MAXUS ® SHOTGUN OWNER’S MANUAL
Important operating instructions for: BROWNING MAXUS® AUTOLOADING SHOTGUNS If you have any questions about your new firearm, this owner’s manual or other Browning products, contact: Browning Customer Service One Browning Place Morgan, UT 84050-9326 Phone: (800) 333-3288 browning.com Please use the space below to record information about your firearm.
C O N T E N T S P A G E State Warning............................................................................................2 WARNING: You are Responsible for Firearms Safety............................2 General Description and Operation......................................................10 Nomenclature..........................................................................................10 Serial Number.........................................................................................
S TAT E WA R N I N G According to state law, California requires that firearm manufacturers, distributors and retailers include conspicuous, specific warnings with firearms sold in that state. Firearms must be handled responsibly and securely stored to prevent access by children and other unauthorized users. California has strict laws pertaining to firearms, and you may be fined or imprisoned if you fail to comply with them. Visit the Web site of the California Attorney General at https://oag.ca.
Please read and understand all of the cautions, warnings, notices, proper handling procedures and instructions outlined in this owner’s manual before using your new firearm. 1 ALWAYS KEEP THE MUZZLE OF YOUR FIREARM POINTED IN A SAFE DIRECTION EVEN THOUGH YOU ARE CERTAIN IT IS UNLOADED. Never point any firearm at anything you do not intend to shoot. Be extremely alert and aware of all persons and property within the range of your ammunition.
3 WHENEVER YOU HANDLE ANY FIREARM, OR HAND IT TO SOMEONE, ALWAYS OPEN THE ACTION IMMEDIATELY AND VISUALLY CHECK THE FIREARM’S CHAMBER TO MAKE CERTAIN THAT THE FIREARM IS COMPLETELY UNLOADED. Make certain the firearm does not inadvertently contain any ammunition. Remember, merely removing the magazine does not mean the chamber is unloaded. Always keep the chamber empty and the “safety” in the on safe position unless shooting is imminent. 4 ALWAYS WEAR EAR AND EYE PROTECTION WHEN SHOOTING.
HUNTING FROM ELEVATED SURFACES SUCH AS TREE STANDS IS DANGEROUS. Doing so may increase the risk of mishandling a firearm. The following rules should always be observed by you and those you hunt with. Always make certain that the stand being used is safe and stable. Always make certain that your firearm is unloaded when it is being taken up and down from the stand. Always make certain that your firearm is not dropped from the stand, or dropped while it is being taken up or down from the stand.
10 BE ALERT TO THE SIGNS OF AMMUNITION MALFUNCTION. IF YOU DETECT AN OFF SOUND OR LIGHT RECOIL WHEN A SHELL IS FIRED, DO NOT LOAD ANOTHER SHELL INTO THE CHAMBER. If your firearm fails to fire, keep the muzzle pointed in a safe direction for a minimum of 30 seconds. Rotate the ejection area of the firearm away from you, carefully open the action and remove the shell from the chamber. If the primer is indented, the defective shell should be disposed of in a way that cannot cause harm.
assume no liability for incidents which occur through the use of shells of nonstandard dimensions or which develop pressures in excess of commercially available ammunition which has been loaded in accordance with standards established by the Sporting Arms and Ammunition Manufacturers’ Institute (SAAMI).
20 BE CERTAIN YOUR FIREARM IS UNLOADED BEFORE CLEANING. Because so many firearm accidents occur when a firearm is being cleaned, special and extreme care should be taken to be sure your firearm is unloaded before disassembly, cleaning and reassembly. Keep ammunition away from the cleaning location. Never test the mechanical function of any firearm with live ammunition. 21 TEACH AND SUPERVISE FIREARMS SAFETY TO ALL MEMBERS OF YOUR FAMILY, ESPECIALLY TO CHILDREN AND NON-SHOOTERS.
