USERS INFORMATION MANUAL Heating & Cooling Systems MODEL TSTATBBPQ501 5+2 DAY PROGRAMMABLE DIGITAL THERMOSTAT NOTE TO INSTALLER: This manual must be left with the equipment user.
Table Of Contents SAFETY WARNINGS 2 LOCATION OF CONTROLS 3 DISPLAY 4 NORMAL OPERATION Manual Thermostat Operation 5 Time Period Operation 6 7 CLOCK SET PROGRAMMING Setup Overview 8 Program Setup 9 ADVANCED SETUP 16 BATTERY REPLACEMENT 18 WARRANTY 19 Bryant Heating & Cooling Systems Page 1 Patents Pending 4/03
Safety Warnings TSTATBBPQ501 CAUTION Follow Installation Instructions carefully. DISCONNECT POWER TO THE HEATER AIR CONDITIONER BEFORE REMOVING THE OLD THERMOSTAT AND INSTALLING THE NEW THERMOSTAT. WARNING CAUTION The 2 Alkaline “AA” batteries must be replaced at least every 12 months to assure proper operation. The thermostat will display the Low Battery code (fig. 1) on the display of the thermostat when it is time to replace the batteries. If the FIG.
Location of Controls HEAT/COOL INDICATOR 72 Tu AM next I2:00 run 72 SET prog off set UP & DOWN BUTTONS The Heat/Cool indicator will only energize if the thermostat is system powered. MODE SWITCH Heat, Cool or Off FAN SWITCH On or Auto NEXT BUTTON For programming How to Use: The Next button is used to advance from one step to the next in the programming and advanced setup screens of the thermostat (pages 8-16). It is also used to enter the Advanced Setup screens (page 16).
Display 88 AM MTuWThF SaSuHeatCoolPM I2:00 Day Morning Night Evening 88 SET Day of the week. When programming, MTuWThF represents the 5 weekdays, SaSu represent the 2 weekend days. Heat and Cool indicators. In normal operation, Heat or Cool appears, reflecting the mode switch position. Clock Display. Time period indicators. These indicate the part of the program that is currently active, if the program switch is positioned to Run. Desired Set temperature indicator. Current room temperature indicator.
Normal Operation PROGRAM SWITCH 72 Tu Program Switch Heat AM I2:00 72 RUN SET next UP & DOWN BUTTONS run prog off set OFF SET FAN SWITCH On or Auto MODE SWITCH Heat, Cool or Off Manual Operation (program switch OFF) Select heat or cool with the mode switch. Normally leave the fan switched to auto. In fan auto, the fan will turn on only with a heat or cool demand. When Fan On is selected, the fan will run continuously. Adjust the desired set temperature with the Up or Down buttons.
Normal Operation PROGRAM SWITCH 72 Tu Program Switch Heat AM I2:00 72 RUN SET next UP & DOWN BUTTONS run prog off set OFF SET FAN SWITCH On or Auto MODE SWITCH Heat, Cool or Off Programmed Operation (program switch RUN) Select heat or cool with the mode switch. Normally leave the fan switched to auto. In fan auto, the fan will turn on only with a heat or cool demand. When Fan On is selected, the fan will run continuously.
Clock Set Program Slide the program switch to the SET position. RUN OFF SET Setting the time & day are the first 2 steps after sliding the program switch to SET. PM 6:00 Use these buttons to adjust the current time. Pushing and holding the Up or Down buttons will slew the time by 10s of minutes. Press the NEXT button for 5 seconds to enter advanced setup. (Page16) NEXT Su Use these buttons to adjust the current day.
Time Period Programming Overview PROGRAM SWITCH Slide the program switch to the SET position. Program The blinking icon(s) on the display may be Switch RUN changed by pressing the Up or Down buttons. OFF After the blinking icon is changed how you want SET it, press the Next button. The next icon in ‘programming sequence’ will flash. It can be modified with the Up & Down buttons. Continue the steps above until programming is complete.
Time Period Programming Weekday Programming Slide the program switch to the SET position. The 1st 2 steps are clock and day set, see page 7. Program RUN OFF SET MTuWThF AM 6:00 Use these buttons to adjust the start time for the morning time period. Morning NEXT AM MTuWThF Cool 6:00 Use these buttons to adjust the cool setpoint for the morning time period. Morning 78 SET NEXT MTuWThF Heat AM 6:00 Use these buttons to adjust the heat setpoint for the morning time period.
Time Period Programming Weekday Programming AM MTuWThF Cool 8:00 Day 85 SET NEXT MTuWThF Heat AM 8:00 Day 62 SET NEXT MTuWThF PM 6:00 Evening NEXT MTuWThF Cool PM 6:00 Evening NEXT 78 SET Use these buttons to adjust the cool setpoint for the day time period. Use these buttons to adjust the heat setpoint for the day time period. Use these buttons to adjust the start time for the evening time period. Use these buttons to adjust the cool setpoint for the evening time period.
