Quick Start Manual
Table Of Contents
- Contents
- Before Using
- Getting Started
- Introduction
- About this Chapter
- Using the Auto Punch Function
- Using Design Center
- Using Layout & Editing
- Step 1 Starting Layout & Editing
- Step 2 Importing Embroidery Patterns from Design Center
- Step 3 Zooming In and Out
- Step 4 Moving the Embroidery Pattern
- Step 5 Adding an Oval
- Step 6 Adjusting the Size and Location of the Oval
- Step 7 Adding Text
- Step 8 Fitting the Text around the Oval
- Step 9 Moving the Oval and Text
- Step 10 Adding a Circle for Drawing the Sun
- Step 11 Selecting a Programmable Fill Stitch
- Step 12 Adding Broken Lines for Drawing the Sun Rays
- Step 13 Changing the Sewing Order of Sun and Rays
- Step 14 Adjusting the Rays
- Step 15 Setting Hole Sewing
- Step 16 Previewing the Sewing Image
- Step 17 Transferring the Data to a Card
- Step 18 Saving the File
- Using Programmable Stitch Creator
- Creating data for the multi-position frame
- Design Center
- The Screen
- Using the Stage 2 Tool Box
- Using the Stage 3 Tool Box
- Using the Stage 4 Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- Layout & Editing
- The Screen
- Using the Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- File Menu
- Edit Menu
- Image Menu
- Input – from File
- Input – from TWAIN device
- Input – from Portrait
- Input – from Clipboard
- Output – to File
- Output – to Clipboard
- Select TWAIN device
- Modify
- Image to Stitch Wizard
- If Auto Punch is selected:
- If Photo Stitch 1 (Color) is selected:
- [Manual Color Selection]
- If Photo Stitch 1 (Mono) is selected:
- If Photo Stitch 2 (Color) is selected:
- If Photo Stitch 2 (Mono) is selected:
- If Cross Stitch is selected:
- Display Image – On/Faded/Off
- Text Menu
- Sew Menu
- Display Menu
- Option Menu
- Help Menu
- Programmable Stitch Creator
- Quick Reference
- Alphabetic Index
56
Contents Before Using Getting Started Design Center Layout & Editing
Programmable
Stitch Creator
Quick Reference Alphabetic Index
■ Create the pattern
1
The Design Page appears on the screen as shown below.
2 Create the pattern, making sure that it meets the following conditions.
NOTE:
If a pattern does not meet the conditions mentioned above, a warning will appear when continuing
to the next step.
With the
Optimize hoop change setting, the actual sewing order (including the embroidery frame installa-
tion order) is optimized as explained on page 57.
(The Optimize hoop change setting can be found on the Sew menu. The setting is turned on when a
check mark appears in front of the setting.)
◆ Explanation of a, b, and c:
a: Embroidering area when the
embroidery frame is installed at the
top installation position.
b: Embroidering area when the
embroidery frame is installed at the
middle installation position.
c: Embroidering area when the
embroidery frame is installed at the
bottom installation position.
The broken lines indicate each area.
◆
The size of one pattern must be no bigger
than 100 × 100 mm (or 130 × 180 mm).
(If the pattern is imported from Design
Center, only these size settings are
available.)
◆ Each pattern must completely fit within
one single area (a, b, or c).
1: This pattern is correct since it fits
completely within area a.
2: This pattern is correct since it fits
completely within either area b or
area c.
3: The size of this pattern is accept-
able, but its position must be cor-
rected since it does not fit
completely within any of the areas.
4: This pattern must be corrected
since it is too large.
◆ Specify the sewing order in the same
way that it is specified for a normal
frame.
a
b
c
a
b
c
4
3
2
1