Quick Start Manual
Table Of Contents
- Contents
- Before Using
- Getting Started
- Introduction
- About this Chapter
- Using the Auto Punch Function
- Using Design Center
- Using Layout & Editing
- Step 1 Starting Layout & Editing
- Step 2 Importing Embroidery Patterns from Design Center
- Step 3 Zooming In and Out
- Step 4 Moving the Embroidery Pattern
- Step 5 Adding an Oval
- Step 6 Adjusting the Size and Location of the Oval
- Step 7 Adding Text
- Step 8 Fitting the Text around the Oval
- Step 9 Moving the Oval and Text
- Step 10 Adding a Circle for Drawing the Sun
- Step 11 Selecting a Programmable Fill Stitch
- Step 12 Adding Broken Lines for Drawing the Sun Rays
- Step 13 Changing the Sewing Order of Sun and Rays
- Step 14 Adjusting the Rays
- Step 15 Setting Hole Sewing
- Step 16 Previewing the Sewing Image
- Step 17 Transferring the Data to a Card
- Step 18 Saving the File
- Using Programmable Stitch Creator
- Creating data for the multi-position frame
- Design Center
- The Screen
- Using the Stage 2 Tool Box
- Using the Stage 3 Tool Box
- Using the Stage 4 Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- Layout & Editing
- The Screen
- Using the Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- File Menu
- Edit Menu
- Image Menu
- Input – from File
- Input – from TWAIN device
- Input – from Portrait
- Input – from Clipboard
- Output – to File
- Output – to Clipboard
- Select TWAIN device
- Modify
- Image to Stitch Wizard
- If Auto Punch is selected:
- If Photo Stitch 1 (Color) is selected:
- [Manual Color Selection]
- If Photo Stitch 1 (Mono) is selected:
- If Photo Stitch 2 (Color) is selected:
- If Photo Stitch 2 (Mono) is selected:
- If Cross Stitch is selected:
- Display Image – On/Faded/Off
- Text Menu
- Sew Menu
- Display Menu
- Option Menu
- Help Menu
- Programmable Stitch Creator
- Quick Reference
- Alphabetic Index
172
Contents Before Using Getting Started Design Center Layout & Editing
Programmable
Stitch Creator
Quick Reference Alphabetic Index
NOTE:
The maximum value that can be entered is the largest value that will not allow the pattern to
exceed the size of the Design Page.
The minimum value is 1 mm (0.04 inch).
See also: “Select System Unit” on page 229
■ Numerical Setting-Rotate
Purpose: Rotates the selected pattern numerically.
Shortcut key: No shortcut key for this function
Toolbar: No button for this function
Operation:
1 Select one or more patterns.
2 Click Edit, then Numerical Setting, then Rotate.
The Rotate dialog appears.
NOTE:
The range of values that can be entered is between 0 and 359 degrees, in 1degree increments.
■ Center
Purpose: Moves the selected object to the center of Design Page.
Shortcut key: +
Toolbar: No button for this function
Operation:
1 Select one or more objects.
2 Click Edit, then Center.
The entire selected object moves to the center of Design Page.
NOTE:
For Letters Fit to a Path
If you select either the letters or the path only, the selected object will be moved to the center of
Design page, but the unselected object will not be moved with it.
For Objects set for Hole Sewing
When selecting an object set as part of a hole sewing pattern, the selected object will be
moved to the center of Design Page, but the unselected objects will not be moved with it.
◆ The desired rotation angle can be entered
by either typing in a value or clicking the
arrows to select the desired value.
Select 0 degree to leave the pattern
unchanged.
◆ Click
OK to confirm.
◆ Click
Preview to view the pattern rotated
the specified angle in the Design Page.
◆ Click Cancel to exit without making any
changes.
Ctrl M