25 DO NOT, UNDER ANY CIRCUMSTANCES, ALTER THE TRIGGER, “SAFETY” OR OTHER PARTS OF THE FIRING MECHANISM OF THIS OR ANY OTHER FIREARM EXCEPT AS OTHERWISE DESCRIBED IN THIS MANUAL. We reserve the right to refuse service on firearms that have been altered, added to or substantially changed. Removal of metal from the barrel, or modifications of the firing mechanism and/or operating parts may lead to a refusal of service on such firearms.
FIGURE 1 Bolt Handle Buttstock Receiver “Safety” Recoil Pad Trigger Rib Barrel Front Sight Bead Muzzle Forearm Speed Lock Lever Bolt Release Button G E N E R A L D E S C R I P T I O N A N D O P E R AT I O N The Browning Maxus is a gas-operated, autoloading shotgun capable of quickly firing up to five shells (with the three-shot adaptor removed, using 2¾" loads), one shell at a time, with each successive pull of the trigger.
FIGURE 2 Barrel Gas Bracket Bolt Barrel Extension Piston Sleeve Spring Slide Link Bolt Slide Recoil Pad Bolt Handle Piston Sleeve Gas Piston Magazine Receiver Three-Shot Adaptor Forearm Trigger Group Trigger Group Pins the receiver, above the trigger guard. Record this number in the space provided at the front of this owner's manual for future reference. INITIAL CLEANING PLEASE TAKE NOTE OF THE FOLLOWING INFORMATION BEFORE CLEANING YOUR FIREARM.
CLEANING FIGURE 3 Various exposed metal parts of your new firearm have been coated at the factory with a rust preventative compound. Before assembling your shotgun, clean the anti-rust compound from the inside of the barrel, receiver and the action/chamber areas. A highquality lightweight gun oil is ideal Lightly lubricate the bolt rails inside the receiver. for removing this compound, and for giving your new firearm its first lubrication.
FIGURE 4 FIGURE 5 The “safety” shown in the on safe position. The “safety” shown in the off safe position. DO NOT DEPEND ON THE RED COLOR ALONE TO INDICATE YOUR FIREARM’S SAFETY STATUS. TIME, EXPOSURE TO THE ELEMENTS, AND THE ABRASIVE ACTION OF CLEANING AGENTS CAN ERASE IT. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH. The “safety” can be reversed from right- to left-handed by a qualified gunsmith.
1 Lock the bolt rearward by pulling the operating handle fully to the rear. NEVER ALLOW THE ACTION TO SLAM CLOSED BY PRESSING THE BOLT RELEASE BUTTON WITHOUT THE BARREL INSTALLED. IF THE BOLT IS RELEASED FORWARD WITH THE BARREL REMOVED, THE OPERATING HANDLE WILL STRIKE THE RECEIVER AND CAUSE DAMAGE. FIGURE 6 Press and hold the release button while lifting the Speed Lock lever.
FIGURE 8 FIGURE 9 Slide the gas bracket and gas system components over the magazine tube and the barrel extension into the receiver. Ensure the forearm is secured correctly, with the button flush with the forearm, as shown in the picture on the left. 5 Align the barrel extension with the top of the receiver and place the gas bracket over the magazine tube (Figure 8). The barrel extension should slip solidly into the receiver. Make sure the push rod moves freely in its slot in the receiver.
D I S A S S E M B LY ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. BEFORE STARTING DISASSEMBLY PROCEDURES, OPEN THE ACTION AND VISUALLY INSPECT THE CHAMBER TO BE ABSOLUTELY CERTAIN THE FIREARM IS COMPLETELY UNLOADED. PLACE THE “SAFETY” IN THE ON SAFE POSITION. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH. 1 Lock the bolt rearward by pulling the operating handle fully to the rear.
THE BOLT IS RELEASED FORWARD WITH THE BARREL REMOVED, THE OPERATING HANDLE WILL STRIKE THE RECEIVER, CAUSING DAMAGE. AMMUNITION DISCHARGING FIREARMS IN POORLY VENTILATED AREAS, CLEANING FIREARMS OR HANDLING AMMUNITION MAY RESULT IN EXPOSURE TO LEAD AND OTHER SUBSTANCES KNOWN TO CAUSE BIRTH DEFECTS, REPRODUCTIVE HARM AND OTHER SERIOUS PHYSICAL INJURY. HAVE ADEQUATE VENTILATION AT ALL TIMES. WASH HANDS THOROUGHLY AFTER EXPOSURE. USE ONLY SHELLS OF THE CORRECT GAUGE AND LENGTH.
