BAR ® SHORTTRAC AND LONGTRAC ® AUTOLOADING RIFLE OWNER’S MANUAL ®
Important operating instructions for: BROWNING BAR SHORTTRAC® AND BAR LONGTRAC® AUTOLOADING RIFLES If you have any questions about your new firearm, this owner’s manual or other Browning products, contact: Browning Customer Service One Browning Place Morgan, UT 84050-9326 Phone: (800) 333-3288 browning.com Please use the space below to record information about your new firearm.
C O N T E N T S P A G E State Warning............................................................................................2 WARNING: You are Responsible for Firearms Safety............................2 General Description and Operation........................................................9 Nomenclature..........................................................................................10 Serial Number........................................................................................
S TAT E WA R N I N G According to state law, California requires that firearm manufacturers, distributors and retailers include conspicuous, specific warnings with firearms sold in that state. WA R N I N G : Y O U A R E R E S P O N S I B L E FOR FIREARMS SAFETY FAILURE TO FOLLOW ANY OF THE FOLLOWING WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. As a gun owner, you accept a set of demanding responsibilities. How seriously you take these responsibilities can be the difference between life and death.
Please read and understand all of the cautions, warnings, notices, proper handling procedures and instructions outlined in this owner’s manual before using your new firearm. 1 ALWAYS KEEP THE MUZZLE OF YOUR FIREARM POINTED IN A SAFE DIRECTION EVEN THOUGH YOU ARE CERTAIN IT IS UNLOADED. Never point any firearm at anything you do not intend to shoot. Be extremely alert and aware of all persons and property within the range of your ammunition.
3 WHENEVER YOU HANDLE ANY FIREARM, OR HAND IT TO SOMEONE, ALWAYS OPEN THE ACTION IMMEDIATELY AND VISUALLY CHECK THE FIREARM’S CHAMBER TO MAKE CERTAIN THAT THE FIREARM IS COMPLETELY UNLOADED. Make certain the firearm does not inadvertently contain any ammunition. Remember, merely removing the magazine does not mean the chamber is unloaded. Always keep the chamber empty and the “safety” in the on safe position unless shooting is imminent. 4 ALWAYS WEAR EAR AND EYE PROTECTION WHEN SHOOTING.
HUNTING FROM ELEVATED SURFACES SUCH AS TREESTANDS IS DANGEROUS. Doing so may increase the risk of mishandling a firearm. The following rules should always be observed by you and those you hunt with. Always make certain that the stand being used is safe and stable. Always make certain that your firearm is unloaded when it is being taken up and down from the stand. Always make certain that your firearm is not dropped from the stand, or dropped while it is being taken up or down from the stand.
10 BE ALERT TO THE SIGNS OF AMMUNITION MALFUNCTION. IF YOU DETECT AN OFF SOUND OR LIGHT RECOIL WHEN A CARTRIDGE IS FIRED, DO NOT LOAD ANOTHER CARTRIDGE INTO THE CHAMBER. If your firearm fails to fire, keep the muzzle pointed in a safe direction for a minimum of 30 seconds. Rotate the ejection area of the firearm away from you, carefully open the action and remove the cartridge from the chamber. If the primer is indented, the defective cartridge should be disposed of in a way that cannot cause harm.
cartridges of nonstandard dimensions or which develop pressures in excess of commercially available ammunition which has been loaded in accordance with standards established by the Sporting Arms and Ammunition Manufacturers’ Institute (SAAMI). 14 MAKE SURE OF ADEQUATE VENTILATION IN THE AREA THAT YOU DISCHARGE A FIREARM. LEAD EXPOSURE CAN OCCUR FROM DISCHARGING FIREARMS IN POORLY VENTILATED AREAS, CLEANING FIREARMS OR HANDLING AMMUNITION.
