User manual
Table Of Contents
- Important Safety Instructions 2
- 1.0 Primary Checks
- 2.0 Installation
- 3.0 Warranty Information
- 4.0 Introduction
- 5.0 Features
- b: DATA Indicator
- a: Power Indicator
- c: IQ Interface Indicator
- d: Input Gate Status Display
- e: Digital Display
- f: Selector Buttons
- g: RECALL Button
- h: IR Sensor
- i: RS232 connector
- 7.0 Rear panel
- A: Audio Inputs
- B: Audio Outputs
- C: CobraNet® Connectors
- E: RS232 Serial Port
- D: IQ Loop Connectors
- F: Control Port
- G: Mains Power Inlet
- Using the PS-8810
- 8.0 Quick Install Procedure
- Hardware Installation & Connections
- Connecting to a Host Computer
- RS232 Computer Connection
- Set the Baud Rate
- Comms Problems
- Connecting the IQ Loop
- Set the IQ Address
- PS-8810 as a single loop IQ Interface
- PS-8810 in an IQ Loop system
- IQ Component Connections
- IQ Loop Wiring
- Audio Wiring
- About the Audio Inputs
- Suggested Audio Input Gain Control Settings
- Balanced Input Wiring
- Unbalanced Input Wiring
- About the Audio Outputs
- Balanced Output Wiring
- Unbalanced Output Wiring
- CobraNet® Connections
- Control Port Connections
- Modem Connection
- PC Requirements
- System Overview
- Presets and Scenes
- IQ Win Overview
- Processing Functions
- Output Level Meters
- Output Dynamic Cut/Boost Meters
- Input Level Meters
- Input Dynamic Cut/Boost Meters
- Preset Information
- Status Window
- CPU Utilisation
- DSP
- General
- Real Time Clock
- Front Panel Control Lock Out
- Data
- Interface
- LED Display Mode
- Front Panel Access
- User Labels
- Firmware Information
- Signal Path
- Input Selector
- Input Meter
- Input Select Switch
- Input Processing Selection
- Input Signal Fader, Muter, and Inverter
- Output Overview
- Inputs Window Link
- Input/Output Matrix Link
- Input Filters
- Type
- Frequency
- Gain
- Band EQ
- Shape
- Post-Processing Filters
- Input Delay
- Hardware Delays
- Input Gate
- Enable Gate
- Depth
- Static Threshold
- Hysteresis
- Signal Delay
- Attack Time
- Hold Time
- Release Time
- Side-chain Filter
- Auto-Leveler
- On/Off
- Target Level
- Max Gain
- Idle Gain
- Open to...
- Threshold
- Attack Time
- Release Time
- Input Compressor
- On/Off
- Compression Ratio
- Threshold
- Soft Knee (Width)
- Attack Time
- Release Time
- Side-chain Filter
- Priority Ducking
- Automixer
- Automixing Group Controls
- Priority Mix Enable
- Max Number of Open Mics
- Highest Open Mic Priority Indicator
- Total Number of Open Mics Indicator
- NOM Attenuation
- Adaptive Gating
- Enable
- Mode
- Step Size
- Enable
- Ambient Level Meter
- Group Gate Threshold Ambient Offset
- Ambience Weighting
- Automix Matrix
- Automixing Individual Controls
- Priority
- Depth of Cut
- Attack Time
- Release Time
- Solo/Mute
- Input/Output Matrix
- Output Path
- Output Section
- Output Delay
- Output Filters
- Ambient Leveler
- On/Off
- Sense Input
- Sense Threshold
- Program Level Dependent Mode
- Expansion Ratio
- Max Added Gain
- Attack Time
- Release Time
- Program Level Threshold
- Sense Delay
- Output Limiter
- On/Off
- Threshold
- Attack Time
- Release Time
- Output Select
- 12.0 Presets
- Preset Segue
- Scenes
- Scene Editor
- Events Scheduler
- One Time Events
- Periodic Events
- Schedule
- Explanation
- 15.0 CobraNet®
- Setup
- System Name
- System Description
- System Location
- System Contact
- Firmware Version
- MAC Address
- IP Address
- Conductor
- Status indicators
- Input
- Output
- External Control
- 16.0 Infrared Remote Control
- IR Code Editor
- Infrared Remote Control
- PS8810 IR Code Format
- 17.0 Control Port
- Digital Inputs
- Set Object(s)
- Room Combine
- Bump Object(s)
- Bump Object(s) Continuously
- Recall Preset
- Recall Scene
- Digital Outputs
- Analogue Inputs (AIN 1-8)
- Analogue Outputs
- Reference Section
- 18.0 Technical Information
- Audio
- Input Section
- DSP Processing Section
- Output Section
- 19.0 Block Diagram
- 20.0 Specifications
- 21.0 User Notes
- Untitled
- 76 -
PS-8810
DIGITAL SIGNAL PROCESSOR
This panel is either accessed by clicking on one of the numbers
written in the 24x10 area or by clicking on the Output fader/mute/
polarity icon at the end of the Output processing section.
In addition to the output of each of the sixteen Input Processing
Sections, the eight CobraNet Inputs are fed to the Matrix Mixer,
providing a 24 Input by 10 Output fully independent crosspoint
mix as controlled by the Input/Output Matrix. Each of the ten
Output Processing Sections has independent fader control of all of
the inputs to the selected output, i.e. a 24:1 mixer, as shown above.
The Mix Mode drop down box is used for selecting exclusive
assignments between a particular input and output. This function
is repeated with the Single Input Mix Mode Buttons or the routing
can be reassigned to the 24:1 mixer.
The selected output channel displays the status of the Output
Processing Section objects and their parameters can be accessed
by clicking on these icons. There is also a button to quickly access
the Input/Output Matrix for further routing options.
Processing Functions Output Path
Output Path