BUFFALO TECHNOLOGY AIR STATION INSTALLATION GUIDES Address: 4030 W. Braker Ln. Suite 350 Austin, TX. 78759 Website: www.buffalotech.com Email: Sales - sales@buffalotech.com Technical Support - info@buffalotech.com Phone: Sales Tel - 512-794-8533 Sales Tel - 800-688-7466 Sales Fax - 512-794-8520 Tech Support Line - 800.934.
1 TABLE OF CONTENTS SECTION Page OVERVIEW FOR ADVANCED USERS…………….…………………………………….…….2 1. WINDOWS 9x and ME INSTALLATION………………………………………….……….…..3 1.1 Installation Instructions for PCI-Adapter card.………………………..……..……….3 1.2 Installation Instructions for PMCIA wireless Card.…….……………….……………7 1.3 Installation Instructions for Client Manager………..………………………….. ……11 2. WINDOWS 2000 INSTALLATION………………………………………………………. . …..15 2.1 Updating the PCI-Adapter card driver……….………………………………… …….16 2.
2 Overview for Advanced Users 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Upgrade or install the PCI adapter (for desktops) driver to “Buffalo” from the “\PCIOP” directory on your CD-ROM. Run “\PCIOP\SETUP.EXE” for Windows NT Install the PCMCIA card drivers from the “\PCML11” directory on your CD-ROM . Install the ESS-ID driver for Windows NT and Windows 2000 from the “\ESSIDDRV” directory on your CD-ROM.
3 1. WINDOWS 9x and ME INSTALLATION 1.1 Installation Instructions for PCI Adapter Cards If you have a laptop, skip this instruction and go to the Installation Instruction for the PMCIA Wireless Card on page 6 1. Turn off your computer and disconnect the power cable. 2. Remove the computer cover.
4 3. 4. 5. Install the PCI Adapter card into one of the empty PCI slots. Replace the computer cover. Turn on your computer. The Windows 98 Add New Hardware Wizard automatically detects the PCI-Adapter card and attempts to locate the driver media provided by the manufacturer. Insert the AirStation installation CD. You will see a dialog box like the one below. 6. Click the Next Button.
5 7. Select Search For the Best Driver For Your Device (Recommended) and click Next. 8. Clear all the check boxes and check only the Specify a Location check box. Type or click the Browse button and point to the driver path: E:\PCIOP\WIN98. (E: represents your CD-ROM drive). Click the Next button. 9. Windows 98 will begin installing the drivers. A dialog screen will come up with the message Win 98 could not find the WLIpci.vxd.
6 10. If you are prompted to insert your Windows 98 disk, type or click the Browse button and point to the driver path: E:\WIN98. (E: represents your CD-ROM drive) then Click OK. You will then see a dialog box like the one below. 11. Click the Finish Button when the installation is complete. 12. Restart your computer for the changes to take effect.
7 1.2 Installation Instruction for the PCMCIA Wireless Card 1. Insert the PCMCIA card into the PCI adapter slot. The Windows 98 Add New Hardware Wizard automatically detects the PCMCIA card and attempts to locate the driver for it. Insert the Air Station installation CD. You will then see a dialog box like the one below. 2. Click the Next button.
8 3. Select Search For the Best Driver For Your Device (Recommended) and click Next 4. Clear all the check boxes and check only the Specify a Location check box. Type or click the Browse button and point to the driver path: E:\PCML11\WIN98. (E: represents your CD-ROM drive) then click the Next button. 5. 6. Click the Next button to install the Windows 98 drivers. Windows 98 will begin installing the drivers. A dialog screen will come up with the message Win 98 could not find the WLI11ins.dll.
9 You will then see a dialog box like the one below. 7. 8. 9. 10. 11. 12. 13. 14. If you are using the WLI-PCI-OP together (desktop), click Yes. If your system is a laptop or you use the WLI-ISA-OP together, click No. Windows 98 will complete installing the Drivers. If you are prompted to insert your Windows 98 disk, type or click the Browse button and point to the driver path: E:\WIN98. (E: represents your CD-ROM drive) then click OK. Click the Finish button when the installation is complete.