20 BE CERTAIN YOUR FIREARM IS UNLOADED BEFORE CLEANING. Because so many firearm accidents occur when a firearm is being cleaned, special and extreme care should be taken to be sure your firearm is unloaded before disassembly, cleaning and reassembly. Keep ammunition away from the cleaning location. Never test the mechanical function of any firearm with live ammunition. 21 TEACH AND SUPERVISE FIREARMS SAFETY TO ALL MEMBERS OF YOUR FAMILY, ESPECIALLY TO CHILDREN AND NON-SHOOTERS.
25 WE RESERVE THE RIGHT TO REFUSE SERVICE ON FIREARMS THAT HAVE BEEN ALTERED, ADDED TO OR SUBSTANTIALLY CHANGED. Removal of metal from the barrel, or modifications of the firing mechanism and/or operating parts, may lead to a refusal of service on such firearms. We will charge you for parts and labor to return the firearm to original specifications. DO NOT, UNDER ANY CIRCUMSTANCES, ALTER THE TRIGGER, SAFETY OR OTHER PARTS OF THE FIRING MECHANISM OF THIS OR ANY OTHER FIREARM.
N O M E N C L AT U R E In conventional firearm terminology the position and movement of firearm parts are described as they occur with the firearm horizontal and in the normal firing position: i.e., the muzzle is forward or in front; the buttstock is rearward or to the rear; the trigger is downward or underneath; the sight is upward or on top. For general parts nomenclature, refer to Figure 1 on page 9. SERIAL NUMBER The serial number is located on the left side of the receiver, above the trigger guard.
CLEANING Various exposed metal parts of your new firearm have been coated at the factory with a rust preventative compound. Before firing your rifle, clean the anti-rust compound from the inside of the barrel, receiver and the action/chamber areas. A high-quality lightweight gun oil is ideal for removing this compound, and for giving your new firearm its first lubrication. Clean the barrel using a cleaning rod and patch as explained under “Cleaning and Maintenance Suggestions” on pages 26-29.
the safety button to the left. This exposes the red warning band on the “safety” button (Figure 3, page 11). DO NOT DEPEND ON THE RED COLOR ALONE TO INDICATE YOUR FIREARM’S SAFETY STATUS. TIME, EXPOSURE TO THE ELEMENTS, AND THE ABRASIVE ACTION OF CLEANING AGENTS CAN ERASE IT. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH. The “safety” can be reversed from right- to left-handed by a qualified gunsmith.
position, pull the operating handle all the way to the rear and press upward on the bolt lock. FIGURE 4 To release the bolt when no magazine is in the rifle and the bolt is locked rearward, pull the operating handle to the rear to disengage the bolt lock and release the handle. This allows the bolt to return to the forward position. AMMUNITION The location of the bolt lock. DO NOT USE AMMUNITION OTHER THAN WHAT IS INSCRIBED ON THE RIGHT SIDE OF THE BARREL.
Another cartridge may be carried in the chamber, providing a total rifle capacity of five cartridges for standard calibers and four cartridges for magnum and WSM calibers. Remember, total rifle capacity includes an additional cartridge which can be loaded in the chamber in addition to a full magazine. LOADING THE MAGAZINE WHEN LOADING YOUR RIFLE ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION, ALWAYS PLACE THE “SAFETY” IN THE ON SAFE POSITION AND KEEP YOUR FINGERS AWAY FROM THE TRIGGER.
FIGURE 5 FIGURE 6 Pull rearward on the magazine latch to access the magazine. Press the cartridge into the magazine until it is retained by the magazine feed lips. 3 Pull the bolt completely rearward and inspect the chamber to make sure it is empty. Return the bolt to the forward, closed position. 4 Lay a cartridge on top of the magazine follower and press the cartridge down with your thumb until it is retained in the magazine (Figure 6). Load subsequent cartridges into the magazine in the same manner.
FIGURE 7 FIGURE 8 Grasp the sides of the magazine and detach it from the floorplate. Press the cartridge into the magazine until it is retained by the magazine feed lips. 3 Pull the bolt completely rearward and inspect the chamber to make sure it is empty. Return the bolt to the forward, closed position. 4 Detach the magazine from the floorplate by grasping the sides of the magazine and pulling it off the hinged floorplate (Figure 7).
