLOOP, setthe ASSIGN knob to OFF.
Adjust the SEND and LEVEL knobs to
achieve an optimal FX LOOP signal level
going to the processor and returning to
the amp. Make sure the volume level is consistent
when turning the FX LOOP onand o.
Rock out and have fun!
MIDI Implementation
CC12 FX LOOP (x00, x01)
CC13 BOOST (x00, x01)
CC75 REVERB DECAY (0-7)
Stored per channel when FX LOOP
ASSIGN is “Channel”
Default DECAY setting is 3
Note: changing DECAY resets
REVERBSEND to 127
CC91 REVERB SEND (continuous, 0-127)
Stored per channel when FX LOOP
ASSIGN is “Channel”
Reset to default REVERB SEND (127)
bypressing REVERB during power up
CC120 MUTE
PGM 001 CH 1
PGM 002 CH 2
PGM 003 CH 3
PGM 011 CH 1 + BOOST o
PGM 012 CH 2 + BOOST o
PGM 013 CH 3 + BOOST o
PGM 021 CH 1 + BOOST on
PGM 022 CH 2 + BOOST on
PGM 023 CH 3 + BOOST on
Default MIDI channel = 1
Hold one of the FSB106A footswitches1-6
during power up to select the
MIDIchannel01-06accordingly.