10 16. Click the Basic Setting tab. 17. In the ESS ID Textbox, type the word “ANY” or if you have more than one Airstation Accesspoint, input the last six characters of the MAC address and the word “GROUP”, with no space between them. The Media Access Control (MAC) address can be found on the back of the Airstation Accesspoint. For example, if the Mac Address is 004026 8A9090, then the last six characters of this number (8A9090) will be the MAC address. Please note that it is case sensitive, i.e.
11 1.3 INSTALLING CLIENT MANAGER 1. 2. 3. Insert your Air Station Driver CD in your CD-ROM drive. Double-click the my computer icon on your desktop. Double-click on your CD-ROM drive. 4. Double-click the wleasy.exe file in the current folder on your CD-ROM drive. 5. Select Install the Client Manager.[C] and click the Next button. 6. Exit any Applications currently running and Click OK The Client Manager Installer will begin.
12 7. Click the Next Button. 8. Click the Next Button. 9. Click the Start Button.
13 10. The Client Manager Files will be installed on Your System. We recommend you click No when prompted to add Client Manager to your Startup Menu. 11. Click OK to complete the installation. 12. Restart your system when the installation is complete for the new settings to take effect. 13. Click Start on the taskbar. Select Programs from the Start menu. Select Melco Wireless LAN and then select Client Manager. The Client Manager Window will open. 14.
14 15. Type the word “ANY” or if you have more than one Airstation Accesspoint on your network, input the last six characters of the MAC address of the specific Airstation Accesspoint you want to connect to . The Media Access Control (MAC) address can be found on the back of the Airstation Accesspoint. For example, if the Mac Address is 004026 8A9090, then the last six characters of this number (8A9090) will be the MAC address. Please note that it is case sensitive, i.e.
15 2. WINDOWS 2000 INSTALLATION Before you start, we recommend you install the latest service pack. 1. Turn off your computer and disconnect the power cable. 2. Remove the computer cover. 3. 4. 5. 6. 7. Install the PCI Adapter card into one of the empty PCI slots. Replace the computer cover. Reconnect the power cable.
16 2.1 UPDATING PCI-ADAPTER CARD DRIVER 1. 2. 3. 4. Click Start on the taskbar, and select Settings from the Start menu Select Control panel, and the Control Panel group will appear Double-click the System icon and click the Hardware tab Click the Device Manager button. 5. Make sure the following device name is listed in the PCMCIA Adaptors. WLI-PCI-OP: Ricoh R/RL/RT/RC/5C475(II),R5C520 or Compatible CardBus Controller.
17 9. Select Search for The Best Driver For Your Device (Recommended) option and click Next. 10. Type or click the Browse button and point to the driver path: E:\PCIOP\WIN2000. (E: represents your CD-ROM drive) and then click Next. 11. Select Install one of the other drivers and then click Next. 12. Select BUFFALO WLI-PCI-OP Bridge. 13. Click the Next button to install the driver. 14. Click the Finish button when the installation is complete. 15. Click the Close button. 16.
18 2.2 1. 2. 3. 4. INSTALLATION INSTRUCTIONS FOR PCMCIA CARD Insert the PCMCIA card into the Adapter card you just installed. If this is a laptop computer, insert the PMCIA card into an available slot. Log on as the Administrator. The Windows 2000 Add New Hardware Wizard automatically detects the Adapter card and attempts to locate the driver media provided by the manufacturer. Insert the installation disk and click Next.
19 5. Clear all check boxes and check only the Specify a Location check box. Click Next. 6. Click the Browse button and point to the driver path E:\PCML11\Win2000. (E: represents your CD-ROM drive) then click OK. Click Next to install the Windows 2000 drivers. 7.
20 8. 9. This dialogue box will appear. Answer the question Do you want to continue the installation? by clicking Yes. Click the Finish button when the installation is complete.
21 2.3 CONFIGURING YOUR NEW LAN CARD You will now see an Icon in your systray at the bottom of your taskbar that looks like two computers with a red X through them. 1. Right-click the icon and select Network and Dial Up Connections. 2. Double-click the Local Area Connection for the Melco Wireless LAN. 3. In the Local Area Connection properties dialog box, click the Configure button for the Melco Wireless Adapter. 4. Click the Advanced tab.
