Service manual

Section 9
9-112
9.10.7 Side Tilt Carriage Cylinder (optional)
The optional side tilt carriage cylinder (1, Fig. 9– 75) pro-
vides a way to tilt the carriage attachment from side to
side. The side tilt carriage includes a cylinder that oper-
ates to provide the side tilt motion.
a. Side Tilt Carriage (optional
) Removal
1. Level the boom (place the boom in a horizontal
boom).
2. Tilt the carriage (1, Fig. 9– 75) to fully retract the side
tilt carriage cylinder.
3. Use suitable blocks to support the side tilt carriage
(1) in this position.
4. Engage the park brake switch, place the travel select
lever in NEUTRAL (N) and shut the engine OFF.
5. Unlatch, unlock and open the engine cover. Allow the
hydraulic fluid to cool.
6. Pull the knob on the manually-operated release valve
(Fig. 9– 73) located at the rear of the frame to relieve
pressure in the auxiliary hydraulic system.
Figure 9– 73. Pull the knob on the manually-operated
release valve located at the rear of the frame to relieve
pressure in the auxiliary hydraulic system.
7. Remove all dirt and grease from the side tilt carriage
cylinder and the auxiliary hydraulic lines.
8. Label or otherwise mark the hose assembly (14, Fig.
9– 74).
9. Disconnect and cap all hoses and fittings, etc.
10. Remove the snap rings (11) and cylinder base end
pins (6 and 7) from the mounting plates on the
carriage (1) and pivot base (5).
11. Remove the cylinder using a strap sling and hoist or
other suitable lifting equipment.
12. Wipe up any hydraulic fluid spillage in, on, near and
around the vehicle.
Side Tilt Carriage Legend
WARNING: Hot hydraulic fluid can cause
severe burns. Wait for hydraulic fluid to cool
before servicing any hydraulic component.
WARNING: Escaping hydraulic fluid under
pressure can penetrate the skin, causing seri-
ous injury. Relieve hydraulic pressure before
servicing any hydraulic component.
OS0360
Manually-operated
Release Valve
(for OPTIONAL
Auxiliary Hydraulics)
Model 3606 • Origin 10/99
1. Carriage, Side Tilt
2. Pad, Wear
3. HHCS, 5/16-18 x 1-1/4”
4. Nut, Hex Lock 5/16-18
5. Base, Pivot
6. Pin, Cylinder. Base
7. Pin, Cylinder. Rod
8. Spacer
9. Bushing, Self Align
10. Ring, Snap
11. Ring, Snap
12. Connector, Straight SAE 6-6P - male
JIC 37° x male str. thd. O-ring
13. Tie Wrap
14. Hose Assembly
15. Connector, Straight, SAE 6-8 - male
JIC 37° x male str. thd. O-ring
16. Quick Disconnect, Male,
SAE 8-8ORB - female internal
(Includes Item 17)
17. Seal, Nose (Not Shown)
18. Quick Disconnect, Female,
SAE 8-8ORB - female internal
(Includes Items 19 through 21)
19. Seal, Nose (Not Shown)
20. Seal, Large, Coupler Body
(Not Shown)
21. Back-up Ring for Large Seal
(Not Shown)
22. Plug, Pipe Hex Skt 1/8” NPT
23. Cap, Dust
24. Plug, Dust
25. Molding
26. Pin, Pivot
27. Collar, Pin Locking
28. HHCS, 3/8-16 x 2-3/4”
29. Locknut, 3/8-16 ESNA
30. Shaft, Fork Pivot
31. Hub, Lock
32. HHCS, 5/8-11 x 4”
33. Nut, Hex Lock 5/8-11
34. Fork, Pallet 48” x 4” x 2”
(4,000 lb Rating)
Fork, Lumber (Not Shown)
Fork, Blocking (Not Shown)
35. Washer, Flat Heavy
36. Shim
37. Decal, Capacity Chart
38. Plate, Capacity