PANTONE 285 Black New_F1_brother_En_cover Operation Manual Computerized Sewing Machine GETTING READY Read before use. SEWING BASICS UTILITY STITCHES Read when additional information is required.
———————————————————————————————————————————————————— Important Safety Instructions Please read these safety instructions before attempting to use the machine. This machine is intended for household use. DANGER - To reduce the risk of electric shock: 1 Always unplug the machine from the electrical outlet immediately after using, when cleaning, when making any user servicing adjustments mentioned in this manual, or if you are leaving the machine unattended.
——————————————————————————————————————————————————— 5 Special care is required when sewing: • Always pay close attention to the needle. Do not use bent or damaged needles. • Keep fingers away from all moving parts. Special care is required around the machine needle. • Switch the sewing machine to the symbol “O” position to turn it off when making any adjustments in the needle area. • Do not use a damaged or incorrect needle plate, as it could cause the needle to break.
———————————————————————————————————————————————————— FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY IMPORTANT • In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug. • Always replace the fuse cover. Never use plugs with the fuse cover omitted. • If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead.
——————————————————————————————————————————————————— Contents Important Safety Instructions .............................................................................................. 1 Introduction ........................................................................................................................ 7 Sewing Machine Features ....................................................................................................7 Accessories..................................................
———————————————————————————————————————————————————— SEWING BASICS 49 Sewing...............................................................................................................................50 General sewing procedure .............................................................................................................................. 50 Positioning the fabric .............................................................................................................................
——————————————————————————————————————————————————— Appliqué, Patchwork and Quilt Stitching ........................................................................100 Appliqué stitching ......................................................................................................................................... 101 Patchwork (crazy quilt) stitching ................................................................................................................... 102 Piecing .....................
———————————————————————————————————————————————————— Introduction Thank you for purchasing this sewing machine. Before using this sewing machine, carefully read the “Important Safety Instructions” (page 1), and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference.
——————————————————————————————————————————————————— Accessories After opening the box, check that the following accessories are included. If any item is missing or damaged, contact your dealer. Included accessories The following items should also be included in the box. Note (For U.S.A. only) z Foot controller: Model N5V This foot controller can be used on this machine model NX-450. z The screw for the presser foot holder is available through your authorized dealer.
———————————————————————————————————————————————————— 1. 2. 3. 4. 5. 6. 7. 8. 9. 19. 10. 11. 12. 13. 14. 15. 16.* 17. 18. 20. 21. 22. 23. 24. 25. 26. 27. 28. 30. 31. 32. 33. 34. 35. 29. *75/11 2 needles 90/14 2 needles 90/14 2 needles: Ball point needle (gold colored) Part Code No.
——————————————————————————————————————————————————— Names of Machine Parts and Their Functions The names of the various parts of the sewing machine and their functions are described below. Before using the sewing machine, carefully read these descriptions to learn the names of the machine parts. Front view 2 1 D 3 4 5 C 6 B A 7 0 9 8 a Thread guide plate Pass the thread under the thread guide plate. b Thread guide cover Pass the thread behind the thread guide cover when threading the upper thread.
———————————————————————————————————————————————————— Needle and presser foot section Right-side/rear view a Buttonhole lever The buttonhole lever is used with the one-step buttonhole foot to create buttonholes. a Presser foot dial Use the presser foot dial to adjust the amount of pressure that the presser foot applies to the fabric. b Thread guide disk Pass the thread through the thread guide disk when using the needle threader to thread the needle.
——————————————————————————————————————————————————— Operation buttons The operation buttons help you to easily perform various basic sewing machine operations. a “Start/Stop” button Press the “Start/Stop” button to start or stop sewing. The machine sews at a slow speed at the beginning of sewing while the button is depressed. When sewing is stopped, the needle is lowered in the fabric. For details, refer to “Starting to sew” (page 52).
———————————————————————————————————————————————————— Operation panel The operation panel, located on the front at the right of the sewing machine, consists of the LCD (liquid crystal display) and keys for specifying various sewing settings. 1 2 3 4 5 6 9 8 0 D 7 C A E F H B G a LCD (liquid crystal display) Settings for the selected stitch and error messages for incorrect operations appear in the LCD. Use keys b and g through r, described below, to display various items and select the settings.
——————————————————————————————————————————————————— 14
1 GETTING READY The various preparations required before starting to sew are described in this chapter. T Turning the Machine On/Off ..................................................................................16 Power supply precautions ..................................................................................16 Turning on the machine .....................................................................................17 Turning off the machine .............................................