22 5. 6. 7. 8. 9. If you are using a PCI-adapter (i.e. Desktop), select the WLI-PCI mode and make sure it is set to ON otherwise if you are using a laptop, set it to OFF. Select the Station name property and type the word “ANY” or if you have more than one Airstation Accesspoint , type the last six characters of the Airstation Accesspoint MAC address following by the word “GROUP”, with no space between them in the value textbox. All alphabetical characters need to be capitalized.
23 10. Configure your TCP/IP protocol for your LAN setup. If you do not know your LAN setup, consult your users manual or system administrator. 11. Click OK. 12. Click the install button. 13. Select Service and click the Add button. 14. Click Have disk. Type or click the Browse button and point to the driver path: E:\ESSIDDRV\WIN2000. (E: represents your CD-ROM drive) 15. Click OK. 16. If you are prompted to Click the Network Service that you want to install.
24 17. Click on the Melco Essid service and then click OK. 18. Restart your computer for the new settings to take effect. 19. Install the Client Manager.
25 2.4 INSTALLING CLIENT MANAGER 1. 2. 3. Insert your Air Station Driver CD in your CD-ROM drive. Double-click the my computer icon on your desktop. Double-click on your CD-ROM drive. 4. Double-click the wleasy.exe file in the current folder on your CD-ROM drive. 5. Select Install the Client Manager.[C] and click the Next button. 6. Exit any Applications currently running and Click OK. The Client Manager Installer will begin.
26 7. Click the Next Button. 8. Click the Next Button. 9. Click the Start Button.
27 10. The Client Manager Files will be installed on Your System. We recommend you click No when prompted to add Client Manager to your Startup Menu. 11. Click OK to complete the installation. 12. Restart your system when the installation is complete for the new settings to take effect. 13. Click Start on the taskbar. Select Programs from the Start menu. Select Melco Wireless LAN and then select Client Manager. The Client Manager Window will open. 14.
28 15. Type the word “ANY” or if you have more than one Airstation Accesspoint on your network, input the last six characters of the MAC address of the specific Airstation Accesspoint you want to connect to. The Media Access Control (MAC) address can be found on the back of the Airstation Accesspoint. For example, if the Mac Address is 004026 8A9090, then the last six characters of this number (8A9090) will be the MAC address. Please note that it is case sensitive, i.e.
29 WINDOWS NT 4.0 INSTALLATION 3. Before you start, you must make sure you have Windows NT 4.0 with the latest service pack. If you are using a Laptop, please refer to “Installation instructions for PCMCIA wireless card” section, page 19. 1. Turn off your computer, and disconnect the power cable. 2. Remove the computer cover.
30 3. 4. 5. Install the PCI Adapter card into one of the empty PCI slots. Replace the computer cover. Reconnect the power cable. 6. 7. 8. Insert the PCMCIA card in the PCI Adapter card you just installed. Turn on your computer. Log on as the Administrator. 3.1 Installation for PCI Adapter Cards 1. 2. 3. 4. 5. 6. 3.2 Put the Air Station CD in the CD-ROM drive. Double-click My Computer. Double-click the CD-ROM drive. Double-click the PCI-OP folder. Double-click the Setup.exe icon.
31 7. 8. 9. 10. 11. 12. 13. Type your CD-ROM drive letter and then PCML11\Winnt. It should look something like this (E:\PCIL11\Winnt). A dialog box will come up with Melco WLI-PCM-L11 wireless LAN adapter highlighted. Click OK. You will then see a WLI-PCM-L11 configuration box. Click the Basic settings tab. Check the infrastructure mode checkbox. Check the WLI-PCI-L11 mode checkbox if using a PCI-adapter card. The ESSID textbox will then ungray.
32 14. Click OK. 15. Click close when you see Melco WLI-PCM-L11 wireless LAN adapter in the configuration box. 16. A TCP/IP configuration box will appear. 17. Verify that the MELCO WLI-PCM-L11 Wireless LAN Adapter is selected in the adapter text box. 18. Select Specify an IP address and input the IP address and subnet mask below. IP address: 192.168.0.2 Subnet Mask: 255. 255. 255. 0 19. Click OK. 20.
