BT65011 & BT65011IND Power Pro 1100 Tile Saw OWNER’S MANUAL WARNING! Read and follow all safety and operating instructions before using this saw.
BT65011 & BT65011IND Power Pro 1100 Tile Saw WARNING For your own safety, read instruction manual before operating saw. 1. Always wear safety goggles when cutting. 2. Use splash hood for every operation for which it can be used. 3. Disconnect saw before cleaning or changing blade. 4. Do not use any cutting blade with openings and grooves. Use only continuous rim blades. 5. Replace damaged blade before operating. 6. Do not expose to rain or use in damp locations.
WARNING! GENERAL SAFETY INSTRUCTIONS FOR TILE SAW READ THIS OWNER’S MANUAL COMPLETELY AND MAKE SURE YOU UNDERSTAND ALL OF IT’S SAFETY GUIDELINES. 1. KEEP GUARDS IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND SPANNERS. Always check to see that keys and adjusting spanners are removed from tool before turning it on. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 4. DO NOT USE IN DANGEROUS ENVIRONMENT.
WARNING! • • • • • • • GENERAL SAFETY INSTRUCTIONS FOR TILE SAW For Your Own Safety Read Instruction Manual Before Operating Saw Wear eye protection. Use blade guard when cutting. Disconnect saw before servicing, when changing cutting wheels, and cleaning. Use tool only with continuous rim cutting wheels free of opening and grooves. Replace damaged blades before operating. Do not expose to rain or use in damp location. Turn off the power before adjusting the angle for mitre cuts.
WARNING! SPECIFIC SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Ensure that the directional arrow marked on the blade corresponds with the rotational direction of the motor. With the saw disconnected from the power supply, rotate the blade by hand to ensure it is free from obstruction. Always keep the blade-securing bore and collars clean. Ensure that the blade-securing bolt is securely tightened. Never try to cut freehand.
ASSEMBLY & SET UP CAUTION! The following is step-by-step installation and operation instruction manual. Please read the information thoroughly prior to using your tile saw. A. Stand Setup 1. The Saw and Stand are ready to use. Simply unfold it as shown below. 2. Place the saw frame on the stand and tighten the stand knobs for safety. (See Diagram 1) You may need to move or remove water tray to easily secure safety knobs to stand frame. Diagram 1 B.
CAUTION! Make sure that the directional arrow on the blade points in the same direction as the arrow marked on the blade guard fixing plate. E. Water Pump Installation Step 1: Make sure the water pump is not cracked or damaged in any way. Step 2: Attach the end of the tube to the pump nipple and L -shaped water flow at the back of blade guard. Step 3: Place the Pump at the location in the water tray that has been designed to secure the pump during use. (See the Diagram 7).
SAW OPERATION CAUTION! 1. Do not adjust the saw without first turning off the motor. Failure to do so may result in serious injury to the operator. 2. Always keep the saw clear. Never put things on rail while cutting. Adjustable Cutting Table Extension The adjustable cutting extension table is for the support of large format tiles. Users could adjust front and side extension to desired dimension. (See Diagram 10) Diagram 12 Motor head height adjustment lever Cutting Tile and Stone WARNING! 1.
Angle / Mitre Cuts WARNING! Diagram 17 The saw is adjustable to three positions (0°, 22.5 °or 45°). Any other angle cut will damage the work table. Step 1: Turn off the power. Step 2: Position the cutting table in its farthest back position and lock with slide tube locking knob. Step 3: Loosen the Angle Adjustable Knob on the Angle Support Arm (See Diagram 18), found at the back of the motor head, to adjust the guide by tilting the head (See Diagram 19) to 22.5° or 45°angles.
Diagram 22 DIAMOND BLADES 1. Use only 250 mm wet continuous rim diamond blade with this saw. 2. Bore size is 16 mm Please choose the right size to fit the inner flange. 3. Do not use wood sawing blade, or other blades not suitable for ceramic, porcelain or stone. Severe body injury or the saw damage may occur. DO & DON'TS For Diamond Blades DO'S: 1. Inspect blades daily for cracks or uneven wear. Discard cracked, chipped or bent blades! 2.
NOTES ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ _______________________________
Made in China Brutus® is a registered trademark of Q.E.P. Co., Inc. Q.E.P. Co., UK Ltd, Everest Road, Lytham St Annes, Lancashire. FY8 3AZ England Tel. +44 (0) 1253 789 180 www.qep.