GETTING READY ———————————————————————————————————————————— Turning the Machine On/Off This section explains how to turn the sewing machine on and off. Power supply precautions Be sure to observe the following precautions concerning the power supply. WARNING ● Use only regular household electricity for the power source. Using other power sources may result in fire, electric shock, or damage to the machine.
———————————————————————————————————————————————————— Turning on the machine Prepare the included power cord. a off (the main power switch is set to “ Make sure that the sewing machine is turned ”), and then plug the power cord into the power supply jack on the right side of the machine. Insert the plug of the power cord into a b household electrical outlet. Turning off the machine When you are finished using the sewing machine, turn it off.
GETTING READY ———————————————————————————————————————————— Understanding the LCD Screens The LCD screen, located on the front at the right of the sewing machine, displays the settings for the selected stitch and error messages if operations are performed incorrectly.When the sewing machine is turned on, the LCD comes on and the following screen appears.
———————————————————————————————————————————————————— Changing the Machine Settings Various sewing machine operations and sewing settings can be changed. Changing the settings The general procedure for changing machine settings is described below. a c Press or (Stitch length keys) until the stitch or machine attribute that you wish to set is displayed. Turn on the sewing machine. 1 a Stitch length keys X The LCD comes on. Press b panel.
GETTING READY ———————————————————————————————————————————— ■ List of stitch or machine attributes The stitch or machine attributes that can be set are listed below. For details on each attribute, refer to the corresponding reference page. Attribute Icon Details Check pattern Allows combined patterns to be checked. page 121 Mirror imaging Mirror images patterns along a vertical axis. page 125 Pattern length Adjusts the length of satin stitches.
———————————————————————————————————————————————————— Adjusting the brightness of the LCD Changing the screen language The language used in the screens that are displayed can be changed to one of the many available. The brightness of the LCD can be adjusted. a Press (Settings key) in the operation panel, and then press keys) until or (Stitch length a Press (Settings key) in the operation panel, and then press or (Stitch length keys) until the language is displayed. is displayed.
GETTING READY ———————————————————————————————————————————— Winding/Installing the Bobbin This section describes how to wind the thread onto the bobbin, and then insert the bobbin thread. Bobbin precautions Be sure to observe the following precautions concerning the bobbin. CAUTION ● Only use the bobbin (part code: SA156, SFB(XA5539-151)) designed specifically for this sewing machine. Use of any other bobbin may result in injuries or damage to the machine.
———————————————————————————————————————————————————— a Turn on the sewing machine. Place the spool of thread for the bobbin onto f the spool pin. Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom. b Open the top cover. • If the spool is not positioned so that the thread unwinds correctly, the thread may become tangled around the spool pin.
GETTING READY ———————————————————————————————————————————— While holding the thread near the spool with h your right hand, as shown, pull the thread with Memo z When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the spool. your left hand, and then pass the thread behind the thread guide cover and to the front.
———————————————————————————————————————————————————— While holding the thread with your left hand, k wind the thread that was pulled out clockwise Slide the sewing speed controller to the right m to increase the bobbin winding speed and slide around the bobbin five or six times with your right hand. to left to decrease. 1 1 a Sewing speed controller Note z Make sure that the thread between the spool and the bobbin is pulled tight.
GETTING READY ———————————————————————————————————————————— q Remove the bobbin from the shaft. a Slide the bobbin cover latch to the right. 1 2 a Bobbin cover b Latch Memo z When the sewing machine is started or the handwheel is turned after winding the bobbin, the machine will make a clicking sound; this is not a malfunction. X The bobbin cover opens. b Remove the bobbin cover. Hold the bobbin with your right hand and hold c the end of the thread with your left.
———————————————————————————————————————————————————— Memo z The order that the bobbin thread should be passed through the bobbin case is indicated by marks around the bobbin case. Be sure to thread the machine as indicated. The marks around the bobbin case differ depending on the model. Note z Make sure that the thread is correctly inserted through the tension-adjusting spring of the bobbin case. If it is not inserted correctly, reinsert the thread.
GETTING READY ———————————————————————————————————————————— Upper Threading In this section, the procedures for positioning the spool for the upper thread and threading the needle are described. CAUTION ● When threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled and the needle may bend or break. Threading the upper thread Set the spool of thread on the spool pin, and then thread the machine. a Turn on the sewing machine.