33 3.3 1. 2. 3. 4. 5. 6. 7. 8. 9. Installing the ESS-ID Settings Driver Click Start on the taskbar, and select settings from the Start menu. Select Control panel, and the Control Panel group appears. Double-click the Network icon. In the Network dialog box, Select Service and click the Add button. Click Have Disk and in the specified location area type in your CD-ROM drive letter followed by a colon and ESSIDDRV\WINNT. You should have E:\ESSIDDRV\WINNT where E represents your drive letter. Click OK.
34 3.4 Troubleshooting Windows NT4.0 has a standard diagnostics program that checks to verify if the WLI-PCM-L11 has been installed correctly. Follow the steps below to perform this check. 1. 2. 3. Click the Start on the taskbar, and select Settings from the Start menu. Select Control Panel. The Control Panel group appears. Double-click the PC CARD [PCMCIA] icon. Verify that the PCMCIA Card is installed. Close the Control Panel.
35 12. 13. 14. 15. 16. 17. Click OK to close the WliL11 properties dialog box. Click OK to close the Windows NT Diagnostics Dialog box. Click the Start on the taskbar, and select Settings from the Start menu. Select Control Panel. The Control Panel group appears. Double-click the Devices icon. Verify that the status for the MELCO Wireless LAN Card is started and that the Startup setting is Automatic. 18. Verify that the status for PCMCIA under devices is started and that the startup setting is Automatic.
36 23. Install the Client Manager. 3.5 Changing Resource Settings Follow the steps below if you need to change the settings for the WLI-PCM-L11 (IRQ level, I/O port address). 1. 2. 3. Click Start on the taskbar, and select settings from the Start menu. Select Control panel, and the Control Panel group appears. Double-click the Network icon. 4. Click the Adapters tab. Select MELCO WLI-PCM-L11 Wireless LAN Adapter and click the Properties button. 5. Click the Adapters tab.
37 6. 7. The current settings for the WLI-PCM (IRQ level, I/O port address) are displayed. Change the settings as required and click the OK button. Refer to your users manual for which parameters to change. Restart the computer so that the new settings will take effect.
38 3.6 INSTALLING CLIENT MANAGER 1. 2. 3. Insert your Air Station Driver CD in your CD-ROM drive. Double-click the my computer icon on your desktop. Double-click on your CD-ROM drive. 4. Double-click the wleasy.exe file in the current folder on your CD-ROM drive. 5. Select Install the Client Manager.[C] and click the Next button. 6. Exit any Applications currently running and Click OK The Client Manager Installer will begin.
39 7. Click the Next Button. 8. Click the Next Button. 9. Click the Start Button.
40 10. The Client Manager Files will be installed on Your System. We recommend you click No when prompted to add Client Manager to your Startup Menu. 11. Click OK to complete the installation. 12. Restart your system when the installation is complete for the new settings to take effect. 13. Click Start on the taskbar. Select Programs from the Start menu. Select Melco Wireless LAN and then select Client Manager. The Client Manager Window will open. 14.
41 15. Type the word “ANY” or if you have more than one Airstation Accesspoint , input the last six characters of the MAC address and the word “GROUP”, with no space between them. The Media Access Control (MAC) address can be found on the back of the Airstation Accesspoint. For example, if the Mac Address is 004026 8A9090, then the last six characters of this number (8A9090) will be the MAC address. Please note that it is case sensitive, i.e.
42 4. CONFIGURING THE AIRSTATION STANDARD MODEL WLA-L11 After installing the Client Manager, you should be connected to the Airstation Accesspoint and should be fully functional. You have a default IP address of 1.1.1.1. If you need to change the IP address, install the Airstation Manager. INSTALLING AIRSTATION MANAGER 1. 2. 3. Insert your Air Station Driver CD in your CD-ROM drive. Double-click the my computer icon on your desktop. Double-click on your CD-ROM drive. 4. Double-click the wleasy.
43 6. Exit any applications you have running and then Click OK. The AirStation Manager Installer will begin. 7. Click the Next Button. 8. Click the Next Button 9. Click the Start button.
44 The AirStation Manager Files will be installed on your system. 10. Click OK to complete the installation. 11. Restart your system when the installation is complete for the new settings to take effect. 12. Click Start on the taskbar. Select Programs from the Start menu. Select Melco Airstation and then select AirStation Manager. The AirStation Manager Window will open. 13. Click the search icon on your toolbar. 14. The AirStation Manager will search for the Airstation Accesspoint on the Network.
