How-To Guide

How to Get the Right Fit
1. Grab the top of the ear you are
puing the earbud in with your
opposite hand and gently pull up and
back towards the rear of your head.
2. Grab the earbud with the other
hand, forefinger and thumb, and
slide the earbud into the ear canal.
To help facilitate this, some back
and forth rotation of the earbud
while it is being inserted can help. It
may also help to open your mouth,
which opens your ear canal for
easier insertion.
3. The earbud should have a snug
and comfortable fit, but should not
sound like you are underwater! If
you feel like you are swimming, pull
the earbud out a lile while still
maintaining fit in the ear.
• Charge the earbuds by connecting a standard USB charger into the dongle.
When the earbuds are fully charged and ready for use, the LED light will show
as green.
• We did not include a charger in your packaging because most people have
them and we are working to stay true to our “green” philosophy of less
waste! However, if you need one, just email us at TheTeam@Buderflys.com and
we will make sure you get one.
CABLE OVERVIEW
Buon Desired Outcome Action
Vol +
Volume Up Normally Single press
Next Track Long press (1 sec.)
Vol -
Volume Down Normally Single press
Previous Track Long press (1 sec.)
Power
Power ON Long press (2 sec.)
Power OFF Extended long press (4 sec.)
Music Play/Pause Single press
Receive Incoming Call Single press upon incoming call
Reject Incoming Call Long press (1 sec.) upon incoming call
Cancel/End Active Call Single press
Reconnect to Last Device Single press
Voice Search/Siri Long press (3 sec.)
Vol + & Vol - Pair/Clear Paired Device List Very long press (5 sec.)
Our patent pending buds are technically in ear monitors, which means they take a
lile work to ensure they are properly in your ear. However, once in correctly, they
stay snug and comfortable all day long. They also become more comfortable the
longer you wear them as they warm to your body heat. Below are standard directions
we provide to properly fit the bud in your ear - however, we also provide a tutorial
on our website and are always happy to answer any questions. Just email us at
TheTeam@Buderflys.com or reach out on our website.
To see more specifics on buon functionality and LED indications on your
cable, please visit Buderflys.com FAQ page
HOW TO INSERT INTO YOUR EAR
Connecting & Disconnecting Your Bluetooth Cable
The ends of each tether (Bluetooth dongle) are terminated with an
Estron T2 Talon connector. This aachment allows for the tether to
be detached and reaached, as follows:
1. Identify which cable is the le and right by the “L” and the “R”
at the tip of the cable and match to the appropriate earbud.
2. Insert the cable by pushing the cable directly into the
earbud socket.
3. If the dongle needs recharged yet you wish to continue listening
to your earbuds, remove the tether and plug in your hard wired
cables if you have purchased these.
4. To disconnect the cable from the earplug, hold onto the earplug
and pull the cable straight in the direction that the cable is aached.
5. If it is hard to disconnect the plug, try to rotate the plug while
pulling out straight. Be careful not to rock or angle the plug, which
can cause damage.
T2 TALON USE AND CONNECTIONS
1. Hold down the power buon for 5 seconds. The indicator light
located on the side next to the USB charging port will begin
flashing red and blue to indicate the pairing process has begun.
2. To activate Bluetooth on your device and set it to search for
new devices, follow the steps below:*
• iPhone: Go to Seings > General > Bluetooth >On
• Android: Go to Settings > Bluetooth >On > Scan for Devices
• Windows: Go to Seings > Bluetooth > On
* Pairing steps can vary by device.
SYNCING WITH YOUR DEVICE
3. From the displayed device list, select “Buderflys Curiosity G2.”
4. If your device asks for a passcode, enter four zeros (0000) for the passcode or
accept the connection.
5. Once successfully paired, you will hear a single beep through the earphones and the
indicator light switches from flashing red and blue to just show a slow flashing blue.