P-touch Template Manual/ Command Reference
Table Of Contents
- P-Touch Template Manualv
- P-Touch Template Command Referencev
- Control Code List
- About P-touch Template
- Static and dynamic commands
- If printing does not begin (main most frequent causes)
- If a template linked to a database is not printed
- Control Command Details
- ^PT Specify print start trigger selection
- ^FF Start printing
- ^PS Specify print start command text string
- ^PC Specify print start received character count
- ^SS Specify delimiter
- ^TS Specify template selection
- ^CO Specify machine settings (cut options)
- ^LS Specify line spacing with line return
- ^CC Change the prefix character
- ^RC Specify line return command text string
- ^CN Specify number of copies
- ^NN Specify number of Numbering copies
- ^ID Initialize template data
- ^QS Specify print options
- ^QV Specify QR code version
- ^FC FNC1 replacement setting
- ^II Initialize
- ^OP Perform machine operation (feed/cut)
- ^SR Status request
- ^VR Retrieve version Information
- ^CR Line return in object
- ^OS Specify object selection (object number)
- ^ON Specify object selection (object name)
- ^DI Direct object insertion
- ESC ia Specify command mode
- ESC iXT2 Specify print start trigger selection
- ESC iXP2 Specify print start command text string
- ESC iXr2 Specify print start received character count
- ESC iXD2 Specify delimiter
- ESC iXa2 Specify Non-Printed character text strings
- ESC iXi2 Specify command mode
- ESC iXn2 Specify template selection
- ESC iXf2 Change the prefix character
- ESC iXc2 Specify machine settings (cut options)
- ESC iXy2 Specify machine settings (cut options–specify cutting after a number of labels)
- ESC iXm2 Select character code set
- ESC iXj2 Specify international character set
- ESC iXR2 Specify line return command text string
- ESC iXC2 Specify number of copies
- ESC iXN2 Specify number of Numbering copies
- ESC iXF2 FNC1 replacement setting
- ESC iXq2 Specify print options
- ESC iXT1 Retrieve select print start trigger items
- ESC iXP1 Retrieve print start command setting text string
- ESC iXr1 Retrieve print start received character count
- ESC iXD1 Retrieve delimiter
- ESC iXa1 Retrieve Non-Printed character text strings
- ESC iXi1 Retrieve command mode setting
- ESC iXn1 Retrieve template selection number
- ESC iXc1 Retrieves machine settings (cut options)
- ESC iXy1 Retrieve machine settings (cut options–specify cutting after a number of labels)
- ESC iXm1 Retrieve character code set
- ESC iXj1 Retrieve international character set setting
- ESC iXf1 Retrieve the prefix character
- ESC iXR1 Retrieve line return command setting text string
- ESC iXC1 Retrieve number of copies
- ESC iXN1 Retrieve number of Numbering copies setting
- ESC iXF1 Retrieve FNC1 replacement setting
- ESC iXq1 Retrieve print options
- International character set table
^CO Specify machine settings (cut options)
[ASCII] ^ C O n1 n2 n3 n4
[Decimal] 94 67 79 nd1 nd2 nd3 nd4
[Hexadecimal] 5E 43 4F nh1 nh2 nh3 nh4
[Parameters] 0≤n1≤1
0≤n2≤9
0≤n3≤9
0≤n4≤1
[Description]
・Specifies the various cut options.
n1: Auto cut setting
(ON: 1 (default); OFF: 0)
(n2*10)+n3: Auto cut label number setting (1 to 99)
(Default value: 1)
n4: Cut at end setting
(ON: 1 (default); OFF: 0)
・This command is a dynamic command.
[Remarks]
・The auto cut label number setting can be between 1 and 99. This is invalid when an
attempt is made to specify a value other than these.
[Example]
・To cut after every two labels:
Since the auto cut setting will be set to ON and the auto cut label number will be two
labels, n1=1, n2=0 and n3=2. Therefore, the command will be as follows.
^ C O 1 0 2 0
(5Eh 43h 4Fh 31h 30h 32h 30h)
14