———————————————————————————————————————————————————— Press (“Needle Position” button) once or c twice to raise the needle. Place the spool of thread onto the spool pin. f Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom. 1 1 a “Needle Position” button X The needle is correctly raised when the mark on the handwheel is at the top, as shown below.
GETTING READY ———————————————————————————————————————————— While holding the thread lightly with your h right hand, pull the thread with your left hand, and then pass the thread behind the thread guide cover and to the front. 1 Note z If the presser foot has been lowered and the shutter is closed, the machine cannot be threaded. Be sure to raise the presser foot and open the shutter before threading the machine.
———————————————————————————————————————————————————— Cut the thread with the thread cutter on the Threading the needle This section describes how to thread the needle. b left side of the machine. 1 1 Memo z The needle threader can be used with sewing machine needles 75/11 through 100/16. z Thread with a thickness of 130/20 or thicker cannot be used with the needle threader. z The needle threader cannot be used with the wing needle or the twin needle.
GETTING READY ———————————————————————————————————————————— Lower the needle threader lever on the left d side of the machine until it clicks, and then slowly return the lever to its original position. Raise the presser foot lever, pass the end of the e thread through the presser foot, and then pull out about 5 cm (2 inches) of thread toward the rear of the machine. 1 1 a 5 cm (2 inches) a Needle threader lever X The thread is passed through the eye of the needle.
———————————————————————————————————————————————————— Threading the needle manually (without using the needle threader) When using special thread, thread with a thickness of 130/20 or thicker, the wing needle or the twin needle which cannot be used with the needle threader, thread the needle as described below. a guide. Thread the machine to the needle bar thread Using the twin needle With the twin needle, you can sew two parallel lines of the same stitch with two different threads.
GETTING READY ———————————————————————————————————————————— Insert the extra spool pin onto the bobbin d winder shaft. Thread the upper thread for the right side in g the same way that the upper thread for the left Insert the extra spool pin so that it is perpendicular to the bobbin winder shaft. side was threaded. 1 1 a Bobbin winder shaft a Thread guide cover Swing down the spool pin so that it is • For details, refer to step h through j of “Threading the upper thread” (page 28). e horizontal.
———————————————————————————————————————————————————— k Select a stitch. • For details on selecting a stitch, refer to “Selecting stitching” (page 72). • For details on the stitches that can be sewn with the twin needle, refer to “Stitch Settings” (page 134). m Start sewing. • For details on starting to sew, refer to “Starting to sew” (page 52). X Two lines of stitching are sewn parallel to each other.
GETTING READY ———————————————————————————————————————————— Pull out about 10-15 cm (4-5 inches) of the Pulling up the bobbin thread e bobbin thread under the presser foot toward the rear of the machine. When making gathers or before free-motion quilting, first pull up the bobbin thread as described below. a Insert the bobbin into the bobbin case. • Refer to steps a through e of “Installing the bobbin” (page 26). Pass the bobbin thread through the slot. b Do not cut the thread with the cutter.
———————————————————————————————————————————————————— Replacing the Needle This section provides information on sewing machine needles. 1 Needle precautions Be sure to observe the following precautions concerning the handling of the needle. Failure to observe these precautions is extremely dangerous, for example, if the needle breaks and fragments are dispersed. Be sure to read and carefully follow the instructions below. CAUTION ● Only use home sewing machine needles.
GETTING READY ———————————————————————————————————————————— Needle types and their uses The sewing machine needle that should be used depends on the fabric and thread thickness. Refer to the following table when choosing the thread and needle appropriate for the fabric that you wish to sew.
———————————————————————————————————————————————————— Checking the needle Sewing with a bent needle is extremely dangerous since the needle may break while the machine is being operated. Before using the needle, place the flat side of the needle on a flat surface and check that the distance between the needle and the flat surface is even. Replacing the needle Replace the needle as described below.
GETTING READY ———————————————————————————————————————————— d Lower the presser foot lever. While holding the needle with your left hand, g use the screwdriver to tighten the needle clamp screw. Install the twin needle in the same way. 1 a Presser foot lever e use a screwdriver to turn the needle clamp Hold the needle with your left hand, and then screw toward you (counterclockwise) to remove the needle.
———————————————————————————————————————————————————— Replacing the Presser Foot The presser foot presses down on the fabric. Presser foot precautions Be sure to observe the following precautions concerning the presser feet. CAUTION ● Use the presser foot appropriate for the type of stitch that you wish to sew, otherwise the needle may hit the presser foot, causing the needle to bend or break. ● Only use presser feet designed specifically for this sewing machine.