Your shotgun will misfire (with the chamber appearing to be empty). It is then possible to load the correct gauge shell behind the smaller gauge shell. If the shotgun is then fired, the result will be a so-called “12-16, 12-20, 20-28 or 28-.410 burst” which can cause extensive damage to your shotgun and possible serious injury to you and others.
FIGURE 10 FIGURE 11 Use a key or screwdriver to press in on the three-shot adaptor, then rotate a quarter-turn. Remove the three-shot adaptor. The Maxus is delivered with the magazine three-shot adaptor (plug) installed in the magazine, limiting magazine capacity to two shells in compliance with federal migratory bird regulations.
4 If the barrel is on the shotgun, hold it to prevent it from falling out of the receiver while pointing the magazine tube down to allow the three-shot adaptor (plug) to fall out of the end of the magazine tube. Grasp and remove it (Figure 11, page 19). 5 Reinstall the forearm as explained previously. When the forearm is in place and the Speed Lock lever is fully locked, the release button is flush with the surface of the forearm (Figure 9, page 15).
5 Reinstall the forearm as explained previously. When the forearm is in place and the Speed Lock lever is fully locked, the release button is flush with the surface of the forearm (Figure 9, page 15). FIGURE 12 ALWAYS ENSURE THE FOREARM IS FULLY LOCKED AND THE SPEED LOCK The three-shot adaptor shown secured in the LEVER RELEASE BUTTON IS FLUSH magazine tube. WITH THE SURFACE OF THE FOREARM. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY, DEATH OR DAMAGE TO YOUR FIREARM.
SPEED LOADING FIGURE 13 1 If shooting is imminent, lock the bolt open and insert a shell into the magazine (Figure 13). The shell will be automatically cycled from the magazine to the chamber. KEEP YOUR FINGERS CLEAR OF THE EJECTION PORT WHEN LOADING Insert the shell into the bottom of the receiver and push it fully forward into the magazine. THE SHOTGUN USING THE SPEED LOADING PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN INJURY.
(Figure 13, page 22). Make certain the rim of the shell engages the shell stop and is held fully inside the magazine tube. It will make an audible click when fully inserted. FIGURE 14 4 If desired, continue loading the magazine until it is full. LOADING THE CHAMBER M A N U A L LY F R O M THE MAGAZINE Insert a shell through the ejection port into the breech.
3 Press the bolt release button to deliver the shell into the chamber. KEEP YOUR FINGERS CLEAR OF THE EJECTION PORT WHENEVER CLOSING THE ACTION WITH THE BOLT RELEASE BUTTON. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN INJURY. THE SHOTGUN IS NOW READY TO FIRE BY SIMPLY MOVING THE “SAFETY” TO THE OFF SAFE POSITION AND PULLING THE TRIGGER. 4 With a shell in the chamber, you may load the magazine to full capacity.
fired, the breech of the shotgun remains open, with the bolt locked to the rear. This allows convenient and fast reloading. If you are done shooting, leave the bolt locked to the rear, with the breech in the open position so that you may visually inspect the chamber, bore, carrier and magazine to be sure they contain no shells. AFTER FIRING, OR WHEN SHOOTING IS NO LONGER IMMINENT, IMMEDIATELY PLACE THE “SAFETY” IN THE ON SAFE POSITION.
the right side of the loading port (visually to the left side when looking down into the loading port). 3 Push inward on the shell stop with your index finger (Figure 15) to release a shell from the magazine. As the shell stop is pressed in, the shell will be forced out of the magazine under spring pressure. Catch the shell in your hand as it comes out. FIGURE 15 Push inward on the shell stop to unload the magazine. 4 Press the stop again to release the next shell.
