FBPL Command Reference
Table Of Contents
- 1 Example of Command Reference
- 2 Document Conventions
- 3 Object Position Calculation
- 4 Supported Printers
- 5 Setup and System Commands
- 5.1 SIZE
- 5.2 GAP
- 5.3 GAPDETECT
- 5.4 BLINEDETECT
- 5.5 AUTODETECT
- 5.6 BLINE
- 5.7 OFFSET
- 5.8 SPEED
- 5.9 DENSITY
- 5.10 DIRECTION
- 5.11 REFERENCE
- 5.12 SHIFT
- 5.13 COUNTRY
- 5.14 CODEPAGE
- 5.15 CLS
- 5.16 FEED
- 5.17 BACKFEED
- 5.18 FORMFEED
- 5.19 HOME
- 5.20 PRINT
- 5.21 SOUND
- 5.22 CUT
- 5.23 LIMITFEED
- 5.24 SELFTEST
- 5.25 EOJ
- 5.26 DELAY
- 5.27 DISPLAY
- 5.28 INITIALPRINTER
- 5.29 MENU
- 6 Label Formatting Commands
- 7 Status Polling and Immediate Commands
- 8 Commands for Windows Driver
- 9 File Management Commands
- 10 BASIC Commands and Functions
- 10.1 ABS()
- 10.2 ASC()
- 10.3 CHR$()
- 10.4 XOR$()
- 10.5 END
- 10.6 EOF()
- 10.7 OPEN
- 10.8 CLOSE
- 10.9 WRITE
- 10.10 READ
- 10.11 SEEK
- 10.12 LOF()
- 10.13 LOC()
- 10.14 FREAD$()
- 10.15 PUT
- 10.16 GET
- 10.17 COPY
- 10.18 FOR…NEXT LOOP
- 10.19 WHILE…WEND
- 10.20 DO…LOOP
- 10.21 IF…THEN…ELSE…ENDIF LOOP
- 10.22 GOSUB…RETURN
- 10.23 GOTO
- 10.24 INP$()
- 10.25 INP()
- 10.26 LOB()
- 10.27 INPUT
- 10.28 PREINPUT
- 10.29 POSTINPUT
- 10.30 SET FILTER
- 10.31 REM
- 10.32 OUT
- 10.33 OUTR
- 10.34 GETKEY()
- 10.35 INT()
- 10.36 LEFT$()
- 10.37 LEN()
- 10.38 MID$()
- 10.39 RIGHT$()
- 10.40 STR$()
- 10.41 STRCOMP()
- 10.42 INSTR()
- 10.43 TRIM$()
- 10.44 LTRIM$()
- 10.45 RTRIM$()
- 10.46 TEXTPIXEL()
- 10.47 BARCODEPIXEL()
- 10.48 VAL()
- 10.49 NOW$()
- 10.50 NOW
- 10.51 FORMAT$()
- 10.52 DATEADD()
- 10.53 FSEARCH()
- 10.54 TOUCHPRESS()
- 10.55 RECORDSET$()
- 10.56 REPLACE$()
- 11 Device Reconfiguration Commands
- 11.1 SET COUNTER
- 11.2 SET CUTTER
- 11.3 SET PARTIAL_CUTTER
- 11.4 SET BACK
- 11.5 SET BACK_BEFORE_PRINT
- 11.6 SET KEYn
- 11.7 SET LEDn
- 11.8 SET PEEL
- 11.9 SET REWIND
- 11.10 SET TEAR
- 11.11 SET GAP
- 11.12 SET BLINE REVERSE / SET BLINE OBVERSE
- 11.13 SET BLINE PRINTSIDE / SET BLINE BACKSIDE
- 11.14 SET HEAD
- 11.15 SET RIBBON
- 11.16 SET ENCODER
- 11.17 SET RIBBONEND
- 11.18 SET COM1
- 11.19 SET PRINTKEY
- 11.20 SET REPRINT
- 11.21 SET FEED_LEN
- 11.22 GETSENSOR()
- 11.23 GETSETTING$()
- 11.24 SET USBHOST
- 11.25 SET AUTORUN
- 11.26 SET RESPONSE
- 11.27 SET DAYLIGHT_SAVE
- 11.28 SET REGISTRATION
- 11.29 PEEL
- 11.30 LED1, LED2, LED3
- 11.31 KEY1, KEY2, KEY3
- 11.32 SET SENSOR_REF
- 12 Printer Global Variables
- 13 Bluetooth Module Setting Commands
- 14 Wi-Fi Module Setting Commands
- 15 Internal Ethernet Setting Commands
- 16 Setting Commands for RJ-2035B/2055WB/3035B/3055WB
- 17 RFID
- 18 General purpose input output (GPIO) Setting Commands
- Appendix A: Command List by Model
- Appendix B: Download your Fonts
30
5.23 LIMITFEED
Description
If the gap sensor is not set to a suitable sensitivity while feeding labels, the printer will not be able to locate
the correct position of the gap. This command stops label feeding and makes the red LED flash if the printer
does not locate gap after feeding the length of one label plus one preset value.
Syntax
LIMITFEED n[,minpaper,maxgap]
inch
LIMITFEED n mm[,minpaper mm,maxgap mm]
mm
LIMITFEED n dot[,minpaper dot,maxgap dot]
dot
Parameter
Description
n
The maximum length for the sensor detection
Minpaper
The minimum length of paper
Maxgap
The maximum length of gap
Note:
▪ The setting will remain resident in memory.
▪ For metric system, make sure you add a space between parameter n and mm.
▪ The setting will return to the default value (10 inches) when the printer is initialized.
▪ If the printer cannot calibrate the pre-printed media or media with hole, type the Minpaper
or Maxgap.
Example
Sample code
LIMITFEED 12
LIMITFEED 10, 2.36, 0.12
LIMITFEED 250 mm, 60 mm, 3 mm
LIMITFEED 2000 dot, 480 dot, 24 dot