45 15. To change the IP Address settings for your Airstation Accesspoint, select the AirStation. In the Admin Menu, select IP Address and change it accordingly. Click OK.
46 5. CONFIGURING THE AIRSTATION ROUTER MODEL WLAR-L11 5.1 CHANGING TCI/IP SETTINGS IN WINDOWS 98 OR ME Your Airstation Accesspoint is a Bridge with an IP Address of 1.1.1.1 by default. In order for you to connect to the Airstation Accesspoint and convert it to a Router, we recommend that you change your computer’s TCP/IP settings to the static Address 192.168.0.2 and that you configure the Router’s IP Address to 192.168.0.1. 1. 2. 3. 4.
47 2. Select Specify an IP address and input the IP address and subnet mask below. IP address: 192.168.0.2 Subnet Mask: 255. 255. 255. 0 3. Select the Gateway tab and remove all the installed gateways if there are any.
48 4. 5. 6. Select the DNS Configuration tab and select Disable DNS. Click OK to close the TCP/IP Properties dialog box. Click OK to close the Network Properties dialog box. 7. If you are using the WLI-PCI-OP, then click Yes. If your computer is a laptop or you use the WLI-ISA-OP, click No. Restart your Computer for the new settings to take effect 8.
49 5.2 CHANGING TCI/IP SETTINGS IN WINDOWS 2000 Your Airstation Accesspoint is a Bridge with an IP Address of 1.1.1.1 by default. In order for you to connect to the Airstation Accesspoint and convert it to a Router, we recommend that you change your computer’s TCP/IP settings to the static Address 192.168.0.2 and that you configure the Router’s IP Address to 192.168.0.1. 1. Click Start on the taskbar, and select Settings from the Start menu. 2. Select Control panel, and the Control Panel group appears.
50 6. Select Internet Protocol (TCP/IP) and then click the Properties button. 7. Select Specify an IP address and input the IP address and subnet mask below. IP address: 192.168.0.2 Subnet Mask: 255. 255. 255. 0 8. 9. 10. 11. Click OK to close the Internet Protocol (TCP/IP) Properties dialog box Click OK to close the Local Area Connection Properties dialog box Click the Close Button to close the Local Area Connection Status Dialog Box Restart your computer for the new settings to take effect.
51 5.3 CHANGING TCI/IP SETTINGS IN WINDOWS NT 4.0 Your Airstation Accesspoint is a Bridge with an IP Address of 1.1.1.1 by default. In order for you to connect to the Airstation Accesspoint and convert it to a Router, we recommend that you change your computer’s TCP/IP settings to the static Address 192.168.0.2 and that you configure the Router’s IP Address to 192.168.0.1. 1. 2. 3. Click Start on the taskbar, and select Settings from the Start menu.
52 5. Select TCP/IP Protocol and click the Properties button. 6. 7. Verify that the MELCO WLI-PCM-L11 Wireless LAN Adapter is selected. Selecting Specify an IP address and input the IP address and subnet mask below. IP address: 192.168.0.2 Subnet Mask: 255. 255. 255. 0 8. 9. Click OK Click OK to Close the Network Dialog Box 10. Restart your computer for the new settings to take effect.
53 5.4 INSTALLING AIRSTATION MANAGER 1. 2. 3. Insert your Air Station Driver CD in your CD-ROM drive. Double-click the my computer icon on your desktop. Double-click on your CD-ROM drive. 4. Double-click the wleasy.exe file in the current folder on your CD-ROM drive. 5. Select Install the AirStation Manager.[A] and click the Next button. 6. Exit any applications you have running and then Click OK. The AirStation Manager Installer will begin.
54 7. Click the Next Button. 8. Click the Next Button 9. Click the Start button. The AirStation Manager Files will be installed on your system.
55 10. Click OK to complete the installation. 11. Restart your system when the installation is complete for the new settings to take effect. 12. Click Start on the taskbar. Select Programs from the Start menu. Select Melco Airstation and then select AirStation Manager. The AirStation Manager Window will open. 13. Click the search icon in the AirStation Manager toolbar to connect to the Airstation Accesspoint. 14. The AirStation Manager will search for the Airstation Accesspoint on the Network.
