User's Manual
Table Of Contents
- What's_in_the_box
- Antenna
- Belt_clip
- Battery
- Installation
- Removal
- Charging_and_battery_maintenance
- Charging
- Battery_Maintenance
- Prolonging_the_life_of_your_battery
- Storage
- Chapter_2._Getting_to_know_your_radio
- The_main_display
- Battery_Level_Indicator
- Status_LED
- Side_key_1_-_CALL_(Broadcast_FM_and_Alar
- Side_key_2_-_MONI_(Monitor_and_Flashligh
- VFO_/_MR_-mode_key
- A_/_B_select_key
- Pound_key
- Keypad_Lock
- Star_key
- Menu_and_function_keys
- Numeric_keypad
- Band_key
- Accessory_jack
- Chapter_3._Basic_Use
- Power_and_volume
- Turning_the_unit_on
- Turning_the_unit_off
- Adjusting_the_volume
- Making_a_call
- Channel_selection
- Frequency_(VFO)_mode
- Channel_(MR)_mode
- Chapter_4._Working_the_menu_system
- Basic_use
- Using_short-cuts
- Chapter_5._Scanning
- Scanning_modes
- Time_operation
- Carrier_operation
- Search_operation
- Tone_Scanning
- Chapter_6._Dual_Watch
- Chapter_7._DTMF
- Chapter_8._Selective_calling
- CTCSS
- DCS
- 1750Hz_Tone-burst
- Chapter_9._Customization
- Display
- Power-on_message
- Chapter_10._Programming
- Manual_programming
- Simplex_channels
- Duplex_channels
- Computer_programming
- Attaching_the_programming_cable
- Radio_to_radio_cloning
- Part_III._How-to_and_setup_guides.
- Appendix_B._Menu_definitions
- 8_BEEP_-_Keypad_Beep
- 6_ABR_-_Display_Illumination_Time
- 25_SFT-D_-_Frequency_Shift_Direction
- 10_R-DCS_-_Receiver_DCS
- 0_SQL_-_Squelch_Level
- RANGE!B8
- General
- Transmitter
- Receiver
- DCS_table
- CTCSS_table
54!
VISIT!BAOFENGTECH.COM!AND!MIKLOR.COM!FOR!DOWNLOADS!AND!HELP!
!
!
!
GMRS-V1!
!
!
!
7. Use!Menu! ! !and! ! !to!configu re!D isplay !A!an d!D isplay!B !(See %Ap pe nd ix%B)!
%!
Power-on!message!
The!power-on!message!can!only!be!se t!via!com puter!link,!see! th e!section!called!“Com puter!
programming”!for!details!on!how !to!set!u p!a!link !with !you r!co m p ute r. !
!
The! following! instruction s! assume! that! you've! already! established! a! link! using! the!BTECH!
software!from!a!computer!runn ing!W indow s,!an d!that!th e !BTECH !softwa re!is!already!installed!
and!running.!
Procedure!10.5.!Setting!th e!p o w e r-on-message!
1. Click!other!in!the!menu!bar;!a!dialogue!box!titled!"Other"!should!have!popped!up.!
2. In!the!box!titled!"Power!On!Message",!th ere!are!two!text!fields !representing !the!two !lines!
on!your!LCD.!Enter!the!desired!text!in!the!fields.!
3. Click!Write!to!write!your!chang es!to !the!rad io.!
!
Make%sure%that%menu%item%38%is%set%to%MSG,%otherwise%your%message%won’t%be%displayed.%
See%Chapter%5%Working%the%menu%system%for%details%on%how%to%nav iga te%the %m en u .%
Some%times%it%takes%the%BTECH%software%more%than%one%try%to%connect%to%your%radio.%If%
you%see%a%dialogue%box%popping%up%stating%that%you%have%a%connection%failure,%close%the%
dialogue%box%and%click%read%or%write%again.%% %