Instruction Manual

ManualsBrandsbsi ManualsOtherbsi Base Unit

300, 400, 450, 500 and 600 Base Unit Assembly

Components

Ref. No. Item Quantity Ref. No. Item Quantity Ref. No. Item Quantity

Tools Required

1 2

Assembly Instructions

4 5

154085 6

154068 4/6

6154004

151999

152401 4

152418 4

152402 2

5mm

Drill

Spirit Level

G-Clamp

(pair)

Medium Crosshead

Screwdriver

Hammer

Tape Measure

Bradawl

Large Flathead

Screwdriver

150101 10

3.5x12mm

150202 8/12

4x12mm

154082 6

4154027

4x15mm

150201 16

150199

4.5x45mm

152181 2

152162 2

150308 2

150309 2

154047 2

151500 2

152148 2

154082 6

154004

1 2 1 2

1 2

Drawer runner

98mm

1212

Drawer runner

98mm

154085

Start

Locked

Do Not Over Tighten

3.5 x 16mm

Fit as third screw

Front

1 x 'L'; 1 x 'R'

Drawer Runner

Caution: Some pieces of hardware could be hazardous to small children. Keep all these items out of reach and do not leave children unattended in the assembly area.

Please read these instructions carefully before proceeding. Refer to the Guide to Receiving and Installing your Kitchen booklet for further information.

Note: Due to variation in wall conditions no screws are supplied for fixing the units to the wall. If in doubt consult an expert. Assemble the unit on a clean solid work surface.

In the interest of continuing improvements we reserve the right to amend or adjust the specifications without prior notice. Errors and omissions excepted.

These units may be fitted with a drawer system. The drawers are supplied separately. These instructions show the runner positions for the drawer system.

Follow the instructions supplied with the drawers for drawerbox assembly.

Every effort has been made to ensure that this product leaves the factory in perfect condition. In the unlikely event that an item is damaged or incorrect, please contact the customer services department.

Note - Fitting Handles: (1) Decide where you are going to position each handle to maintain symmetry around your kitchen. (2) Measure the handle centres and mark off each door/drawer position. (3) Drill through the door/drawer

using a fine drill (<2.5mm), then drill back from the rear face using a 4.5mm drill. (4) Attach with the fixings provided with your handle.

FM 665131

Important Information - True Handleless Kitchens Installers: See Note Above

Note: If fitting a “True Handleless” kitchen, some

components will differ to those shown in this instruction

and will also be packaged separately. Please refer to your

True Handleless guide to Receiving for further details on

the different components and difference in installation.

Modification required at this stage, see True

Handleless guide for further details.

Modification required at this

stage, see True Handleless

guide for further details.

Summary of content (2 pages)

PAGE 1
300, 400, 450, 500 and 600 Base Unit Assembly TH Note: If fitting a “True Handleless” kitchen, some components will differ to those shown in this instruction and will also be packaged separately. Please refer to your True Handleless guide to Receiving for further details on the different components and difference in installation. Components D E A C A B Important Information - True Handleless Kitchens Installers: See Note Above TH Caution: Some pieces of hardware could be hazardous to small children.
PAGE 2
6 9 10 45mm 7 9 7 8 10 10 2 152401 8 D 150201 4 16 8 9 6 10 150199 125mm 11 10 10 2 150101 10 10 7 8 7 11 2 150202 m 5m 11 11 12 2 154068 mm 45 11 152418 9 150202 4 154047 2 4 140mm Note: Countersunk screw goes into back panel D. 11 9 12 Installation Instructions 14 15 18 15 12 14 2 150202 2 154068 2 151500 12 15 14 82 mm 15 12 17 13 12 15 17 TH C Modification required at this stage, see True Handleless guide for further details.