Quick Start Manual
Table Of Contents
- Contents
- Before Using
- Getting Started
- Introduction
- About this Chapter
- Using the Auto Punch Function
- Using Design Center
- Using Layout & Editing
- Step 1 Starting Layout & Editing
- Step 2 Importing Embroidery Patterns from Design Center
- Step 3 Zooming In and Out
- Step 4 Moving the Embroidery Pattern
- Step 5 Adding an Oval
- Step 6 Adjusting the Size and Location of the Oval
- Step 7 Adding Text
- Step 8 Fitting the Text around the Oval
- Step 9 Moving the Oval and Text
- Step 10 Adding a Circle for Drawing the Sun
- Step 11 Selecting a Programmable Fill Stitch
- Step 12 Adding Broken Lines for Drawing the Sun Rays
- Step 13 Changing the Sewing Order of Sun and Rays
- Step 14 Adjusting the Rays
- Step 15 Setting Hole Sewing
- Step 16 Previewing the Sewing Image
- Step 17 Transferring the Data to a Card
- Step 18 Saving the File
- Using Programmable Stitch Creator
- Creating data for the multi-position frame
- Design Center
- The Screen
- Using the Stage 2 Tool Box
- Using the Stage 3 Tool Box
- Using the Stage 4 Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- Layout & Editing
- The Screen
- Using the Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- File Menu
- Edit Menu
- Image Menu
- Input – from File
- Input – from TWAIN device
- Input – from Portrait
- Input – from Clipboard
- Output – to File
- Output – to Clipboard
- Select TWAIN device
- Modify
- Image to Stitch Wizard
- If Auto Punch is selected:
- If Photo Stitch 1 (Color) is selected:
- [Manual Color Selection]
- If Photo Stitch 1 (Mono) is selected:
- If Photo Stitch 2 (Color) is selected:
- If Photo Stitch 2 (Mono) is selected:
- If Cross Stitch is selected:
- Display Image – On/Faded/Off
- Text Menu
- Sew Menu
- Display Menu
- Option Menu
- Help Menu
- Programmable Stitch Creator
- Quick Reference
- Alphabetic Index
191
Contents Before Using Getting Started Design Center Layout & Editing
Programmable
Stitch Creator
Quick Reference Alphabetic Index
2 In the Select Mask dialog, click Next to display the Photo Stitch Parameters dialog similar to the
one shown below.
Sewing Option:
Auto Select Setting:
Auto Select:
Click this button to select from the selected thread chart the thread colors closest to the four colors
in the selected color set. The selected thread colors appear in the Use Color List mentioned below.
This button can be clicked if the settings for Auto Select Setting have been changed.
Use Color List:
Allows the selected thread colors to be checked and edited.
◆ Specify the settings for creating Photo Stitch
data.
◆ Click Previous to return to the previous dia-
log.
◆ Click Next to apply the settings to the Photo
Stitch data, and display the next dialog.
◆ Click Cancel to close this dialog.
Line Interval
Specifies the interval of parallel lines used to create embroidery data.
Range: 1.2 - 5 mm (0.05 - 0.2 inch)
Default: 2 mm (0.08 inch)
Max. Density
Specifies the maximum density for areas of the created embroidery data
sewn with the zigzag stitch. The embroidery data will be created with a
density smaller than that set here.
Range: 2.5 - 5 lines per mm (64 - 127 lines per inch)
Default: 3 lines per mm (76 lines per inch)
Thread Chart
Selects the thread chart for selecting the thread color with the Auto
Select function.
The most appropriate thread color from the selected thread chart is
selected.
A user thread chart can also be selected.
Color Set
Sets the combination of four colors used when creating embroidery
data.
The color choices are: cyan (C), magenta (M), yellow (Y), black (K), red
(R), green (G) and blue (B). Select one of the following combinations
that contains the colors most used in the image.
Color combinations: CMYK, RGBK, CRYK, BMYK
Line interval