User's Manual

ManualsBrandsBTI Wireless ManualsElectronicsmBSC-CM RUM

Table Of Contents

Document History
Revision History
GENERAL SAFETY PRECAUTIONS
TABLE OF CONTENTS
LIST OF FIGURES
LIST OF TABLES
1 Introduction
- 1.1 System Solution Block Diagram
  - 1.1.1 Host Unit
Figure 1Block Diagram of Host Unit
- 1.1.2 Remote Node
Figure 2 Block Diagram of Remote Node
2 Safety
3 System Overview and Unit Description
- 3.1 System Overview
Figure 3mBSC System Functional Overview
- 3.1.1 Interface with BTS
- 3.1.2 Interface with Cellular Phones
- 3.1.3 Fiber Optic Transport
- 3.1.4 Powering
- 3.1.5 Cooling
- 3.1.6 Fault Detection and Alarm Reporting
- 3.2 Host Unit Description
Figure 4 Host Unit
- 3.2.1 Host Unit Components
  - 3.2.1.1 BIU (BTS Interface Unit)
Figure 5BIU
- 3.2.1.2 FIU (Fiber Interface Unit)
Figure 6FIU
- 3.2.1.3 PSU (Power Supply Unit)
Figure 7 PSU
- 3.2.1.4 RCU (Remote Control Unit)
Figure 8RCU
- 3.2.2 Mounting
- 3.2.3 Fault Detection and Alarm Reporting
- 3.2.4 RF Signal Connections
- 3.2.5 Optical Connections
- 3.2.6 Powering
- 3.2.7 Host Unit Interface
Table 1 Host Unit User Interface
Front Panel
Rear Panel
- 3.3 Remote Node Description
  - 3.3.1 BCM Enclosure
Figure 10Fiber BCM Enclosure Outline
- 3.3.1.1 Primary Components
Figure 11Fiber BCM Interior Layout
- 3.3.1.2 Multiplexer
- 3.3.1.3 Mounting
- 3.3.1.4 RF Connection
- 3.3.1.5 User Interface
Table 3BCM Enclosure User Interface
Figure 12BCM Enclosure User Interface
- 3.3.2 Single-band RUM Enclosure
Table 4 Single-band RUM Enclosure User Interface
Figure 14 Single-band RU Enclosure User Interface
Table 5 Indicator Description
- 3.3.3 RTM
Table 9Fiber RTM Enclosure User Interface
Table 10 Indicator Description
- 3.3.4 RPM
  - 3.3.4.1 Primary Components
4 System Installation
- 4.1 Unpacking and Inspection
- 4.2 Installation Preparation
- 4.3 Host Unit Installation
  - 4.3.1 Rack Mounting
Figure 20 Mounting Brackets for 19” Rack Installation
Figure 21Host Unit-19” Rack Mounting View
- 4.3.2 Cable Connections
  - 4.3.2.1 Grounding
Figure 22Host Unit Grounding Stud
Figure 23 Grounded Host Unit
- 4.3.2.2 Coaxial Cable Connections
Figure 24 BTS QMA Coaxial Cable Connection
- 4.3.2.3 Optical Connections
Figure 26E2000 Fiber Optic Port on Host Unit FIU
- 4.3.2.4 DC Power Connection
Figure 27 48VDC Host Power Connection
- 4.3.2.5 Local OMC Computer Connection
Figure 28IP Connection for local GUI Control
- 4.3.2.6 Modem Connection (optional)
Figure 29Modem Port on RCU (DB9 male)
- 4.4 Remote Node Installation
  - 4.4.1 Cable Connections
Figure 32 Fiber Optic Cable Connection to RTM Enclosure
- 4.4.1.4 AC Power Connection
Figure 33 RPM
- 4.5 Installation Final Inspection
- 4.6 System Test
Figure 36 Flow Chart of System Debugging
5 System Monitoring &Configuration
- 5.1 Accessing EMS Local GUI
Figure 37– EMS Local GUI Login
- 5.2 Navigating the EMS Local GUI
Figure 38- Main Page Expanded Topology
Figure 39- Main Page Summary View
- 5.2.1 Topology Tool Bar
- 5.2.2 Upgrade/Password Functions
- 5.3 Installation & Configuration
  - 5.3.1 Network & Communications
    - 5.3.1.1 Change IP Address of RCU Ethernet port
Figure 40- RCU Component View
- 5.3.1.2 Assign IP Address for Remote EMS Server
- 5.3.1.3 Assign HU Site Name/Number
- 5.3.2 System Installation
  - 5.3.2.1 Verify Component Status
Figure 41- Main Page Equipment Status
- 5.3.2.2 Verify Optical Power Levels
Figure 42- FIU Optical Power Levels
Figure 43- CM Optical Power Levels
- 5.3.2.3 Verify Software Versions
- 5.3.3 Alarms
  - 5.3.3.1 Optical Link Alarms
  - 5.3.3.2 Enable SNMP alarms
- 5.4 System Tuning
- 5.5 Monitoring and Alarms
  - 5.5.1 Operational Status
    - 5.5.1.1 Host Unit
    - 5.5.1.2 Remote Node
  - 5.5.2 System Alarms
Table 16System Alarms
- 5.6 System Upgrade
  - 5.6.1 Verify Software Versions
  - 5.6.2 Upgrade component software
6 Maintenance
- 6.1 Electrostatic Discharge Precautions
- 6.2 Preventative Maintenance
- 6.3 Fault Detection and Alarm Reporting
- 6.4 Troubleshooting Quick Guide
  - 6.4.1 Host Unit Trouble Shooting
Figure 53Host Unit Trouble Shooting
- 6.4.2 Remote Unit Trouble Shooting
Figure 54Remote Unit Trouble Shooting
7 Terms, Acronyms & Abbreviations
IC Radiation Exposure Statement
IC Déclaration sur la radio exposition

MBSC2100E-005-RUCM11

weight of all the equipment and be securely anchored. Installing the Host Unit in a room with sufficient air

circulation is recommended as the maximum ambient temperature for Host Unit is 60°C.

Use the following steps to install the Host Unit in the equipment rack:

1. The Host Unit is built with mounting bracket installed for 19” rack installation.

Figure 20 Mounting Brackets for 19” Rack Installation

2. Position the host unit in the designated mounting space in the rack as shown below.

3. Secure the mounting bracket to the rack using the four mounting screws provided.

Figure 21Host Unit-19” Rack Mounting View

MBSC2100E-005-RUCM11 April 15, 2013

Page 27