User manual
Table Of Contents
- Important Safety Instructions 2
- 1.0 Primary Checks
- 2.0 Installation
- 3.0 Warranty Information
- 4.0 Introduction
- 5.0 Features
- b: DATA Indicator
- a: Power Indicator
- c: IQ Interface Indicator
- d: Input Gate Status Display
- e: Digital Display
- f: Selector Buttons
- g: RECALL Button
- h: IR Sensor
- i: RS232 connector
- 7.0 Rear panel
- A: Audio Inputs
- B: Audio Outputs
- C: CobraNet® Connectors
- E: RS232 Serial Port
- D: IQ Loop Connectors
- F: Control Port
- G: Mains Power Inlet
- Using the PS-8810
- 8.0 Quick Install Procedure
- Hardware Installation & Connections
- Connecting to a Host Computer
- RS232 Computer Connection
- Set the Baud Rate
- Comms Problems
- Connecting the IQ Loop
- Set the IQ Address
- PS-8810 as a single loop IQ Interface
- PS-8810 in an IQ Loop system
- IQ Component Connections
- IQ Loop Wiring
- Audio Wiring
- About the Audio Inputs
- Suggested Audio Input Gain Control Settings
- Balanced Input Wiring
- Unbalanced Input Wiring
- About the Audio Outputs
- Balanced Output Wiring
- Unbalanced Output Wiring
- CobraNet® Connections
- Control Port Connections
- Modem Connection
- PC Requirements
- System Overview
- Presets and Scenes
- IQ Win Overview
- Processing Functions
- Output Level Meters
- Output Dynamic Cut/Boost Meters
- Input Level Meters
- Input Dynamic Cut/Boost Meters
- Preset Information
- Status Window
- CPU Utilisation
- DSP
- General
- Real Time Clock
- Front Panel Control Lock Out
- Data
- Interface
- LED Display Mode
- Front Panel Access
- User Labels
- Firmware Information
- Signal Path
- Input Selector
- Input Meter
- Input Select Switch
- Input Processing Selection
- Input Signal Fader, Muter, and Inverter
- Output Overview
- Inputs Window Link
- Input/Output Matrix Link
- Input Filters
- Type
- Frequency
- Gain
- Band EQ
- Shape
- Post-Processing Filters
- Input Delay
- Hardware Delays
- Input Gate
- Enable Gate
- Depth
- Static Threshold
- Hysteresis
- Signal Delay
- Attack Time
- Hold Time
- Release Time
- Side-chain Filter
- Auto-Leveler
- On/Off
- Target Level
- Max Gain
- Idle Gain
- Open to...
- Threshold
- Attack Time
- Release Time
- Input Compressor
- On/Off
- Compression Ratio
- Threshold
- Soft Knee (Width)
- Attack Time
- Release Time
- Side-chain Filter
- Priority Ducking
- Automixer
- Automixing Group Controls
- Priority Mix Enable
- Max Number of Open Mics
- Highest Open Mic Priority Indicator
- Total Number of Open Mics Indicator
- NOM Attenuation
- Adaptive Gating
- Enable
- Mode
- Step Size
- Enable
- Ambient Level Meter
- Group Gate Threshold Ambient Offset
- Ambience Weighting
- Automix Matrix
- Automixing Individual Controls
- Priority
- Depth of Cut
- Attack Time
- Release Time
- Solo/Mute
- Input/Output Matrix
- Output Path
- Output Section
- Output Delay
- Output Filters
- Ambient Leveler
- On/Off
- Sense Input
- Sense Threshold
- Program Level Dependent Mode
- Expansion Ratio
- Max Added Gain
- Attack Time
- Release Time
- Program Level Threshold
- Sense Delay
- Output Limiter
- On/Off
- Threshold
- Attack Time
- Release Time
- Output Select
- 12.0 Presets
- Preset Segue
- Scenes
- Scene Editor
- Events Scheduler
- One Time Events
- Periodic Events
- Schedule
- Explanation
- 15.0 CobraNet®
- Setup
- System Name
- System Description
- System Location
- System Contact
- Firmware Version
- MAC Address
- IP Address
- Conductor
- Status indicators
- Input
- Output
- External Control
- 16.0 Infrared Remote Control
- IR Code Editor
- Infrared Remote Control
- PS8810 IR Code Format
- 17.0 Control Port
- Digital Inputs
- Set Object(s)
- Room Combine
- Bump Object(s)
- Bump Object(s) Continuously
- Recall Preset
- Recall Scene
- Digital Outputs
- Analogue Inputs (AIN 1-8)
- Analogue Outputs
- Reference Section
- 18.0 Technical Information
- Audio
- Input Section
- DSP Processing Section
- Output Section
- 19.0 Block Diagram
- 20.0 Specifications
- 21.0 User Notes
- Untitled
- 4 -
PS-8810
DIGITAL SIGNAL PROCESSOR
Contents
Important Safety Instructions....................................................................... 2
1.0 Primary Checks ...................................................................................... 9
2.0 Installation ............................................................................................... 9
3.0 Warranty Information ...........................................................................10
4.0 Introduction ...........................................................................................13
5.0 Features .................................................................................................15
Controls, Connectors & Indicators
6.0 Front Panel .............................................................................................16
b: DATA Indicator ................................................................................................................ 17
a: Power Indicator ..............................................................................................................17
c: IQ Interface Indicator .................................................................................................... 17
d: Input Gate Status Display .............................................................................................. 17
e: Digital Display .................................................................................................................. 17
f: Selector Buttons ............................................................................................................... 18
g: RECALL Button ................................................................................................................. 18
h: IR Sensor ........................................................................................................................... 18
i: RS232 connector ..............................................................................................................18
7.0 Rear panel.............................................................................................19
A: Audio Inputs .................................................................................................................... 19
B: Audio Outputs ................................................................................................................. 19
C: CobraNet® Connectors ............................................................................................... 20
E: RS232 Serial Port ............................................................................................................... 20
D: IQ Loop Connectors ...................................................................................................... 20
F: Control Port ...................................................................................................................... 21
G: Mains Power Inlet ........................................................................................................... 21
Using the PS-8810
8.0 Quick Install Procedure .......................................................................23
9.0 Hardware Installation & Connections ................................................25
Connecting to a Host Computer .................................................................................... 26
RS232 Computer Connection ........................................................................................... 26
Set the Baud Rate ...............................................................................................................27
Comms Problems ................................................................................................................ 28
Connecting the IQ Loop.................................................................................................... 29
Set the IQ Address ..............................................................................................................29
PS-8810 as a single loop IQ Interface ............................................................................... 29
PS-8810 in an IQ Loop system ............................................................................................ 30
IQ Component Connections ............................................................................................ 31
IQ Loop Wiring ..................................................................................................................... 33
Audio Wiring ........................................................................................................................ 34
About the Audio Inputs ...................................................................................................... 34
Suggested Audio Input Gain Control Settings ................................................................ 35