Quick Start Manual
Table Of Contents
- Contents
- Before Using
- Getting Started
- Introduction
- About this Chapter
- Using the Auto Punch Function
- Using Design Center
- Using Layout & Editing
- Step 1 Starting Layout & Editing
- Step 2 Importing Embroidery Patterns from Design Center
- Step 3 Zooming In and Out
- Step 4 Moving the Embroidery Pattern
- Step 5 Adding an Oval
- Step 6 Adjusting the Size and Location of the Oval
- Step 7 Adding Text
- Step 8 Fitting the Text around the Oval
- Step 9 Moving the Oval and Text
- Step 10 Adding a Circle for Drawing the Sun
- Step 11 Selecting a Programmable Fill Stitch
- Step 12 Adding Broken Lines for Drawing the Sun Rays
- Step 13 Changing the Sewing Order of Sun and Rays
- Step 14 Adjusting the Rays
- Step 15 Setting Hole Sewing
- Step 16 Previewing the Sewing Image
- Step 17 Transferring the Data to a Card
- Step 18 Saving the File
- Using Programmable Stitch Creator
- Creating data for the multi-position frame
- Design Center
- The Screen
- Using the Stage 2 Tool Box
- Using the Stage 3 Tool Box
- Using the Stage 4 Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- Layout & Editing
- The Screen
- Using the Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- File Menu
- Edit Menu
- Image Menu
- Input – from File
- Input – from TWAIN device
- Input – from Portrait
- Input – from Clipboard
- Output – to File
- Output – to Clipboard
- Select TWAIN device
- Modify
- Image to Stitch Wizard
- If Auto Punch is selected:
- If Photo Stitch 1 (Color) is selected:
- [Manual Color Selection]
- If Photo Stitch 1 (Mono) is selected:
- If Photo Stitch 2 (Color) is selected:
- If Photo Stitch 2 (Mono) is selected:
- If Cross Stitch is selected:
- Display Image – On/Faded/Off
- Text Menu
- Sew Menu
- Display Menu
- Option Menu
- Help Menu
- Programmable Stitch Creator
- Quick Reference
- Alphabetic Index
IMPORTANT INFORMATION: REGULATIONS
Federal Communications Commissions (FCC) Declaration of Conformity
(For USA Only)
Responsible Party : Brother International Corporation
100 Somerset Corporate Boulevard
Bridgewater, NJ 08807-0911 USA
declares that the product
Product Name: Brother USB Writer
Model Number: PE-DESIGN
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for Class B digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Consult the dealer or an experienced radio/TV technician for help.
– Changes or modifications not expressly approved by the manufacturer or local sales distributor
could void the user’s authority to operate the equipment.
Canadian Department of Communications Compliance Statement
(For Canada Only)
This digital apparatus does not exceed the Class B limits for radio noise emission from digital
apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”,
ICES-003 of the Department of Communications
Radio Interference
(Other than USA and Canada)
This machine complies with EN55022 (CISPR Publication 22) /Class B.