Time Period Programming Weekday Programming MTuWThF Heat PM 6:00 Evening 70 SET NEXT MTuWThF PM I0:00 Night NEXT MTuWThF Cool PM I0:00 Night 82 SET NEXT MTuWThF Heat PM I0:00 Night NEXT 62 SET Use these buttons to adjust the heat setpoint for the evening time period. Use these buttons to adjust the start time for the night time period. Use these buttons to adjust the cool setpoint for the night time period. Use these buttons to adjust the heat setpoint for the night time period.
Time Period Programming Weekend Programming AM SaSu 6:00 Morning NEXT SaSu AM Cool 6:00 Morning 78 SET NEXT SaSu Heat AM 6:00 Morning 70 SET NEXT SaSu AM 8:00 Day NEXT Use these buttons to adjust the start time for the morning time period. Use these buttons to adjust the cool setpoint for the morning time period. Use these buttons to adjust the heat setpoint for the morning time period. Use these buttons to adjust the start time for the day time period.
Time Period Programming Weekend Programming SaSu AM Cool 8:00 Day 85 SET NEXT AM SaSu Heat 8:00 Day 62 SET NEXT SaSu PM 6:00 Evening NEXT SaSu Cool PM 6:00 Evening NEXT 78 SET Use these buttons to adjust the cool setpoint for the day time period. Use these buttons to adjust the heat setpoint for the day time period. Use these buttons to adjust the start time for the evening time period. Use these buttons to adjust the cool setpoint for the evening time period.
Time Period Programming Weekend Programming SaSu Heat PM 6:00 Evening 70 SET NEXT SaSu PM I0:00 Night NEXT SaSu Cool PM I0:00 Night 82 SET NEXT SaSu Heat PM I0:00 Night NEXT 62 SET Use these buttons to adjust the heat setpoint for the evening time period. Use these buttons to adjust the start time for the night time period. Use these buttons to adjust the cool setpoint for the night time period. Use these buttons to adjust the heat setpoint for the night time period.
Time Period Programming After completion of setting the time period programming, you have 2 options: 1) Run the time period program by sliding the Program Switch to the RUN position. Or, 2) Do not run the time period program. The thermostat will operate as a manual heat/cool thermostat. Slide the Program Switch to OFF in this case.
Advanced Setup This is normally done by the installer at initial installation. Enter advanced setup by adjusting the program switch to SET. When the clock is flashing, press NEXT for 5 seconds. Do not release the button until this screen appears. NEXT NEXT NEXT I 6 LI F Use these buttons to adjust the deadband from 1 to 6 degrees. Use these buttons to adjust the cycles/hour from 2 to 6. d=no limit (zoning) d1=d+no compressor lockout.
Battery Replacement To Open The Thermostat The top of the thermostat housing has two (2) screwSCREWDRIVER driver slots to assist when seperating. SLOTS To pull the housing apart, insert a small blade screwdriver into the slot and rotate 90 . This will release the top housing snaps. Repeat the procedure in the other screw driver slot. Separate the housing halves by pulling the top forward until the pins release, and then lift the bottom out.
Battery Replacement REPLACE WITH ALKALINE BATTERIES AT LEAST ONCE EVERY YEAR, OR WHEN THE “LOW BATTERY” ICON APPEARS (pages 2,17). POSITION BATTERIES AS SHOWN HP GAS USE “AA” SIZE ALKALINE BATTERIES ELEC GAS USE “AA” SIZE ALKALINE BATTERIES IF THE THERMOSTAT IS CONNECTED TO 24V POWER, THE BATTERIES MAY STILL BE INSTALLED. INSTALLING THE BATTERIES WHEN SYSTEM POWERED (24VAC) WILL KEEP THE CLOCK RUNNING IN THE EVENT OF LINE POWER INTERRUPTION.
Warranty 5-Year Warranty - This Product is warranted to be free from defects in material and workmanship. If it appears within five years from the date of original installation, whether or not actual use begins on that date, that the product does meet this warranty, a new or remanufactured part, at the manufacturer’s sole option, to replace any defective part will be provided without charge for the part itself; PROVIDED the defective part is returned to the distributor through a qualified servicing dealer.
Programming Worksheet DAY Monday Tuesday Wednesday Thursday Friday see page 8 PERIOD START TIME COOL HEAT Morning Day Evening Night Morning Saturday Sunday Day Evening Night Please be certain to program each time period in chronological order to ensure proper programmed operation of the thermostat. For example, if the Morning Start Time is 6:30am, then the Day Start Time MUST be programmed for any time AFTER the 6:30am Morning Start Time.