GETTING READY ———————————————————————————————————————————— Press the black button at the back of the d presser foot holder. Raise the presser foot lever to check that the g presser foot is securely attached. a b Note a Black button b Presser foot holder X The presser foot holder releases the presser foot. e so that the presser foot pin is aligned with the Place a different presser foot below the holder notch in the holder.
———————————————————————————————————————————————————— Adjusting the pressure of the presser foot The presser foot pressure (the amount of pressure applied to the fabric by the presser foot) can be adjusted. For best results, increase the pressure when sewing thin fabrics, and decrease the pressure when sewing thick fabrics. a Lower the presser foot lever.
GETTING READY ———————————————————————————————————————————— Using the walking foot CAUTION With the walking foot, both pieces of fabric are fed evenly by the feed dogs and the teeth on the presser foot. This is useful when sewing fabrics that are hard to feed such as vinyl and leather and when sewing fabrics that easily slip such as velvets or when quilting. Use the screwdriver to attach the walking foot.
———————————————————————————————————————————————————— With a screwdriver, loosen the presser foot d holder screw, and then remove the walking foot. 1 a a Presser foot holder screw e Attach the presser foot holder. • For details, refer to “Removing the presser foot holder” (page 43). Memo z Only the straight stitch (with reinforcement stitching) and the zigzag stitch can be used with the walking foot. For details on the stitches, refer to “Stitch Settings” (page 134).
GETTING READY ———————————————————————————————————————————— Sewing Cylindrical or Large Pieces When sewing cylindrical or large pieces of fabric, remove the flat bed attachment. Stitching cylindrical pieces Removing the flat bed attachment makes it easier to sew cylindrical pieces such as cuffs and pant legs. a Sewing large pieces of fabric The optional wide table makes sewing large pieces of fabric easier. Pull the flat bed attachment off to the left. a table.
———————————————————————————————————————————————————— Install the wide table. c Keeping the wide table level, fully slide it into place. The lower right corner section of the wide table extends over the front section of the sewing machine bed. Install the flat bed attachment back in its f original position. Memo z With the legs folded up, the wide table can be stored attached to the hard case.
GETTING READY ———————————————————————————————————————————— 48
2 SEWING BASICS The necessary preparations for sewing are described in this chapter. Sewing.....................................................................................................................50 General sewing procedure .................................................................................50 Positioning the fabric .........................................................................................51 Starting to sew ...........................................................
SEWING BASICS ———————————————————————————————————————————— Sewing Basic sewing operations are described below. Before operating the sewing machine, read the following precautions. CAUTION ● While the machine is in operation, pay special attention to the needle location. In addition, keep your hands away from all moving parts such as the needle and handwheel, otherwise injuries may occur. ● Do not pull or push the fabric too hard while sewing, otherwise injuries may occur or the needle may break.
———————————————————————————————————————————————————— Positioning the fabric Be sure that the fabric pieces are sewn in the correct order and that the right and wrong sides of the fabric are aligned correctly. a Turn on the sewing machine. 2 The straight stitch (left needle position) is automatically selected. Press e Lower the presser foot lever. (“Needle Position” button) once or b twice to raise the needle. 1 a Presser foot lever 1 X The fabric is now positioned to be sewn.
SEWING BASICS ———————————————————————————————————————————— b Starting to sew Press (“Start/Stop” button) once. Once you are ready to start sewing, you can start the sewing machine. The sewing speed can be adjusted using either the sewing speed controller or the foot controller. 1 a “Start/Stop” button Note X The machine starts sewing. Important: z When the foot controller is plugged in, (“Start/Stop” button) cannot be used to start or stop sewing.
———————————————————————————————————————————————————— Insert the foot controller plug into its jack on b the side of the sewing machine. Once you are ready to start sewing, slowly e press down on the foot controller. Pressing down on the foot controller increases the sewing speed; releasing the pressure on the foot controller decreases the sewing speed. 1 Slower Faster • Slowly press down on the foot controller. Pressing it down hard starts sewing too quickly. a Foot controller jack Note (For U.S.A.
