User's Manual
Table Of Contents
- Document History
- Revision History
- GENERAL SAFETY PRECAUTIONS
- TABLE OF CONTENTS
- LIST OF FIGURES
- LIST OF TABLES
- Introduction
- Figure 1Block Diagram of Host Unit
- Figure 2 Block Diagram of Remote Node
- Safety
- System Overview and Unit Description
- Figure 3mBSC System Functional Overview
- Figure 4 Host Unit
- Figure 5BIU
- Figure 6FIU
- Figure 7 PSU
- Figure 8RCU
- Table 1 Host Unit User Interface
- Front Panel
- Rear Panel
- Figure 10Fiber BCM Enclosure Outline
- Figure 11Fiber BCM Interior Layout
- Table 3BCM Enclosure User Interface
- Figure 12BCM Enclosure User Interface
- Table 4 Single-band RUM Enclosure User Interface
- Figure 14 Single-band RU Enclosure User Interface
- Table 5 Indicator Description
- Table 9Fiber RTM Enclosure User Interface
- Table 10 Indicator Description
- System Installation
- Figure 20 Mounting Brackets for 19” Rack Installation
- Figure 21Host Unit-19” Rack Mounting View
- Figure 22Host Unit Grounding Stud
- Figure 23 Grounded Host Unit
- Figure 24 BTS QMA Coaxial Cable Connection
- Figure 26E2000 Fiber Optic Port on Host Unit FIU
- Figure 27 48VDC Host Power Connection
- Figure 28IP Connection for local GUI Control
- Figure 29Modem Port on RCU (DB9 male)
- Figure 32 Fiber Optic Cable Connection to RTM Enclosure
- Figure 33 RPM
- Figure 36 Flow Chart of System Debugging
- System Monitoring &Configuration
- Figure 37– EMS Local GUI Login
- Figure 38- Main Page Expanded Topology
- Figure 39- Main Page Summary View
- Figure 40- RCU Component View
- Figure 41- Main Page Equipment Status
- Figure 42- FIU Optical Power Levels
- Figure 43- RTM Optical Power Levels
- Table 16System Alarms
- Maintenance
- Figure 53Host Unit Trouble Shooting
- Figure 54Remote Unit Trouble Shooting
- Terms, Acronyms & Abbreviations
- Packing List
- IC Radiation Exposure Statement
- IC Déclaration sur la radio exposition
mBSC-CM RUM
mBSC-CM December 15, 2015
Page 3
2 Safety
Caution
All the following “Safety Precautions” must be observed during the entire installation and operation of the mBSC system.
1. The mBSC system is designed for maximum safety and reliability when installed, used, and maintained
by trained and qualified technicians in accordance with the procedures and instructions contained in
this manual. To assure the safe operation of your system, always follow the safety and operational
recommendations in this manual.
2. Read and understand all instructions and warnings before handing the mBSC system.
3. Warning: Do not install or operate mBSC system in the presence of flammable gases or fumes.
4. Warning: mBSC system produces high level of RF radiation.
5. Do not operate exposed circuitry or radiating elements with personnel in close proximity to radiating
source.
6. Persons with cardiac pacemakers should avoid exposure to RF radiating elements.
7. Exposing the human eye to high levels of radio-frequency radiation may result in the formation of
cataracts.
8. Warning: We do not provide the antenna; the antenna and other cable set provide by customs. Please
don’t use unauthorized antennas, cables, and/or coupling devices.
9. Warning: To avoid injuries or damage, use care and obtain assistance before lifting the mBSC unit.
10. Warning: mBSC system should be installed only in restricted access areas (dedicated equipment room,
equipment closet, or similarity designated areas) where access is controlled or where access can only
be gained by service personnel with a key or tool. Access to this equipment is restricted to qualified
service personnel only.