FIGURE 16 FIGURE 17 Pull the Magazine Cut-Off rearward to block the magazine. Push the Magazine Cut-Off forward to unblock the magazine. and ejected. Visually inspect the chamber, feed mechanism and magazine to assure there are no shells remaining. M A G A Z I N E C U T- O F F WHEN UNLOADING YOUR SHOTGUN ALWAYS PLACE THE “SAFETY” IN THE ON SAFE POSITION. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION AND YOUR FINGERS AWAY FROM THE TRIGGER.
THE SHOTGUN IS NOW READY TO FIRE BY SIMPLY MOVING THE “SAFETY” TO THE OFF SAFE POSITION AND PULLING THE TRIGGER. 4 The shotgun may now be fired as explained on pages 24-25 and will fire only the shell in the chamber. 5 To disengage the Magazine Cut-Off, place the "safety" in the on safe position, then push the Magazine Cut-Off lever fully forward (Figure 17, page 27). If the action is open, shells will immediately feed from the magazine.
FAILURE TO FOLLOW THIS INFORMATION COULD RESULT IN DAMAGE TO YOUR SHOTGUN OR POSSIBLE INJURY. USE ONLY THE INVECTOR CHOKE TUBE WRENCH SUPPLIED WITH YOUR SHOTGUN TO INSTALL AND REMOVE INVECTOR CHOKE TUBES. USING ANY OTHER WRENCH MAY DAMAGE THE THREADS IN THE BARREL. Current production Maxus shotgun barrels are threaded to accept the Invector-Plus choke system. Browning Standard Invector, Invector-Plus and Invector-DS tubes are not interchangeable.
FIGURE 19 * ONE NOTCH THREE NOTCHES FIVE NOTCHES TWO NOTCHES FOUR NOTCHES NO NOTCHES RIM NOTCHES PAT T E R N W I T H LEAD SHOT PAT T E R N W I T H STEEL SHOT EXTENDED** X-FULL TURKEY ** I FULL * II I M P. M O D I F I E D FULL1 III MODIFIED FULL1 IIII I M P. C Y L I N D E R MODIFIED IIIII SKEET I M P. C Y L I N D E R NO NOTCHES CYLINDER CYLINDER Not for use with steel shot. Using an over-tight choke constriction with steel shot will result in an ineffective “blown” pattern.
Replacement and additional tubes and wrenches are available from your Browning dealer, or by contacting our Consumer Department. See “Service or Repair” on page 52 for contact information. FIGURE 20 CHOKE TUBE SELECTION To help you choose the correct choke tube for your hunting or shooting situation, all Browning Invector Use the choke tube wrench to change choke tubes are inscribed on the choke tubes. side with the patterns they produce with both lead and steel shot.
C H O K E T U B E I N S TA L L AT I O N 1 Place the “safety” in the on safe position. Always make sure the shotgun is completely unloaded. Always keep the muzzle pointed in a safe direction. 2 Before installing a tube, check the internal choke tube threads in the muzzle, as well as the threads on the choke tube to be sure they are clean. Lightly oil the threads with a high-quality, lightweight gun oil.
FIGURE 21 FIGURE 22 Insert a screwdriver into the holes in the recoil pad. Install or remove stock spacers to achieve correct length of pull. SHOTGUN IS COMPLETELY UNLOADED. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. I N S TA L L I N G A S PA C E R 1 Use a #2 cross tip or Phillips screwdriver to remove the recoil pad at the end of the buttstock (Figure 21).
4 Attach the recoil pad to the stock using the screwdriver. Turn the screws clockwise to tighten. Do not overtighten the screws. A D J U S T I N G C A S T A N D D R O P AT C O M B BEFORE PERFORMING ADJUSTMENT PROCEDURES, PLACE THE “SAFETY” IN THE ON SAFE POSITION. OPEN THE ACTION AND MAKE CERTAIN YOUR SHOTGUN IS COMPLETELY UNLOADED. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.
