Installation Instructions

ManualsBrandsBTI Aqua-Solutions ManualsWater HeatersBTI Aqua-Solutions Digital Instant Hot Water Dispensing Unit

DIGITAL INSTANT HOT WATER DISPENSER INSTALLATION INSTRUCTIONS

ITEM HT4105

PATENT PENDING

REV 4/02/18

Make sure all electrical wiring, connections and water connections conform to local codes.

A standard 110V electrical outlet is required under the sink to power the Dispenser and must supply power CONTINUOUSLY to the

Dispenser.

The cord/plug supplied with the Dispenser must be connected to the power outlet.

The Digital Instant Hot Water Dispenser is a non-pressurized, open vented system with a built-in pressure regulator valve (PRV) that

limits operating pressure to 60 psi.

A Hot & Cold or Hot Only Filtration Faucet must be installed before the Digital Instant Hot Water Dispenser, creating an “open vent”

system, consequently, no pressure is built up inside the Dispenser.

TOOLS REQUIRED PARTS INCLUDED

• Adjustable wrench

• Phillips screwdriver

• 3/8” x 5/16” hot-outlet adapter

• 3/8” x 1/4” cold-inlet adapter

IMPORTANT - WHAT YOU NEED TO KNOW BEFORE YOU START

We are delighted you have chosen the BTI Aqua-Solutions Digital Instant Hot Water Dispenser for use in your home. When used in con-

junction with a Hot & Cold or Hot Only BTI Aqua-Solutions Filtration Faucet, or any other open vented 3-line filtration faucet, this unit will

give you years of hot water whenever you require it.

Please read and follow this step-by-step guide to installation, operation, and care for the Digital Instant Hot Water Dispenser and you will

soon be making your rst cup of coffee, tea, soup, oatmeal or a variety of other items - instantly - and at optimal temperature!

For your safety and a worry-free installation, please read and follow all the instructions, cautions and warnings BEFORE installation or

use of this Digital Instant Hot Water Dispenser. The BTI Aqua-Solutions Digital Instant Hot Water Dispenser is intended only for residen-

tial, not commercial use.

•

Summary of content (8 pages)

PAGE 1
ITEM HT4105 PATENT PENDING DIGITAL INSTANT HOT WATER DISPENSER INSTALLATION INSTRUCTIONS We are delighted you have chosen the BTI Aqua-Solutions Digital Instant Hot Water Dispenser for use in your home. When used in conjunction with a Hot & Cold or Hot Only BTI Aqua-Solutions Filtration Faucet, or any other open vented 3-line filtration faucet, this unit will give you years of hot water whenever you require it.
PAGE 2
ITEM HT4105 SAFETY INSTRUCTIONS - READ BEFORE YOU START These instructions are only intended as a guide. If there is any doubt about installation, please contact a licensed/certified plumber and/or electrician. • ENSURE THE DIGITAL INSTANT HOT WATER DISPENSER IS NOT CONNECTED TO ELECTRIC POWER DURING THE INSTALLATION. • Using an ungrounded or improper connection of the power supply to the product can cause serious injury or death from electrical shock.
PAGE 3
ITEM HT4105 HOW A VENTED FAUCET WORKS Water flows from supply line (A) into the faucet base (B). Water is then diverted inside the faucet into line (C) and into the Digital Instant Hot Water Dispenser (D). F The fresh water displaces hot water in the Dispenser, causing it to flow freely through line (E) to the filtration faucet. Hot water continues straight through the filtration faucet and exits the spout, (F).
PAGE 4
ITEM HT4105 3. BTI AQUA-SOLUTIONS HOT ONLY and HOT & COLD FILTRATION FAUCET W/ DIGITAL INSTANT HOT WATER DISPENSER 3a Hoses are attached to faucet body as shown in diagram. B A A - Blue Label Cold Water-In Hose B - Faucet Stem C - Hot Only Faucet, Hot Handle D - Black Label Pressure Tank Hose E - Hot & Cold Faucet, Cold Handle F - Blue Label Cold Water-In Hose G - Faucet Stem H - Black Label Pressure Tank Hose I - Hot & Cold Faucet, Hot Handle C D F G E I H 3b Drill 1-3/8” hole in countertop.
PAGE 5
ITEM HT4105 4. INSTALLATION IF NOT USING BTI AQUA-SOLUTIONS FILTRATION FAUCET 4a Screw 3/8” x 1/4” cold-inlet adapter onto blue cold-water inlet (A) on top of Dispenser. Screw 3/8” x 5/16” hot-outlet adapter onto red hot-water outlet (B) on top of Dispenser. Make sure larger 5/16” adapter is put onto the red hot-water outlet (B) on top of Dispenser. 4b Connect cold-water line to BLUE cold-water inlet fitting. Connect hot-water line to RED hot-water outlet fitting. Push lines securely into fittings.
PAGE 6
ITEM HT4105 BTI AQUA-SOLUTIONS DIGITAL INSTANT HOT WATER DISPENSER GUIDE TO OPERATION REMEMBER TO ONLY PLUG THE DISPENSER IN AFTER THE UNIT IS COMPLETELY FILLED WITH WATER GETTING TO KNOW YOUR INSTANT HOT WATER DISPENSER RAISE TO NEXT PRESET TEMPERATURE LOWER TEMPERATURE IN 3º INCREMENTS LOWER TO NEXT PRESET TEMPERATURE RAISE TEMPERATURE IN 3º INCREMENTS POWERS ON/OFF, SELECTS VACATION MODE • To power ON/OFF or to select VACATION MODE, simply press and hold center button for 3 seconds.
PAGE 7
ITEM HT4105 HIGH ALTITUDE COOKING Common knowledge tells us that water boils at 212ºF, but that number only represents how water boils at sea level. With each 500 feet of increased elevation, the boiling point of water is lowered by about one degree. That means if you’re cooking at the highest point in South Dakota, you’re going to be boiling at just 198º, and food will take longer to cook because of decreased atmospheric pressure.
PAGE 8
ITEM HT4105 BTI AQUA-SOLUTIONS INSTANT HOT WATER DISPENSER TROUBLESHOOTING GUIDE THE UNIT DOES NOT HEAT WATER The BTI Aqua-Solutions Instant Hot Water Dispenser will take between 8 and 10 minutes (from initial activation) to heat water to the setting specified. If the unit is not heating water, make sure the unit is plugged into a 110V outlet that you have confirmed to be operational. Test the outlet by plugging in another 110V item, such as a light.