User manual
Table Of Contents
- Important Safety Instructions 2
- 1.0 Primary Checks
- 2.0 Installation
- 3.0 Warranty Information
- 4.0 Introduction
- 5.0 Features
- b: DATA Indicator
- a: Power Indicator
- c: IQ Interface Indicator
- d: Input Gate Status Display
- e: Digital Display
- f: Selector Buttons
- g: RECALL Button
- h: IR Sensor
- i: RS232 connector
- 7.0 Rear panel
- A: Audio Inputs
- B: Audio Outputs
- C: CobraNet® Connectors
- E: RS232 Serial Port
- D: IQ Loop Connectors
- F: Control Port
- G: Mains Power Inlet
- Using the PS-8810
- 8.0 Quick Install Procedure
- Hardware Installation & Connections
- Connecting to a Host Computer
- RS232 Computer Connection
- Set the Baud Rate
- Comms Problems
- Connecting the IQ Loop
- Set the IQ Address
- PS-8810 as a single loop IQ Interface
- PS-8810 in an IQ Loop system
- IQ Component Connections
- IQ Loop Wiring
- Audio Wiring
- About the Audio Inputs
- Suggested Audio Input Gain Control Settings
- Balanced Input Wiring
- Unbalanced Input Wiring
- About the Audio Outputs
- Balanced Output Wiring
- Unbalanced Output Wiring
- CobraNet® Connections
- Control Port Connections
- Modem Connection
- PC Requirements
- System Overview
- Presets and Scenes
- IQ Win Overview
- Processing Functions
- Output Level Meters
- Output Dynamic Cut/Boost Meters
- Input Level Meters
- Input Dynamic Cut/Boost Meters
- Preset Information
- Status Window
- CPU Utilisation
- DSP
- General
- Real Time Clock
- Front Panel Control Lock Out
- Data
- Interface
- LED Display Mode
- Front Panel Access
- User Labels
- Firmware Information
- Signal Path
- Input Selector
- Input Meter
- Input Select Switch
- Input Processing Selection
- Input Signal Fader, Muter, and Inverter
- Output Overview
- Inputs Window Link
- Input/Output Matrix Link
- Input Filters
- Type
- Frequency
- Gain
- Band EQ
- Shape
- Post-Processing Filters
- Input Delay
- Hardware Delays
- Input Gate
- Enable Gate
- Depth
- Static Threshold
- Hysteresis
- Signal Delay
- Attack Time
- Hold Time
- Release Time
- Side-chain Filter
- Auto-Leveler
- On/Off
- Target Level
- Max Gain
- Idle Gain
- Open to...
- Threshold
- Attack Time
- Release Time
- Input Compressor
- On/Off
- Compression Ratio
- Threshold
- Soft Knee (Width)
- Attack Time
- Release Time
- Side-chain Filter
- Priority Ducking
- Automixer
- Automixing Group Controls
- Priority Mix Enable
- Max Number of Open Mics
- Highest Open Mic Priority Indicator
- Total Number of Open Mics Indicator
- NOM Attenuation
- Adaptive Gating
- Enable
- Mode
- Step Size
- Enable
- Ambient Level Meter
- Group Gate Threshold Ambient Offset
- Ambience Weighting
- Automix Matrix
- Automixing Individual Controls
- Priority
- Depth of Cut
- Attack Time
- Release Time
- Solo/Mute
- Input/Output Matrix
- Output Path
- Output Section
- Output Delay
- Output Filters
- Ambient Leveler
- On/Off
- Sense Input
- Sense Threshold
- Program Level Dependent Mode
- Expansion Ratio
- Max Added Gain
- Attack Time
- Release Time
- Program Level Threshold
- Sense Delay
- Output Limiter
- On/Off
- Threshold
- Attack Time
- Release Time
- Output Select
- 12.0 Presets
- Preset Segue
- Scenes
- Scene Editor
- Events Scheduler
- One Time Events
- Periodic Events
- Schedule
- Explanation
- 15.0 CobraNet®
- Setup
- System Name
- System Description
- System Location
- System Contact
- Firmware Version
- MAC Address
- IP Address
- Conductor
- Status indicators
- Input
- Output
- External Control
- 16.0 Infrared Remote Control
- IR Code Editor
- Infrared Remote Control
- PS8810 IR Code Format
- 17.0 Control Port
- Digital Inputs
- Set Object(s)
- Room Combine
- Bump Object(s)
- Bump Object(s) Continuously
- Recall Preset
- Recall Scene
- Digital Outputs
- Analogue Inputs (AIN 1-8)
- Analogue Outputs
- Reference Section
- 18.0 Technical Information
- Audio
- Input Section
- DSP Processing Section
- Output Section
- 19.0 Block Diagram
- 20.0 Specifications
- 21.0 User Notes
- Untitled
- 80 -
PS-8810
DIGITAL SIGNAL PROCESSOR
The Output Limiter function provides a means of directly
monitoring and controlling peak output level. It is especially
valuable for the protection of amplifiers, loudspeakers and other
audio equipment. The Output Limiter operates similar to a
compressor with an infinite compression ratio, preventing the
output level from exceeding the specified Threshold.
Four parameters control this feature:
On/Off
Turns this feature on or off
Threshold
Used to set the peak signal level above which compression
occurs.
Control range is from -80 to +20dB in 0.5dB steps
Attack Time
Sets the time required for the Limiter to decrease its gain by
20dB.
Control range is from 1 to 100 milliseconds in 1 millisecond
steps
Release Time
Determines how long it takes for the gain to return to normal
when the level drops below the Threshold.
Control range is from 10 milliseconds to 10 seconds in 10
millisecond steps
Processing Functions Output Limiter
b
c
d
e
1
2
3
4
Output
Limiter