User's Manual
Table Of Contents
- Document History
- Revision History
- GENERAL SAFETY PRECAUTIONS
- TABLE OF CONTENTS
- LIST OF FIGURES
- LIST OF TABLES
- Introduction
- Figure 1Block Diagram of Host Unit
- Figure 2 Block Diagram of Remote Node
- Safety
- System Overview and Unit Description
- Figure 3mBSC System Functional Overview
- Figure 4 Host Unit
- Figure 5BIU
- Figure 6FIU
- Figure 7 PSU
- Figure 8RCU
- Table 1 Host Unit User Interface
- Front Panel
- Rear Panel
- Figure 10Fiber BCM Enclosure Outline
- Figure 11Fiber BCM Interior Layout
- Table 3BCM Enclosure User Interface
- Figure 12BCM Enclosure User Interface
- Table 4 Single-band RUM Enclosure User Interface
- Figure 14 Single-band RU Enclosure User Interface
- Table 5 Indicator Description
- Table 9Fiber RTM Enclosure User Interface
- Table 10 Indicator Description
- System Installation
- Figure 20 Mounting Brackets for 19” Rack Installation
- Figure 21Host Unit-19” Rack Mounting View
- Figure 22Host Unit Grounding Stud
- Figure 23 Grounded Host Unit
- Figure 24 BTS QMA Coaxial Cable Connection
- Figure 26E2000 Fiber Optic Port on Host Unit FIU
- Figure 27 48VDC Host Power Connection
- Figure 28IP Connection for local GUI Control
- Figure 29Modem Port on RCU (DB9 male)
- Figure 32 Fiber Optic Cable Connection to RTM Enclosure
- Figure 33 RPM
- Figure 36 Flow Chart of System Debugging
- System Monitoring &Configuration
- Figure 37– EMS Local GUI Login
- Figure 38- Main Page Expanded Topology
- Figure 39- Main Page Summary View
- Figure 40- RCU Component View
- Figure 41- Main Page Equipment Status
- Figure 42- FIU Optical Power Levels
- Figure 43- RTM Optical Power Levels
- Table 16System Alarms
- Maintenance
- Figure 53Host Unit Trouble Shooting
- Figure 54Remote Unit Trouble Shooting
- Terms, Acronyms & Abbreviations
- Packing List
- IC Radiation Exposure Statement
- IC Déclaration sur la radio exposition
mBSC-CM RUM
mBSC-CM December 15, 2015
Page 5
3.1.1 Interface with BTS
The Host Unit is typically installed close to the wireless service provider BTS equipment. In the downlink
path the Host Unit combines RF signals from up to 5bands and feeds the combined signal to a fiber-optic
transceiver for transmission to the interconnected Remote Node(s).In the uplink path the Host Unit converts
a composite multi-band optical signal into independent RF signals for interconnection with the BTS receive
elements.
3.1.2 Interface with Cellular Phones
The mBSC Remote Node interfaces with the cellular phones through the service antennas. In the reverse
path, the Remote Node receives RF signals from cellular phones. In the forward path, the Remote Unit
transmits the RF signals to the cellular phones. A bi-directional antenna is connected to the mBSC Remote
Node to transmit and receive RF signals from the cellular phones.
3.1.3 Fiber Optic Transport
The Host Unit is connected to each Remote Node over a single optical fiber. The optical fibers must be
terminated withE2000/APC connectors for connection with the Host Unit and the Remote Node. For fiber
transmission, and remote node equipment is required, along with an additional optical fiber.
3.1.4 Powering
The Host Unit is powered by -48V DC which is supplied by either the equipment room power distribution
cabinet or an AC/DC converter. The Remote Node is powered by 110/220VAC, 50/60Hz power which is
supplied through a power supply distribution junction box.
3.1.5 Cooling
The Host Unit is cooled through cross-convection without fans.
The Remote Node contains multiple single-band Remote Units, which are cooled through continuous air
flow fans mounted on the top of each singe-band unit. A minimum of 200mm (7.87 inches) of clearance
space must be provided on both the top and the bottom sides of the Remote Node for air flow.
An alarm is provided that indicates if a high temperature condition occurs.
3.1.6 Fault Detection and Alarm Reporting
LED indicators are provided on the front panel of the Host Unit to indicate if the mBSC system is operating
as expected (normal) or if a fault is detected. In addition, normally open and closed alarm contacts (for both
major and minor alarms) are provided at the Host Unit for connection to a customer provided external alarm
system.
The mBSC system also includes a standalone (optional) Element Management System server, which
interconnects with each Host Unit in a multi-system deployment, and is used for system configuration, status
monitoring, and SNMP alarm reporting / management.