User manual
Table Of Contents
- Important Safety Instructions 2
- 1.0 Primary Checks
- 2.0 Installation
- 3.0 Warranty Information
- 4.0 Introduction
- 5.0 Features
- b: DATA Indicator
- a: Power Indicator
- c: IQ Interface Indicator
- d: Input Gate Status Display
- e: Digital Display
- f: Selector Buttons
- g: RECALL Button
- h: IR Sensor
- i: RS232 connector
- 7.0 Rear panel
- A: Audio Inputs
- B: Audio Outputs
- C: CobraNet® Connectors
- E: RS232 Serial Port
- D: IQ Loop Connectors
- F: Control Port
- G: Mains Power Inlet
- Using the PS-8810
- 8.0 Quick Install Procedure
- Hardware Installation & Connections
- Connecting to a Host Computer
- RS232 Computer Connection
- Set the Baud Rate
- Comms Problems
- Connecting the IQ Loop
- Set the IQ Address
- PS-8810 as a single loop IQ Interface
- PS-8810 in an IQ Loop system
- IQ Component Connections
- IQ Loop Wiring
- Audio Wiring
- About the Audio Inputs
- Suggested Audio Input Gain Control Settings
- Balanced Input Wiring
- Unbalanced Input Wiring
- About the Audio Outputs
- Balanced Output Wiring
- Unbalanced Output Wiring
- CobraNet® Connections
- Control Port Connections
- Modem Connection
- PC Requirements
- System Overview
- Presets and Scenes
- IQ Win Overview
- Processing Functions
- Output Level Meters
- Output Dynamic Cut/Boost Meters
- Input Level Meters
- Input Dynamic Cut/Boost Meters
- Preset Information
- Status Window
- CPU Utilisation
- DSP
- General
- Real Time Clock
- Front Panel Control Lock Out
- Data
- Interface
- LED Display Mode
- Front Panel Access
- User Labels
- Firmware Information
- Signal Path
- Input Selector
- Input Meter
- Input Select Switch
- Input Processing Selection
- Input Signal Fader, Muter, and Inverter
- Output Overview
- Inputs Window Link
- Input/Output Matrix Link
- Input Filters
- Type
- Frequency
- Gain
- Band EQ
- Shape
- Post-Processing Filters
- Input Delay
- Hardware Delays
- Input Gate
- Enable Gate
- Depth
- Static Threshold
- Hysteresis
- Signal Delay
- Attack Time
- Hold Time
- Release Time
- Side-chain Filter
- Auto-Leveler
- On/Off
- Target Level
- Max Gain
- Idle Gain
- Open to...
- Threshold
- Attack Time
- Release Time
- Input Compressor
- On/Off
- Compression Ratio
- Threshold
- Soft Knee (Width)
- Attack Time
- Release Time
- Side-chain Filter
- Priority Ducking
- Automixer
- Automixing Group Controls
- Priority Mix Enable
- Max Number of Open Mics
- Highest Open Mic Priority Indicator
- Total Number of Open Mics Indicator
- NOM Attenuation
- Adaptive Gating
- Enable
- Mode
- Step Size
- Enable
- Ambient Level Meter
- Group Gate Threshold Ambient Offset
- Ambience Weighting
- Automix Matrix
- Automixing Individual Controls
- Priority
- Depth of Cut
- Attack Time
- Release Time
- Solo/Mute
- Input/Output Matrix
- Output Path
- Output Section
- Output Delay
- Output Filters
- Ambient Leveler
- On/Off
- Sense Input
- Sense Threshold
- Program Level Dependent Mode
- Expansion Ratio
- Max Added Gain
- Attack Time
- Release Time
- Program Level Threshold
- Sense Delay
- Output Limiter
- On/Off
- Threshold
- Attack Time
- Release Time
- Output Select
- 12.0 Presets
- Preset Segue
- Scenes
- Scene Editor
- Events Scheduler
- One Time Events
- Periodic Events
- Schedule
- Explanation
- 15.0 CobraNet®
- Setup
- System Name
- System Description
- System Location
- System Contact
- Firmware Version
- MAC Address
- IP Address
- Conductor
- Status indicators
- Input
- Output
- External Control
- 16.0 Infrared Remote Control
- IR Code Editor
- Infrared Remote Control
- PS8810 IR Code Format
- 17.0 Control Port
- Digital Inputs
- Set Object(s)
- Room Combine
- Bump Object(s)
- Bump Object(s) Continuously
- Recall Preset
- Recall Scene
- Digital Outputs
- Analogue Inputs (AIN 1-8)
- Analogue Outputs
- Reference Section
- 18.0 Technical Information
- Audio
- Input Section
- DSP Processing Section
- Output Section
- 19.0 Block Diagram
- 20.0 Specifications
- 21.0 User Notes
- Untitled
- 31 -
PS-8810
DIGITAL SIGNAL PROCESSOR
Three different types of connectors are used for IQ Loop wiring on
IQ components. These include DIN connectors, RJ-45 connectors,
and removable barrier strip plugs. Connection details for these
differing types of connectors are found in the following pages.
The BSS PS-8810 uses RJ-45 connectors that accept plugs like the
one shown below.
RJ-45 Plug
When wiring RJ-45 connectors, it is good practice to follow the
EIA/TIA 568B protocol for RJ-45 connector cable. This protocol
assigns wire colours as follows:
1 white-orange 5 white-blue
2 orange 6 green
3 white-green 7 white-brown
4 blue 8 brown
RJ-45 Pin Numbers
When attaching RJ-45 connectors to cable, be sure to use the
appropriate crimping tool and verify that the connector is
properly seated into the tool or damage will result.
The following examples show how to connect the BSS PS-8810
to other IQ components on the IQ Loop:
RJ-45 Output to Barrier Block Input
Connections IQ Loop
IQ Component
Connections