LOADING THE CHAMBER WHEN LOADING YOUR RIFLE ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION, ALWAYS PLACE THE “SAFETY” IN THE ON SAFE POSITION AND KEEP YOUR FINGERS AWAY FROM THE TRIGGER. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. DO NOT CARRY YOUR RIFLE WITH A CARTRIDGE IN THE CHAMBER TO AVOID ACCIDENTAL DISCHARGE. WHEN FIRING IS NO LONGER IMMINENT, MAKE SURE THE “SAFETY” IS IN THE ON SAFE POSITION AND UNLOAD THE CHAMBER.
near the ejection port (Figure 9). You should first practice this technique with an empty chamber. FIGURE 9 It is safer to hunt with an empty chamber until in the presence of game. In this situation, quietly chambering a cartridge is important. To quietly chamber a cartridge, cycle the action slowly by pulling the operating handle to The bolt is fully forward when the bolt its full rearward position, then forward indicator is exposed.
4 After a cartridge has fired, the bolt automatically moves rearward, ejects the empty case, then returns forward, chambering a cartridge from the magazine. Because fired cases are ejected to the side, bystanders should not stand to the side of the shooter. 5 This operation is repeated each time you pull the trigger until the last cartridge from the magazine has been fired. If shooting is no longer imminent, immediately place the “safety” in the on safe position.
UNLOADING THE RIFLE 1 Make sure the “safety” is in the on safe position and the muzzle is pointed in a safe direction. 2 Pull rearward on the magazine latch in front of the trigger guard and allow the hinged floorplate and magazine unit to swing downward. 3 Pull rearward on the operating handle to draw the bolt to its rearmost, open position. This will extract and eject any live cartridge that may be in the chamber.
MOUNTING A SCOPE BEFORE MOUNTING A SCOPE, SIGHT OR OTHER ACCESSORIES TO YOUR RIFLE, PLACE THE “SAFETY” IN THE ON SAFE POSITION. OPEN THE ACTION AND MAKE CERTAIN YOUR RIFLE IS COMPLETELY UNLOADED. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. The top of the BAR ST/LT receiver is drilled and tapped for scope bases. From the factory, the scope base holes are fitted with filler screws.
Many gunsmiths find it helpful to use a drop of serviceable thread locking compound to assure the screws stay tight. Make sure the thread locking compound does not get into the action. Be careful to insure that the threads of each screw engage properly in the receiver to prevent stripping the threads in the receiver. 7 Tighten the screws snugly, but do not overtighten. 8 Mount your scope rings and scope as outlined in the instructions supplied with your scope rings and/or scope.
install a recoil pad perform the following operation: FIGURE 11 1 Make sure your rifle is completely unloaded and the “safety” is in the on safe position. 2 Use a #2 cross tip or Phillips screwdriver to remove the recoil pad at the end of the buttstock (Figure 11). Place a Carefully loosen the screws that attach the small amount of petroleum recoil pad to the buttstock. jelly on the screw access slits on the top and bottom of the rear of the recoil pad to prevent damaging the recoil pad.
A D J U S T I N G C A S T A N D D R O P AT C O M B Six shims have been included with BAR ST/LT rifles (Figure 12, page 23). The shims fit between the buttstock and receiver, allowing customized adjustments to the comb and heel. Each shim is labeled/ stamped for a specific amount of adjustment. The neutral shim, No. 2, is already installed on your firearm. Drop at comb is defined as the place on the comb that your cheek rests when taking aim.
• Shim 2R2L adds the same amount of cast to the stock as shim 1RL and the same amount of drop to the comb as shim No. 2. • Shim 3R3L adds the same amount of cast to the stock as 2RL and 3RL, and lowers the comb approximately 1/16" and the heel approximately 1/8". T O I N S TA L L A S H I M 1 Make sure your firearm is completely unloaded and the “safety” is in the on safe position. 2 Use a #2 cross tip or Phillips screwdriver to remove the recoil pad at the end of the buttstock (Figure 11, page 23).