56 15. To change the IP Address settings for your Airstation Accesspoint , select the AirStation. In the Admin Menu, select IP Address and configure your IP settings to 192.168.0.1. Click OK. 16. To change configuration settings, select the AirStation. In the Admin Menu, select Configure AS. 17. Click the Wizard Settings button. 9. A password request page will pop up. Type root in the User Name field, but leave the password field blank, and then click OK.
57 10. Select Connect to CATV Internet and click the Next Setup Menu Button. 11. 12. 13. 14. Select Automatic IP Assignment by DHCP Server and click the set button. Click the set button. Setting completed will be displayed. Close the Web browser. You then need to change your computers TCP/IP settings back to “Obtain an IP Address automatically”. For any additional wireless workstations, you only need to install the Client Manager and configure the IP address to be assigned automatically by DHCP.
58 6. CONFIGURING THE AIRSTATION LOCAL ROUTER MODEL WLAR-L11-L 6.1 CHANGING TCI/IP SETTINGS IN WINDOWS 98 OR ME Your Airstation Accesspoint is a Router with an IP Address of 192.168.0.1 by default. In order for you to connect to your Airstation Accesspoint, we recommend that you change your computer’s TCP/IP settings to the static address 192.168.0.2. 1. 2. 3. 4. Click Start on the taskbar, and select Settings from the Start menu. Select Control panel, and the Control Panel group appears.
59 6. Select Specify an IP address and input the IP address and subnet mask below. IP address: 192.168.0.2 Subnet Mask: 255. 255. 255. 0 7. Select the Gateway tab and remove all the installed gateways if there are any.
60 8. Select the DNS Configuration tab and select Disable DNS. 9. Click OK to close the TCP/IP Properties dialog box. 10. Click OK to close the Network Properties dialog box. 11. If you are using the WLI-PCI-OP, then click Yes. If your computer is a laptop or you use the WLI-ISA-OP, click No. 12.
61 6.2 CHANGING TCI/IP SETTINGS IN WINDOWS 2000 Your Airstation Accesspoint is a Router with an IP Address of 192.168.0.1 by default. In order for you to connect to your Airstation Accesspoint, we recommend that you change your computer’s TCP/IP settings to the static address 192.168.0.2. 1. Click Start on the taskbar, and select Settings from the Start menu. 2. Select Control panel, and the Control Panel group appears. 3. Double-click the Network and Dial-up Connection Icon. 4.
62 6. Select Internet Protocol (TCP/IP) and then click the Properties button. 7. Select Specify an IP address and input the IP address and subnet mask below. IP address: 192.168.0.2 Subnet Mask: 255. 255. 255. 0 8. 9. 10. 11. Click OK to close the Internet Protocol (TCP/IP) Properties dialog box Click OK to close the Local Area Connection Properties dialog box Click the Close Button to close the Local Area Connection Status Dialog Box Restart your computer for the new settings to take effect.
63 6.3 CHANGING TCI/IP SETTINGS IN WINDOWS NT 4.0 Your Airstation Accesspoint is a Router with an IP Address of 192.168.0.1 by default. In order for you to connect to your Airstation Accesspoint, we recommend that you change your computer’s TCP/IP settings to the static address 192.168.0.2. 1. 2. 3. Click Start on the taskbar, and select Settings from the Start menu. Select Control panel, and the Control Panel group appears. Double-click the Network Icon. 4. Click the Protocols Tab 5.
64 6. 7. Verify that the MELCO WLI-PCM-L11 Wireless LAN Adapter is selected. Select Specify an IP address and input the IP address and subnet mask below. IP address: 192.168.0.2 Subnet Mask: 255. 255. 255. 0 8. 9. Click OK Click OK to Close the Network Dialog Box 10. Restart your computer for the new settings to take effect.
65 6.4 INSTALLING AIRSTATION MANAGER 1. 2. 3. Insert your Air Station Driver CD in your CD-ROM drive. Double-click the my computer icon on your desktop. Double-click on your CD-ROM drive. 4. Double-click the wleasy.exe file in the current folder on your CD-ROM drive. 5. Select Install the AirStation Manager.[A] and click the Next button. 6. Exit any applications you have running and then Click OK. The AirStation Manager Installer will begin.
66 7. Click the Next Button. 8. Click the Next Button 9. Click the Start button. The AirStation Manager Files will be installed on your system.
