Quick Start Manual
Table Of Contents
- Contents
- Before Using
- Getting Started
- Introduction
- About this Chapter
- Using the Auto Punch Function
- Using Design Center
- Using Layout & Editing
- Step 1 Starting Layout & Editing
- Step 2 Importing Embroidery Patterns from Design Center
- Step 3 Zooming In and Out
- Step 4 Moving the Embroidery Pattern
- Step 5 Adding an Oval
- Step 6 Adjusting the Size and Location of the Oval
- Step 7 Adding Text
- Step 8 Fitting the Text around the Oval
- Step 9 Moving the Oval and Text
- Step 10 Adding a Circle for Drawing the Sun
- Step 11 Selecting a Programmable Fill Stitch
- Step 12 Adding Broken Lines for Drawing the Sun Rays
- Step 13 Changing the Sewing Order of Sun and Rays
- Step 14 Adjusting the Rays
- Step 15 Setting Hole Sewing
- Step 16 Previewing the Sewing Image
- Step 17 Transferring the Data to a Card
- Step 18 Saving the File
- Using Programmable Stitch Creator
- Creating data for the multi-position frame
- Design Center
- The Screen
- Using the Stage 2 Tool Box
- Using the Stage 3 Tool Box
- Using the Stage 4 Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- Layout & Editing
- The Screen
- Using the Tool Box
- Using the Sewing Attributes Bar
- Using the Menu Bar and the Toolbar
- File Menu
- Edit Menu
- Image Menu
- Input – from File
- Input – from TWAIN device
- Input – from Portrait
- Input – from Clipboard
- Output – to File
- Output – to Clipboard
- Select TWAIN device
- Modify
- Image to Stitch Wizard
- If Auto Punch is selected:
- If Photo Stitch 1 (Color) is selected:
- [Manual Color Selection]
- If Photo Stitch 1 (Mono) is selected:
- If Photo Stitch 2 (Color) is selected:
- If Photo Stitch 2 (Mono) is selected:
- If Cross Stitch is selected:
- Display Image – On/Faded/Off
- Text Menu
- Sew Menu
- Display Menu
- Option Menu
- Help Menu
- Programmable Stitch Creator
- Quick Reference
- Alphabetic Index
157
Contents Before Using Getting Started Design Center Layout & Editing
Programmable
Stitch Creator
Quick Reference Alphabetic Index
■ Export
Purpose: Exports the data shown in the Design Page as a file of a different format (dst, hus,
exp, and pcs).
Shortcut key: No shortcut key for this function
Toolbar: No button for this function
Operation:
1 Click File, then Export.
A dialog like the one shown below appears.
NOTE:
Some patterns installed from a card cannot be exported.
■ Write to Card – Current Design
Purpose: Writes your Design Page to an original card.
Shortcut key:
Toolbar:
Operation:
1 Click File, then Write to Card, then Current Design.
This message will display.
If the card module is not connected, this message displays.
◆ Select the drive and the folder,
and then type the file name.
◆ Select the format
(DST,EXP,PCS,HUS) in which
you wish to export the file.
◆ Number of jumps for trim:
With the DST format, jump codes are
used to indicate when the thread
must be cut in order to change the
thread color. Since the number of
codes differ depending on the sewing
machine being used, this setting
allows you to select the appropriate
value. (This setting can only be speci-
fied if the DST format is selected.)
◆ If the card is not brand new, make sure
that you want to erase the data that is
already stored on the card and click OK.
◆ Click Cancel to exit.
◆ Correct the problem, then click Retry.
◆ Click
Cancel to exit.
F4