BT_DELTA_complete_manual.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 2 * CONTENT S* 01. CONTENTS D 02.SAFETY RULES / FOREWOR JUSTMENT INFORMATION 03. BT DELTA DISASSEMBLY/AD CYLINDER INSTALLATION / 04. BARREL INSTALLATION / AIR PAINTBALLS DER INSTALLATION / LOADING VELOCITY ADJUSTMENT / LOA / OVING AIR SUPPLY / CLEANING 05. STORAGE / UNLOADING / REM ING DISASSEMBLY & FIELD STRIPP IPPING CONTINUED 06. DISASSEMBLY & FIELD STR & TRANSPORTATION 07. REASSEMBLY / STORAGE ORSE 08. S.W.A.T. / BANSHEE / IRONH 09. PARTS LIST 10.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 3 * READ OWNERS MANUAL Rules of Safe Marker Handling BEFORE USING.* BT Paintball Designs, Inc. Model BT DeltaTM No part of this docume nt may be copied or rep 1. Treat every marker as if it were loaded. roduced without the pri consent of BT Paintba or written ll Designs, Inc. . marker ll paintba a of barrel the 2. Never look down 3. Keep your finger off the trigger until ready to shoot. Congratulations on yo ur selection of the BT 4.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 4 B BT DELTA BT DELTA Disassembly Removing the Rip Clip™ or standard side feed neck 1) Turn both locking screws counter clockwise until they stop (Figure 1). 2) Gently pull then tilt the Rip-Clip away from the body and remove. Note: The Locking screws are spring loaded. Magazine Adjustment Removing Barrel from the Complete Barrel Assembly 1) Remove the barrel assembly from marker.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 5 BT PAINTBALL DESIGNS NOTE: Eye protective devices designed specifically for paintball use must be worn by the operator and anyone within range. Read this entire manual before loading, attaching a propellant source or in any way attempting to operate the BT DeltaTM. Barrel Installation Velocity Adjustment Loader Installation 1. Make sure marker is degassed, hopper removed, no paintballs in the feed port or breech and the safety is set to “safe”. 2.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 6 BT PAINTBALL DESIGNS Disassembly and Field Stripping Proper Storage of the Marker When you are finished using the BT Delta™ it is important that you prepare the marker for storage. This will not only serve to increase the life of the marker, but will assure opti- /!\ WARNING: Any assembly/ disassembly of any paintball marker should be performed by a qualified service technician. mum performance on your next outing. Unloading 1.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 7 BATTLE TESTED Rear Notch Sight Removal/Relocation The rear notch sight may be removed or may be relocated along the upper picatinny rail as needed. To remove or adjust location: Note: If relocating, make sure marker is pointed in a safe direction, barrel blocking device is installed and safety is set to safe. 1. Using a 1/8" hex wrench loosen the rear sight retaining screw. 2. Slide rear sight to preferred location or remove if so desired. 3.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 8 The S.W.A.T.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 9 Reassembly S.W.A.T. 06 01 To reassemble the marker, reverse the Disassembly instructions starting with the barrel adapter, ball retainer and bolt removal. While reassembling the marker, you should oil all O-rings and sliding parts. All parts and o-rings returned to the marker should be free of debris and visual nicks and scratches which can alter the performance of the marker.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 10 TM BT-4 MARKER SERIES Parts List ITEM NO. QTY.
BT_DELTA_complete_manual.
BT_DELTA_complete_manual.qxd 9/7/07 7:30 PM Page 12 NTY S, INC. LIMITED WARRA GN SI DE L AL TB IN PA BT is warranty will be anship of this marker. Th warranty servrkm wo r d/o an ial ter ma ginal part due to defect in original purchaser. Such er the replacement of any ori or following the original date of purchase for the nts rra wa . INC LL DESIGNS, INC.
