Quick Start Manual
Table Of Contents
- Contents
- Before Using
- Getting Started
- Introduction
- About this Chapter
- Using the Auto Punch Function
- Using Design Center
- Using Layout & Editing
- Step 1 Starting Layout & Editing
- Step 2 Importing Embroidery Patterns from Design Center
- Step 3 Zooming In and Out
- Step 4 Moving the Embroidery Pattern
- Step 5 Adding an Oval
- Step 6 Adjusting the Size and Location of the Oval
- Step 7 Adding Text
- Step 8 Fitting the Text around the Oval
- Step 9 Moving the Oval and Text
- Step 10 Adding a Circle for Drawing the Sun
- Step 11 Selecting a Programmable Fill Stitch
- Step 12 Adding Broken Lines for Drawing the Sun Rays
- Step 13 Changing the Sewing Order of Sun and Rays
- Step 14 Adjusting the Rays
- Step 15 Setting Hole Sewing
- Step 16 Previewing the Sewing Image
- Step 17 Transferring the Data to a Card
- Step 18 Saving the File
- Using Programmable Stitch Creator
- Creating data for the multi-position frame
- Design Center
- The Screen
- Using the Stage 2 Tool Box
- Using the Stage 3 Tool Box
- Using the Stage 4 Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- Layout & Editing
- The Screen
- Using the Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- File Menu
- Edit Menu
- Image Menu
- Input – from File
- Input – from TWAIN device
- Input – from Portrait
- Input – from Clipboard
- Output – to File
- Output – to Clipboard
- Select TWAIN device
- Modify
- Image to Stitch Wizard
- If Auto Punch is selected:
- If Photo Stitch 1 (Color) is selected:
- [Manual Color Selection]
- If Photo Stitch 1 (Mono) is selected:
- If Photo Stitch 2 (Color) is selected:
- If Photo Stitch 2 (Mono) is selected:
- If Cross Stitch is selected:
- Display Image – On/Faded/Off
- Text Menu
- Sew Menu
- Display Menu
- Option Menu
- Help Menu
- Programmable Stitch Creator
- Quick Reference
- Alphabetic Index
207
Contents Before Using Getting Started Design Center Layout & Editing
Programmable
Stitch Creator
Quick Reference Alphabetic Index
Text Satin stitch
Region sewing
Density
Pull compensation
Text Fill stitch
Region sewing
Density
Pull compensation
Step pitch
Frequency
Text Programmable Fill
Region sewing
Density
Pull compensation
Programmable Fill
Pattern
Pattern size
Width
Height
Offset
Direction
Value
Direction
Manual Punch Satin
stitch
Region sewing
Density
Pull compensation
Feathered edge
Feathered side
Top side
Pattern
Max length
Bottom side
Pattern
Max length
Manual Punch Fill
stitch
Region sewing
Density
Pull compensation
Step pitch
Frequency
Feathered edge
Feathered side
Top side
Pattern
Max length
Bottom side
Pattern
Max length
Manual Punch Pro-
grammable Fill
Region sewing
Density
Pull compensation
Programmable Fill
Pattern
Pattern size
Width
Height
Offset
Direction
Value
Direction
Feathered edge
Feathered side
Top side
Pattern
Max length
Bottom side
Pattern
Max length
Under Sewing
Sets under sewing on/off. Try to use Under sewing for wide areas, in order
to prevent shrinking during stitching. Depending on the shape of the region,
however, it may not be possible to make this setting.
On: Under sewing will be done
Off: Under sewing will not be done
Density
Sets the number of lines per mm.
Range: 1 - 7 lines per mm (25 - 178 lines per inch)
Default: 4.5 lines per mm (114 lines per inch)
Direction
Type
Specifies the type of sewing direction.
Constant: Sews at a fixed angle. The angle is specified by the
Angle setting.
Variable: Varies the sewing direction according to the object
being sewn.
Angle
Specifies the sewing angle.
(If
Variable
is selected as the
Type
setting, this setting is not available.)
Range: 0 - 179 degrees
Default: 45 degrees
Pull Compensation
Lengthens the sewing region in the stitch pattern’s sewing direction to pre-
vent pattern shrinkage during sewing.
Range:0 - 2 mm (0.00 - 0.08 inch)
Default:0 mm (0.00 inch)
0˚
45˚
90˚
135˚
179˚