P-touch Template Manual/ Command Reference
Table Of Contents
- PT-9800PCN_PT-9700PC_P-touchTemplate_ver103.pdf
- PT-9800PCN_PT-9700PC_CmdRef_ver103.pdf
- Control code list
- About P-touch Template
- Static and dynamic commands
- If printing does not begin (main most frequent causes)
- Control command details
- ^PT Select print start trigger
- ^PS Specify print start command text string
- ^PC Specify print start received character count
- ^SS Specify delimiter
- ^TS Select template
- ^CF Full cut setting
- ^CH Half cut setting
- ^CP Chain printing setting
- ^MP Mirror printing setting
- ^SP Special tape setting
- ^LS Specify line spacing with line feed
- ^CC Change prefix character
- ^RC Specify line feed command text string
- ^CN Specify number of copies
- ^NN Specify number of Numbering copies
- ^ID Initialize template data
- ^QV Specify QR Code version
- ^FC FNC1 replacement setting
- ^II Initialize
- ^OP Perform machine operations (feed/cut)
- ^S R Status request
- ^V R Retrieve version Information
- ^CR Line feed in object
- ^OS Select object (object number)
- ^ON Select object (object name)
- ^DI Directly insert object
- ESC ia Specify command mode
- ESC iXT2 Select print start trigger
- ESC iXP2 Specify print start command text string
- ESC iXr2 Specify print start received character count
- ESC iXD2 Specify delimiter
- ESC iXa2 Specify non-printed text strings
- ESC iXi2 Specify command mode
- ESC iXn2 Select template
- ESC iXf2 Change prefix character
- ESC iXc2 Specify machine settings (full cut option)
- ESC iXy2 Specify machine settings (full cut option–specify cutting after specified number of labels)
- ESC iXH2 Half cut setting
- ESC iXM2 Mirror printing setting
- ESC iXs2 Special tape setting
- ESC iXm2 Select character code set
- ESC iXj2 Specify international character set
- ESC iXR2 Specify line feed command text string
- ESC iXC2 Specify number of copies
- ESC iXN2 Specify number of Numbering copies
- ESC iXF2 FNC1 replacement setting
- ESC iXT1 Retrieve select print start trigger items
- ESC iXP1 Retrieve print start command setting text string
- ESC iXr1 Retrieve print start received character count
- ESC iXD1 Retrieve delimiter
- ESC iXa1 Retrieve non-printed text strings
- ESC iXi1 Retrieve command mode setting
- ESC iXn1 Retrieve template selection number
- ESC iXc1 Retrieves machine settings (full cut option)
- ESC iXy1 Retrieve machine settings (full cut option–specify cutting after specified number of labels)
- ESC iXH1 Retrieve half cut setting
- ESC iXM1 Retrieve mirror printing setting
- ESC iXs1 Retrieve special tape setting
- ESC iXm1 Retrieve character code set
- ESC iXj1 Retrieve international character set setting
- ESC iXf1 Retrieve the prefix character
- ESC iXR1 Retrieve line feed command setting text string
- ESC iXC1 Retrieve number of copies setting
- ESC iXN1 Retrieve number of Numbering copies setting
- ESC iXF1 Retrieve FNC1 replacement setting
- Character code table
- International character set table
- Appendix: Specifications
16
^CP Chain printing setting
[ASCII] ^ C P n
[Decimal] 94 67 80 nd
[Hexadecimal] 5E 43 50 nh
[Parameters] 0≤n≤1
[Description]
・Specifies whether or not chain printing is applied.
n: Chain printing setting
(OFF: 0 (default); ON: 1)
・This command is a dynamic command.
[Remarks]
・Invalid if n is a value other than 1 or 0
[Example]
・To use chain printing:
Since chain printing will be enabled, n=1. Therefore, the command will be as follows.
^ C P 1
(5Eh 43h 50h 31h)