Instruction Manual for Roll Feeder 2

29
If the machine stops operating correctly, check the following possible problems as well as the FAQ on the Brother Solutions Center
(http://s.brother/cpoac/) before requesting service. If the problem persists, contact Brother Customer Service or Brother authorized
service center. An asterisk (*) listed as a reference page indicates the Operation Manual for the cutting machine.
Material
* For details, refer to the Operation Manual for the cutting machine.
Troubleshooting
Symptom Possible cause (or result) Solution Reference
The material cannot be inserted.
When the leader sheet was inserted, it was
not placed under the feed rollers.
Insert the leader sheet so that it is placed under
the left and right feed rollers.
 page 15
was not used to insert the leader
sheet.
Lightly insert the leader sheet into the feed slot,
and then press .
 page 15
The feed roller is not correctly positioned. Adjust the position of the feed roller.  page 9
The shaft is unlocked. Lock the shaft.  page 10
“Roll Feeder” was not selected in the home
screen.
Select “Roll Feeder” in the home screen.  page 9
The material is not fed in
straight.
The end of the material is not evenly
trimmed.
Evenly trim the end of the material.  page 12
The leader sheet was inserted into the feed
slot at an angle.
Align the left edge of the leader sheet with the
rolled material guide, and then insert the leader
sheet straight into the feed slot.
 page 15
The material is not appropriately secured by
the guide plates.
Firmly secure the material with the guide plates.  page 11
The rear tray is not pulled out. Pull out the rear tray.  *
The feed roller is not correctly positioned. Adjust the position of the feed roller.  page 9
The material is not attached in the proper
position on the leader sheet.
Reattach the material so that it is aligned with the
attachment position line of the leader sheet.
 page 14
The adhesiveness of the leader sheet is
weak, or the material is not securely
attached.
Replace it with a new leader sheet. —
The edge of the leader sheet is worn. Replace it with a new leader sheet. —
The material cannot be fed.
There is an obstruction around the slot of
the machine.
Maintain space around the slot of the machine so
that the material can be fed out.
—
The machine is installed on a surface that is
not level.
Place the machine on a level, even surface. —
The leader sheet comes off
completely
There is an obstruction around the slot of
the machine.
Maintain space around the slot of the machine so
that the material can be fed out.
—
The material cannot be fed out.
The material to be cut is jammed in the
feeding mechanism in the machine.
Remove any jammed material according to the
procedures in “When Material Has Become
Jammed in the Machine” on page 31.
 page 31
After cutting off the material, the material
being fed out was too short and remained in
the machine.
Remove any material that could not be fed out
and stayed in the machine.
 page 32
The material became jammed.
The material was not fed straight.
Remove any jammed material according to the
procedures in “When Material Has Become
Jammed in the Machine” on page 31. After evenly
trimming the end of the material, feed the material
in straight.
 page 31
 page 12
 page 15
You are using a cutting material that is not
compatible with this product.
Replace it with a cutting material that is
compatible with this product.
 page 36
The blade is dull Replace it with a new blade.  *
“Cut Speed” and “Cut Pressure (Half Cut)”
are not appropriate.
Decrease the setting value for "Cut Speed" and
"Cut Pressure (Half Cut)" in the setting screen.
 *
The material moves to an
unintended position.
- The cutting start position was
unintentionally changed.
- The appropriate operation was not
selected after the pattern was cut.
Change the cutting start position to move the
material to the desired position. Press in the
operation panel to feed out the material toward
you.
 page 22