FIGURE 15 The six stock shims move the stock as shown above Make certain you have the proper shim installed and in position before reattaching the buttstock and recoil pad (Figure 15). NOTICE! DO NOT USE MORE THAN ONE SHIM ON THE BUTTSTOCK . 5 When you are satisfied with the fit, reattach the buttstock to the receiver with the washer and the screw. 6 Snug the stock screw with a screwdriver, do not overtighten. 7 Attach the recoil pad with care, so as not to scratch or mar the finish of the stock.
cloth and mild dish soap (be sure to keep water out of the action). When cleaning your firearm’s bore and action, protect the external finishes from any contact with chemicals used. Also, avoid any contact between external finishes and other strong chemicals like those found in DEET-containing insect repellents, sunscreens, etc. Damage to camouflage, Dura-Touch and other finishes caused by chemicals is irreversible and not repairable.
If you encounter a function problem be sure to give your firearm a thorough cleaning to see if it solves the problem before seeking the services of a Browning Recommended Service Center or our Service Facility in Arnold, Missouri, or a qualified gunsmith. 1 Lock the bolt in the open position as explained previously. 2 Inspect the chamber and bore for powder fouling. A normal amount of powder residue can be expected and is not serious. It can usually be removed with a patch saturated with nitro solvent.
4 Inspect the barrel and chamber to be certain no patches have inadvertently been left in them. Remove any that remain. 5 Use a small brush or rag to remove dirt or other foreign matter from inside the receiver and other parts of the action. Lightly lubricate all moving parts with a high-quality, light gun oil. Use oil sparingly, a very light film is sufficient. A fine, light gun oil is ideally suited for this purpose. NOTICE! DO NOT POUR LARGE QUANTITIES OF OIL INTO THE RECEIVER OR OTHER PARTS.
FIGURE 16 FIGURE 17 Tap the trigger group pins through the receiver. Lift the trigger group from the receiver. If any service of the trigger group or bolt becomes necessary, contact our Service Facility in Arnold, Missouri, or a qualified gunsmith. T R I G G E R G R O U P R E M O VA L 1 Be certain the rifle is completely unloaded and the “safety” is in the on safe position. 2 Release the bolt to its forward position by pressing down on the bolt lock as detailed previously.
T R I G G E R G R O U P I N S TA L L AT I O N 1 Before reinstalling the trigger group, make sure that the bolt is fully forward and engaged in the locked position. 2 Visually check the “safety” on the trigger guard to make certain it is still in the on safe position. 3 Insert the trigger group back into the receiver, lining up the holes in the trigger group with the holes on each side of the receiver.
NOTICE! NEVER ATTEMPT TO TAKE YOUR FIREARM APART FURTHER THAN EXPLAINED IN THIS OWNER’S MANUAL. YOUR FIREARM IS A SPECIALIZED, FINELY FITTED MECHANISM. YOU MAY PERMANENTLY DAMAGE IT BY ATTEMPTING TO DISASSEMBLE THE INNER MECHANISM ASSEMBLIES. IF FURTHER DISASSEMBLY FOR SERVICE OR CLEANING IS REQUIRED, TAKE YOUR FIREARM TO A QUALIFIED GUNSMITH, OR CONTACT OUR ARNOLD, MISSOURI SERVICE FACILITY AS EXPLAINED ON PAGE 33 UNDER “SERVICE OR REPAIR.
SERVICE OR REPAIR If your firearm should require service or repairs, we suggest you first contact a local recommended Browning Firearms Service Center. To locate a service center visit browning.com, contact our Customer Service Department or your Browning firearms dealer for the address of the Service Center nearest you. Otherwise, you may send your firearm directly to our Service Department in Arnold, Missouri.
NOTES 34
NOTES 35
NOTES 36
BROWNING.
