P-touch Template Manual/ Command Reference
Table Of Contents
- P-Touch Template Manualv
- P-Touch Template Command Referencev
- Control Code List
- About P-touch Template
- Static and dynamic commands
- If printing does not begin (main most frequent causes)
- If a template linked to a database is not printed
- Control Command Details
- ^PT Specify print start trigger selection
- ^FF Start printing
- ^PS Specify print start command text string
- ^PC Specify print start received character count
- ^SS Specify delimiter
- ^TS Specify template selection
- ^CO Specify machine settings (cut options)
- ^LS Specify line spacing with line return
- ^CC Change the prefix character
- ^RC Specify line return command text string
- ^CN Specify number of copies
- ^NN Specify number of Numbering copies
- ^ID Initialize template data
- ^QS Specify print options
- ^QV Specify QR code version
- ^FC FNC1 replacement setting
- ^II Initialize
- ^OP Perform machine operation (feed/cut)
- ^SR Status request
- ^VR Retrieve version Information
- ^CR Line return in object
- ^OS Specify object selection (object number)
- ^ON Specify object selection (object name)
- ^DI Direct object insertion
- ESC ia Specify command mode
- ESC iXT2 Specify print start trigger selection
- ESC iXP2 Specify print start command text string
- ESC iXr2 Specify print start received character count
- ESC iXD2 Specify delimiter
- ESC iXa2 Specify Non-Printed character text strings
- ESC iXi2 Specify command mode
- ESC iXn2 Specify template selection
- ESC iXf2 Change the prefix character
- ESC iXc2 Specify machine settings (cut options)
- ESC iXy2 Specify machine settings (cut options–specify cutting after a number of labels)
- ESC iXm2 Select character code set
- ESC iXj2 Specify international character set
- ESC iXR2 Specify line return command text string
- ESC iXC2 Specify number of copies
- ESC iXN2 Specify number of Numbering copies
- ESC iXF2 FNC1 replacement setting
- ESC iXq2 Specify print options
- ESC iXT1 Retrieve select print start trigger items
- ESC iXP1 Retrieve print start command setting text string
- ESC iXr1 Retrieve print start received character count
- ESC iXD1 Retrieve delimiter
- ESC iXa1 Retrieve Non-Printed character text strings
- ESC iXi1 Retrieve command mode setting
- ESC iXn1 Retrieve template selection number
- ESC iXc1 Retrieves machine settings (cut options)
- ESC iXy1 Retrieve machine settings (cut options–specify cutting after a number of labels)
- ESC iXm1 Retrieve character code set
- ESC iXj1 Retrieve international character set setting
- ESC iXf1 Retrieve the prefix character
- ESC iXR1 Retrieve line return command setting text string
- ESC iXC1 Retrieve number of copies
- ESC iXN1 Retrieve number of Numbering copies setting
- ESC iXF1 Retrieve FNC1 replacement setting
- ESC iXq1 Retrieve print options
- International character set table
Error information 1
Flag Mask Definition
Bit 0 0x01 "No media” error
Bit 1 0x02 “End of media” error
Bit 2 0x04 “Tape cutter jam” error
Bit 3 0x08 Not used
Bit 4 0x10 Machine in use
Bit 5 0x20 Machine turned off
Bit 6 0x40 Not used
Bit 7 0x80 Fan motor error
Error information 2
Flag Mask Definition
Bit 0 0x01 “Replace the media.” error
Bit 1 0x02 “Expansion buffer is full.” error
Bit 2 0x04 Transmission error
Bit 3 0x08 Image error occurred
Bit 4 0x10 “Cover open” error
Bit 5 0x20 Not used
Bit 6 0x40 Leading edge detection error
Bit 7 0x80 System error
Media type
Media type Value Remarks
Continuous length label
4A Hex
Die-cut label
4B Hex
Status type
Status type Value
Reply to status request 00 Hex
(Not used) 01 Hex
Error occurred 02 Hex
(Not used) 03 Hex to FF Hex
27