Instruction manual

77
11 NO PREVIOUS CODE – Status codes are
erased after 72 hours or can be manually erased by putting setup switch SW1-1 in the ON position and jumpering R, W/W1, and Y/Y2 simultaneously until status code #11 is flashed. Run system through a minimum-heat, maximum-heat, or cooling cycle to check system.
12 BLOWER ON AFTER POWER UP –
(115V OR 24V) – Normal operation. Blower runs for 90 seconds, if unit is powered up during a call for heat (R- W/W1 closed) or when (R-W/W1 opens) during the blower on-delay period.
13 LIMIT CIRCUIT LOCKOUT – Lockout
occurs if the limit or flame rollout switch is open longer than 3 minutes or 10 successive limit trips occurred during maximum-heat. Control will auto-reset after 3 hours. See code 33.
14 IGNITION LOCKOUT – System failed to
ignite gas and prove flame in 4 attempts. Control will auto-reset after 3 hours. See status code 34.
21 GAS HEATING LOCKOUT – Turn off
power and wait 5 minutes to retry. Check for: - Stuck closed gas valve relay on control. - Miswire or short to gas valve BLUE wire.
22 ABNORMAL FLAME-PROVING SIGNAL
Flame is proved while gas valve is de- energized. Inducer will run until fault is cleared. Check for: - Stuck open or leaky gas valve.
23 PRESSURE SWITCH DID NOT OPEN –
Check for:
- Obstructed pressure tube. - Pressure switch stuck closed.
24 SECONDARY VOLTAGE FUSE IS OPEN
Check for: - Short circuit in secondary voltage (24V)
wiring including thermostat leads. Disconnect thermostat leads to isolate short circuit.
32 LOW PRESSURE SWITCH DID NOT
CLOSE OR REOPENED – If opens during blower on-delay period, blower will come on for the selected blower off-delay. If opens within 5 minutes after ignition the next heating cycle will be restricted to maximum-heat. Check for: - Proper vent sizing. - Air leak between vestibule and blower
compartment.
- Low inlet gas pressure (if LGPS used). -Restrictedvent. - Disconnected or obstructed pressure
tubing.
- Defective or miswired pressure switches - Excessive wind. If problem persists turn
setup switch SW1-3 ON to boost inducer speed
- Plugged condensate drain. - Water in vent piping, possible sagging
pipe.
33 LIMIT CIRCUIT FAULT – Indicates the
limit or a flame rollout switch is open or the furnace is operating in maximum-heat only mode due to 2 successive limit trips while operating at any rate <
71% of maximum
rate. Blower will run for 4 min. or until open switch remakes whichever is longer. If open longer than 3 min., code changes to lockout #13. If open less than 3 min. status code #33 continues to flash until blower shuts off. Flame rollout switch requires manual reset. Check for: - Loose blower wheel. - Defective switch or connections. - Improper minimum- or maximum-heat
gas input adjustment.
- Improper limit switch or no limit gasket. - Dirty filter or restricted duct system.
34 IGNITION PROVING FAILURE – If flame is
not sensed during the trial for ignition period, the control will repeat the ignition sequence 3 more times before lockout #14 occurs. If flame signal is lost during the blower on-delay period, blower will come on for the selected blower off-delay. Check the following items first before proceeding to the next step. - Gas valve turned off.
- Manual shut-off valve.
- GREEN/YELLOW wire MUST be
connected to furnace sheet metal.
- Flame sensor must not be grounded. To determine whether the problem is in the gas valve, igniter, or flame sensor the system can be operated in component test mode. To check the igniter remove the R thermostat connection from the control, reset power, and put setup switch SW1-6 in the ON position to start the component test. Does the igniter glow orange/white by the end of the 15 second warm-up period?
Unplug igniter harness from control and repeat component test by turning setup switch SW1-6 OFF and then back ON. Check for 115V between pin 3 and NEUTRAL-L2 on the control. Was 115V present for the 15 second period?
Check connections and retry. If current is near typical value (4.0-6.0 nominal) and burners will not stay on, repeat check in max-heat. If burners will still not stay on replace control. If burners operate in max-heat then switch to intermediate-heat, check manifold pressure. If OK, check burner carryover and flame sensor location.
Clean flame sensor with fine steel wool and recheck current. Nominal current is 4.0 to 6.0 microamps. Is current near typical value? Replace electrode. Will main burners ignite and stay on? Replace furnace control. Fixed.
NO YES
YES YES
NO NO
15 BLOWER MOTOR LOCKOUT – Indicates
the blower failed to reach 250 RPM or the blower failed to communicate within 30 seconds after being turned ON in two successive heating cycles. Control will auto-reset after 3 hours. See code 41.
45 CONTROL CIRCUITRY
LOCKOUT Auto-reset after 1 hour lockout due to:
- Flame circuit failure.
- Gas valve relay stuck
open.
- Software check error. Reset power to clear lockout. Replace control if code repeats.
Replace furnace control. Check for continuity in the harness and igniter. Replace defective component.
Reconnect the R thermostat lead and set thermostat to call for heat. Connect voltmeter across gas valve BLUE and GREEN/YELLOW wires. Does gas valve receive 24V? Does gas valve open and allow gas to flow? Do the main burners ignite? Do the main burners stay on?
Allow unit to drop to min-heat, and check manifold pressure. Repeat test to check for intermittent operation. Check that all gas valves are turned on. Replace valve. Check connections. If OK, replace control. Check for: - Inadequate flame carryover
or rough ignition.
- Low inlet gas pressure. - Proper firing rate.
Repeat call for heat and check flame sensor current during trial for ignition period. Is the DC microamps below 0.5?
YES
YES
YES YES
YES NO NO
NO
NO NO NO
43 LOW OR MEDIUM PRESSURE SWITCH
OPEN WHILE MEDIUM OR HIGH PRESSURE SWITCH IS CLOSED - Check for: - Low or Med press. switch stuck open. - Disconnected or obstructed pressure
tubing.
- Improper pressure switch wiring.
- Low inlet gas pressure (if LGPS used). - Plugged condensate drain. - Water in vent piping, possible sagging
pipe.
A11290B
987MA