67 10. Click OK to complete the installation. 11. Restart your system when the installation is complete for the new settings to take effect. 12. Click Start on the taskbar. Select Programs from the Start menu. Select Melco Airstation and then select AirStation Manager. The AirStation Manager Window will open. 13. Click the search icon in the Airstation Manager toolbar to connect to the Airstation Accesspoint. 14. The AirStation Manager will search for the Airstation Accesspoint on the Network.
68 15. To change the IP Address settings for your Airstation Accesspoint , select the AirStation. In the Admin Menu, select IP Address and configure your IP settings to 192.168.0.1. Click OK. 16. To change configuration settings, select the AirStation. In the Admin Menu, select Configure AS. 17. 18. 19. 20. 15. Click the Standard Setup button. Select Automatic IP Assignment by DHCP Server Select Use automatic IP address assignment for LAN and then click the set button. Setting completed will be displayed.
69 6.5 PPTP SETUP For WLAR-L11-L model If you do not see the [Protocol Number] option, please visit our web site at www.buffalotech.com for free firmware upgrade PPTP (Point-to-Point Tunneling Protocol) is a protocol (set of communication rules) that allows corporations to extend their own corporate network through private "tunnels" over the Internet. Effectively, a corporation uses a wide-area network as a single large local area network.
70 5. Click Return and verify that the NAT Table address for IP address of LAN appears to be the IP address of the LAN computer. 6. Your Airstation AccessPoint is now set to allow all Protocols to pass through for your computer. 7.
71 6.6 PPPoE SETUP FOR WLAR-L11-L MODEL If you do not see the PPPoE option, please visit our web site at www.buffalotech.com for a free firmware upgrade The Point-to-Point Protocol over Ethernet ( PPPoE), is a peer-to-peer protocol used on an Ethernet Network, instead of a regular phone line. Some ISPs require PPPoE in order for customers to connect to the Internet. Please consult your Internet service provider to determine your requirement.
72 11. Input the “User Name” and “password” given by your Internet service provider. Reenter the “password” in the “confirm” textbox and then click Set. 12. Click Return and then Click Basic. The basic setting screen will be shown. 13. Select use the PPPoE client function for the WAN-side IP address acquisition method, and then click set. The Setting will be completed and the Airstation Accesspoint will be rebooted. 14.
73 6.7 Glossary of Terms Used in the PPPoE settings User Name – This is the user specified name that is to be recognized by your Internet service provider. Up to 64 letters are permissible. Password - This is the user specified password that is to be recognized by your Internet service provider. Use the same password in the “confirm” box. Up to 64 letters are permissible. Service Name - If more than 2 PPPoE servers exist in the system, a specific server can be selected for providing your PPPoE service.
74 7. CONFIGURING THE AIRSTATION ANALOG MODEM MODEL WLAR-L11-M Your Airstation Accesspoint has an IP address of 1.1.1.1 by default. In order for you to connect to the Airstation Accesspoint, we recommend that you change your computer’s TCP/IP settings to the static address 192.168.0.2 and configure your Airstation’s IP address to 192.168.0.1. 1. Please follow the WLAR-L11 instruction until you see the Admin Menu below and following the rest of the instructions on this page. 2.
75 4. Select Connecting to the Internet via Internal modem and click the Next Setup Menu Button. 5. Input the necessary items and click Set Button. For any additional wireless workstation, you only need to install the Client Manager and configure the IP address to be assigned automatically by DHCP.
76 8. Apple Installation Your Apple Computer must either have an Airport card or PCMCIA wirelesses card that is 802.11b compliant installed. 1. Turn on your Computer. 2. Click the Apple icon on your toolbar and Select Airport. 3. In the Airport Network window, select Network area. 4. Find a 6-character ID number with the word GROUP attached to it and click it. 5. Click the Apple icon on your toolbar. Select Control Panel, and then click TCP/IP. 6.
77 Address: 1977 W. 190th Street Suite 100 Torrance, CA 90504 Website: www.buffalotech.com Email: Sales - sales@buffalotech.com Technical Support - info@buffalotech.com Phone: Sale Tel - 310-965-0448 Sale Tel - 800-508-1110 Sale Fax - 310-965-0497 Tech Support Line - 800.934.
78 78
