Quick Start Manual
Table Of Contents
- Contents
- Before Using
- Getting Started
- Introduction
- About this Chapter
- Using the Auto Punch Function
- Using Design Center
- Using Layout & Editing
- Step 1 Starting Layout & Editing
- Step 2 Importing Embroidery Patterns from Design Center
- Step 3 Zooming In and Out
- Step 4 Moving the Embroidery Pattern
- Step 5 Adding an Oval
- Step 6 Adjusting the Size and Location of the Oval
- Step 7 Adding Text
- Step 8 Fitting the Text around the Oval
- Step 9 Moving the Oval and Text
- Step 10 Adding a Circle for Drawing the Sun
- Step 11 Selecting a Programmable Fill Stitch
- Step 12 Adding Broken Lines for Drawing the Sun Rays
- Step 13 Changing the Sewing Order of Sun and Rays
- Step 14 Adjusting the Rays
- Step 15 Setting Hole Sewing
- Step 16 Previewing the Sewing Image
- Step 17 Transferring the Data to a Card
- Step 18 Saving the File
- Using Programmable Stitch Creator
- Creating data for the multi-position frame
- Design Center
- The Screen
- Using the Stage 2 Tool Box
- Using the Stage 3 Tool Box
- Using the Stage 4 Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- Layout & Editing
- The Screen
- Using the Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- File Menu
- Edit Menu
- Image Menu
- Input – from File
- Input – from TWAIN device
- Input – from Portrait
- Input – from Clipboard
- Output – to File
- Output – to Clipboard
- Select TWAIN device
- Modify
- Image to Stitch Wizard
- If Auto Punch is selected:
- If Photo Stitch 1 (Color) is selected:
- [Manual Color Selection]
- If Photo Stitch 1 (Mono) is selected:
- If Photo Stitch 2 (Color) is selected:
- If Photo Stitch 2 (Mono) is selected:
- If Cross Stitch is selected:
- Display Image – On/Faded/Off
- Text Menu
- Sew Menu
- Display Menu
- Option Menu
- Help Menu
- Programmable Stitch Creator
- Quick Reference
- Alphabetic Index
182
Contents Before Using Getting Started Design Center Layout & Editing
Programmable
Stitch Creator
Quick Reference Alphabetic Index
If Auto Punch is selected:
1
After the image characteristics are analyzed, a dialog similar to the one shown below appears.
2 Select the areas that are to be sewn.
In the image on the
Result View tab, areas not set to be sewn are shown filled with a crosshatch
pattern.
Click in the areas to specify whether or not they will be sewn.
◆ Click the
Result View tab to display the
resulting analyzed image. The embroi-
dery data will be created with this
image.
◆ Click the
Original View tab to display the
original image.
◆ Drag the slider to adjust the zoom
ratio that the image is displayed in.
◆ Select the Show Outline check box to
display the outline extracted from the
analyzed image.
◆ Select the desired image-analyzing set-
tings under Analysis Parameters.
Noise reduction: Sets the level of noise
that is removed from the image.
Segmentation sensitivity: Sets the
smoothness of the extracted outline.
Outline smoothness: Sets the smooth-
ness of the extracted outline.
Max. Number of colors: Sets the num-
ber of colors used.
After the necessary settings are
selected, click Retry to re-analyze the
image. If Retry is not clicked, the new
settings are not applied.
Thread Chart: Selects the thread chart
for selecting the thread color. The most
appropriate thread color from the
selected thread chart is selected. A
user thread chart can also be selected.
These areas will not be sewn