Cast is the offset of the buttstock from the longitudinal center line of the firearm. Some right-handed shooters like the stock to angle away (cast off) from their face, making their line of sight more directly in line with the barrel. Angling the stock to the left for left-handed shooters is “cast on.” Shims marked 1R1L, 2R2L and 3R3L, will all adjust drop at comb the same amount as shims 1, 2 and 3, and will also adjust the cast right or left approximately 1/8".
3 Remove the stock insert to access the stock bolt nut (Figure 24). FIGURE 24 4 Use a ½" socket wrench to remove the two stock bolt nuts and stock bolt washer. (Figure 25). 5 Completely remove the buttstock from the receiver, along with the existing shim, and install the shim you have selected (Figure 26). Make certain you have the proper shim installed and in position before reattaching the buttstock and recoil pad. Remove the stock insert.
I N S TA L L I N G S C O P E S O R O P T I C S BEFORE MOUNTING A SCOPE, SIGHT OR OTHER ACCESSORIES ON YOUR SHOTGUN, PLACE THE “SAFETY” IN THE ON SAFE POSITION. OPEN THE ACTION AND MAKE CERTAIN YOUR SHOTGUN IS COMPLETELY UNLOADED. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. Some Maxus shotguns are designed to accept a scope or other optical sight; usually these are turkey and deer models.
6 Pre-position the base on the receiver top to determine the best orientation of the base. Most bases have transverse grooves cut into them that are offset from the middle. These are the grooves that the crossbolts in your scope rings will pass through. The grooves are offset to allow you to position the bases to fit the design/length of your scope and the placement of the scope, front to rear for proper eye relief.
EXTRA BARRELS BEFORE INSTALLING AN ACCESSORY BARREL ON YOUR SHOTGUN, READ THE FOLLOWING GUIDELINES TO ENSURE THE BARREL/SHOTGUN COMBINATION IS SAFE. PLACE THE “SAFETY” IN THE ON SAFE POSITION. OPEN THE ACTION AND MAKE CERTAIN YOUR SHOTGUN IS COMPLETELY UNLOADED. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. The versatility of your new shotgun can be extended with an extra barrel.
these surfaces with a lightweight gun oil containing no solvents or with a damp cloth and mild dish soap (be sure to keep water out of the action). When cleaning your firearm’s bore and action, protect the external finishes from any contact with chemicals used. Also avoid any contact between external finishes and other strong chemicals like those found in DEET-containing insect repellents, sunscreens, etc.
Normal maintenance can be accomplished with the barrel still attached to the receiver (oiling and wiping down). More careful cleaning requires removal of the barrel from the receiver (cleaning the barrel) and the removal of the gas system components. A complete cleaning requires removal of the bolt and trigger group.
MOST SOLVENTS ARE HIGHLY FLAMMABLE. WEAR EYE PROTECTION AND PRACTICE APPROPRIATE SAFETY MEASURES WHEN WORKING WITH SOLVENTS TO AVOID SERIOUS INJURY. 6 After all leading and plastic residues have been removed, run a clean, dry patch through the bore. Follow this with a final, lightly oiled patch. 7 Reassemble the shotgun and wipe all exposed metal surfaces with an oiled cloth making sure to wipe away all finger marks where moisture could accumulate.
Note: If your Maxus uses a polymer piston sleeve, the gas system components (piston sleeve and gas piston) on your shotgun are not attached. Remove and clean them as outlined below. 2 Spray the magazine tube, gas piston and piston sleeve with gun solvent and brush them thoroughly with a nylon brush to remove any deposits. It will be easier to remove the piston sleeve spring to clean the interior of the piston sleeve. Spray the inside of the gas piston.
DO NOT PLACE LARGE QUANTITIES OF OIL INTO THE ACTION. EXCESS OIL WILL RUN BACK INTO THE WOOD OF THE STOCK SOFTENING THE WOOD, WITH CONSEQUENTIAL LOOSENING OF THE STOCK. SERVICING THE TRIGGER GROUP BEFORE REMOVING THE TRIGGER GROUP, PLACE THE “SAFETY” IN THE ON SAFE POSITION. OPEN THE ACTION AND MAKE CERTAIN YOUR SHOTGUN IS COMPLETELY UNLOADED. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.
