Software Developer’s Manual DPL Emulation Guide TD-4420TN/4520TN TD-4650TNWB/4650TNWBR/4750TNWB/4750TNWBR TJ-4005DN/4010TN TJ-4020TN/4021TN/4021TNR/4120TN/4121TN/4121TNR TJ-4420TN/4520TN/4620TN/4422TN/4522TN Version 5.
Copyright ©2020 Brother Industries, Ltd. All rights reserved. Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement. The software may be used or copied only in accordance with the terms of those agreements. No part of this publication can be reproduced in any form or by any means without prior written permission of Brother Industries, Ltd.
Table of Contents 1. Introduction························································································ 2 2. Printer Settings ··················································································· 3 3.
1. Introduction DPL emulation allows TD-4T and TJ Printers to interpret DPL commands. To use this feature, change the printer settings as described in Section 2.
2. Printer Settings The TD-4T and TJ Printers have built-in paper settings that are necessary to perform printing operations (position detection). The settings are saved in the device’s flash memory so they are retained even if the power is turned off. Before using the DPL emulation, printer settings (such as the paper size and type) must be set using the Brother Printer Management Tool (BPM): a. Start the BPM. b. Click the Printer Function. c. Select the calibration sensor, and click the Calibrate. d.
3.
Classification Extended System-Level Command Comment M Set Maximum Label Length m Set Printer to Metric Mode n Set Printer to Imperial Mode O Set Start of Print (SOP) Position o Cycle Cutter P Set Printer to Character (HEX) Dump Mode p Controlled Pause Q Clear All Modules q Clear Module R Ribbon Saver On/Off r Select Reflective Sensor S Set Feed Rate s Set Single Buffer Mode t Test DRAM Memory Module U
Classification Command Comment Models only) Label Formatting Command KS Memory Configuration, Scalable Font Cache KV Verifier Enable/Disable KW Memory Configuration, Printable Label Width Kx Delete Configuration File KZ Immediately Set Parameter : Set Cut By Amount A Set Format Attribute B Bar Code Magnification C Set Column Offset Amount c Set Cut By Amount D Set Dot Size Width and Height E Terminate Label Formatting Mode and Print Label F Advanced Form
Classification Command Comment s Store Label Format in Module T Set Field Data Line Terminator X Terminate Label Formatting Mode y Select Font Symbol Set z Zero (Ø) Conversion to "0" + (>)(() "Make Last Field Entered Increment Numeric (Alphanumeric)(Hexadecimal)" – (<)()) "Make Last Field Entered Decrement Numeric (Alphanumeric)(Hexadecimal)" + (>) Make Last Field Entered Increment Numeric (Alphanumeric) - (<) Make Last Field Entered Decrement Numeric (Alphanumeric) ^ Set Count by Amou
Appendix A: Supported Printers TD-4420TN TD-4520TN TD-4T series TD-4650TNWB TD-4650TNWBR TD-4750TNWB TD-4750TNWBR TJ-4005DN TJ-4010TN TJ-4020TN TJ-4021TN TJ-4021TNR TJ-4120TN TJ series TJ-4121TN TJ-4121TNR TJ-4420TN TJ-4520TN TJ-4620TN TJ-4422TN TJ-4522TN -8-
Appendix B: Font Specification The font specifications compatible with TD-4T and TJ Printer DPL Emulation are as follows: 0DMX.BMF 1DMX.BMF 2DMX.BMF 3DMX.BMF Fixed Font 4DMX.BMF 5DMX.BMF 6DMX.BMF 7DMX.BMF Built-in Font 8DMX.BMF 00DMX.TTF 01DMX.TTF A0DMX.TTF Scalable Font A1DMX.TTF A2DMX.TTF A3DMX.
Appendix C: Supported Barcodes Barcode ID Type A / a Code 3 of 9 B / b UPC-A C / c UPC-E D / d Interleaved 2 of 5 (12 of 5) E / e Code 128 F / f EAN-13 G / g EAN-8 H / h HBIC I / i Codabar J / j Interleaved 2 of 5 with a modulo 10 checksum K / k Plessey L / l Interleaved 2 of 5 with a modulo 10 checksum & shipping bearer bars M / m 2 digit UPC addendum N / n 5 digit UPC addendum O / o Code 93 p Postnet Q / q UCC/EAN Code 128 R / r UCC/EAN Code 128 K-Mart NON EDI barcode
