User's Manual

WŽǁĞƌƵƚ-KĨĨŵŽĚĞ
- The Budderfly switches have the ability to completely disconnect the power from the load.
- Pressing ƚŚĞƚŽƉŽĨƚŚĞƌŽĐŬĞƌĨŽƌϭϱƐĞĐŽŶĚƐǁŝůůĂĐƚŝǀĂƚĞƚŚĞWŽǁĞƌƵƚ-ŽĨĨĨĞĂƚƵƌĞƚŚĞůŽĂĚǁŝůůďĞƚƵƌŶĞĚŽĨĨ
- The Status LED will start blinking to indicate that the load is disconnected and the switch is in the Power Cut-off mode.
- tŚĞŶƚŚĞWŽǁĞƌƵƚ-ŽĨĨ mode is activated, the switch cannot be turned on through software and cannot be turned on
physically.
- Pressing the Bottom of the rocker again for 15 seconds will de-ĂĐƚŝǀĂƚĞƚŚĞWŽǁĞƌƵƚ-ŽĨĨŵŽĚĞĂŶĚƚŚĞĚĞǀŝĐĞǁŝůůŐŽ
back to the normal state.
Features:
- Remote On/Off control
- Manual On/Off control
- No neutral required
On/Off Control:
- Remote Control:
o The Budderfly switches can be controlled remotely thru the Budderfly software.
o The Budderfly software will inform you that the action was successful. In case the action failed, please repeat
the procedure
- Manual Control: In addition to the Remote control, the Budderfly switches can be controlled manually.
o Tap the top of the rocker to turn ON the connected load.
o Tap the again top of the rocker to turn OFF the connected load.
Battery saving:
The Budderfly RF Multi-Way Switch is designed with battery saving features to minimize battery replacement. Battery life depends
on the sleep time, by default the devices are shipped with sleep time of 5seconds; this value can be changed as desired using
Budderfly software. Noting that the response time of the device for a command coming from the Budderfly software is less than or
equal the sleep time, the device will immediately respond with no delay when the rocker is pressed. If the device is installed
without installing an RF plug or if the plug was powered OFF, the device will scan for new connection in after 1 min, if no
connection is found it will scan again after 2 min then after 4 then 10 minutes and will repeat this after 3 hours, if an immediate
connection scan is required, it can be done by pressing the rocker or by resetting the device.
LED Indicators:
The Budderfly switches are equipped with 2 LED that indicates the different states of the device.
o Color: Green and Red
o State:
Activity
Green LED
Red LED
After Power ON or Reset Solid On for 3 sec Off
Power Cut-Off mode is activated Blinking Off
Searching for connection Solid On for up to 16 sec Off
Top rocker is pressed (Turn On) Blinks once Off
Bottom rocker is pressed (Turn Off) Off Blinks once
Breathing notification
Lights are On
Blinks every sleep time
interval (5 sec by default) Off
Lights are Off
Off
Blinks every sleep time
interval (5 sec by default)
WARNING ʹELECTRICAL SHOCK HAZARD
tŚĞŶƌĞƉůĂĐŝŶŐƚŚĞƵůďƐŵĂŬĞƐƵƌĞƚŽĞŶĂďůĞƚŚĞWŽǁĞƌƵƚ-ŽĨĨŵŽĚĞ/ĨƚŚĞ
power LED does not start blinking, please consult a qualified electrician.