FIGURE 28 FIGURE 29 Push the trigger group pins through the receiver. Lift the trigger group from the receiver. REMOVING THE TRIGGER GROUP 1 Place the bolt in the forward position by holding the operating handle and depressing the bolt release button. NEVER ALLOW THE ACTION TO SLAM CLOSED BY PRESSING THE BOLT RELEASE BUTTON WITHOUT THE BARREL INSTALLED. IF THE BOLT IS RELEASED FORWARD WITH THE BARREL REMOVED, THE OPERATING HANDLE WILL STRIKE THE RECEIVER AND CAUSE DAMAGE.
R E I N S TA L L AT I O N O F T H E T R I G G E R G R O U P 1 Make sure the bolt is in the forward position. 2 Insert the trigger group into the receiver. Align the holes in the trigger group with the holes on each side of the receiver. 3 Insert the trigger guard pins and gently tap them into place with a plastic or wooden mallet, using caution not to scratch the receiver. S E R V I C I N G T H E B O LT A S S E M B LY BEFORE REMOVING THE BOLT ASSEMBLY, PLACE THE “SAFETY” IN THE ON SAFE POSITION.
FIGURE 30 NEVER ALLOW THE ACTION TO SLAM CLOSED BY PRESSING THE BOLT RELEASE BUTTON WITHOUT THE BARREL INSTALLED. IF THE BOLT IS RELEASED FORWARD WITH THE BARREL REMOVED, THE OPERATING HANDLE WILL STRIKE THE RECEIVER AND CAUSE DAMAGE. 4 Remove the operating handle by pulling the operating handle outward (Figure 30). Pull outward to remove the bolt handle. FIGURE 31 5 Slide the bolt assembly forward and out of the receiver (Figure 31).
FIGURE 33 FIGURE 34 The bolt shown assembled. Guide the bolt slide link into its socket in the recoil spring follower. 3 Align the rails on the bolt slide with the grooves in the receiver. Press the bolt release button and slide the bolt assembly into the receiver, bolt slide link end first. 4 Ensure the bolt slide link fits into the socket in the recoil spring follower (Figure 34). 5 Replace the operating handle by inserting it in its slot in the bolt.
Wipe the receiver cavity clean. Lightly oil the cavity and wipe it dry. No further disassembly is required for cleaning. 2 Reassemble the trigger group, bolt assembly, gas system and the barrel to the receiver as explained previously. Then wipe all exposed metal surfaces with an oiled cloth, making sure to wipe clean all finger marks where moisture could accumulate. 3 The barrel and action should be inspected thoroughly to be certain no cleaning patches have been inadvertently left in them.
FIGURE 35 DO NOT ATTEMPT TO REMOVE THE ACTION SPRING FROM THE ACTION TUBE. THE ACTION TUBE IS EASILY DAMAGED AND THE ACTION SPRING IS UNDER SPRING TENSION. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DAMAGE YOUR SHOTGUN. 3 Hold the shotgun with the Place a few drops of oil in the opening in the action tube. muzzle down. Rotate the shotgun and cycle the action using the bolt handle to operate the action several times to evenly disperse the oil on the spring and inside the action tube.
REQUIRED, TAKE YOUR FIREARM TO A QUALIFIED GUNSMITH, OR CONTACT OUR ARNOLD, MISSOURI SERVICE FACILITY AS EXPLAINED UNDER “SERVICE OR REPAIR” ON PAGE 52. MAINTENANCE OF OIL FINISH STOCKS Keeping the oil-finished wood surface on your firearm looking its best requires only a small amount of maintenance. When the surface becomes spotted or dull, the affected area(s) can be treated using rubbing alcohol on a soft, lint free cloth and allowed to dry.
SERVICE OR REPAIR If your firearm should require service or repairs, we suggest you first contact a local recommended Browning Firearms Service Center. To locate a service center visit browning.com, contact our Customer Service Department or your Browning firearms dealer for the address of the Service Center nearest you. Otherwise, you may send your firearm directly to our Service Department in Arnold, Missouri.
BROWNING.