SEWING BASICS ———————————————————————————————————————————— After sewing 3 to 5 stitches, press Securing the stitching c (“Reverse/Reinforcement Stitch” button). Keep (“Reverse/Reinforcement Stitch” button) held down until you reach the beginning of the stitching. When sewing with the straight stitch, for example, at the end of an opening or where seams do not overlap, use reverse stitching or reinforcement stitching to secure the end of the thread.
———————————————————————————————————————————————————— After 3 to 5 reverse stitches have been sewn, (“Reverse/Reinforcement Stitch” button). g release h Cutting the thread X The machine stops sewing. When you have finished sewing, cut the threads. The threads can be cut in either of two ways. Press ■ Using (“Start/Stop” button), or press down on the foot controller. At this time, if (“Start/Stop” button) is held down, the machine sews at a slow speed.
SEWING BASICS ———————————————————————————————————————————— ■ Using the manual thread cutter When sewing with thread thicker than #30, nylon or metallic threads, or other special threads, use the thread cutter on the side of the machine to cut the threads. When you wish to finish the stitching and the a sewing machine is stopped, press (“Needle Position” button) once to raise the needle. 1 a “Needle Position” button X The needle is raised. b Raise the presser foot lever.
———————————————————————————————————————————————————— Adjusting the Thread Tension The tensions of the upper thread and of the bobbin thread (thread tension) should be adjusted so that they are equal. Changing the tension of the upper thread Turn the thread tension dial to the left to loosen the upper thread. You may need to change the thread tension, depending on the fabric and thread being used. ■ Correct thread tension The upper thread and the bobbin thread should cross near the center of the fabric.
SEWING BASICS ———————————————————————————————————————————— Adjusting the Stitch Width and Length The zigzag width (pattern width) and stitch length of utility stitches can be adjusted. Normally, when a stitch is selected, the appropriate width and length are automatically selected. For details on the range of values within which the width and length can be set, refer to “Stitch Settings” (page 134).
———————————————————————————————————————————————————— Adjusting the stitch length The stitch length can be adjusted to make the stitch longer or shorter. a c To make the stitch length shorter, press (Stitch length key). To make the stitch length longer, press (Stitch length key). Turn on the sewing machine. X The stitch length is changed. X The LCD comes on. b Select a stitch. X A screen containing settings for the selected stitch appears.
SEWING BASICS ———————————————————————————————————————————— Useful Functions Functions useful in improving sewing efficiency are described below. Changing the needle stop position When the sewing machine is purchased, it is set to leave the needle lowered in the fabric when sewing is stopped. However, the machine can be set to instead leave the needle raised when sewing is stopped. a Turn on the sewing machine.
———————————————————————————————————————————————————— c Press (Automatic reverse/reinforcement stitch key). This step is not necessary if a stitch such as those for sewing buttonholes and bar tacks is selected where reinforcement stitches are automatically sewn. e After reaching the end of the stitching, press (“Reverse/Reinforcement Stitch” button) once.
SEWING BASICS ———————————————————————————————————————————— Automatically cutting the thread Position the fabric under the presser foot, and (“Start/Stop” button) once. d then press The sewing machine can be set to automatically cut the threads at the end of the stitching. This is called “programmed thread-cutting”. If programmed threadcutting is set, automatic reverse/reinforcement stitching is also set. This setting is convenient if a stitch for sewing buttonholes or bar tacks is selected.
———————————————————————————————————————————————————— b Saving stitch settings Adjusted stitch width and length settings can be saved so that they will be specified each time the stitch is selected. The various settings can be saved for each utility stitch. a Press (Manual memory key). X “Saving...” appears while the settings for the stitch width and stitch length are being saved. X After the settings for the stitch width and stitch length are saved, the initial stitch screen appears again.
SEWING BASICS ———————————————————————————————————————————— Hands-free raising and lowering of the presser foot Using the knee lifter, you can raise and lower the presser foot with your knee, leaving both hands free to handle the fabric. ■ Using the knee lifter a Stop the sewing machine. • Do not use the knee lifter while the sewing machine is operating. With your knee, press the knee lifter to the b right. Keep the knee lifter pressed to the right.
———————————————————————————————————————————————————— Useful Sewing Tips Various ways to achieve better results for your sewing projects are described below. Refer to these tips when sewing your project. Trial sewing After you have set up the machine with the thread and needle appropriate for the type of fabric being sewn, the machine automatically sets the thread tension and stitch length and width for the stitch that is selected.
SEWING BASICS ———————————————————————————————————————————— Release the button. The foot will lock in place c level with the seam, allowing the fabric to Sewing thick fabrics feed. ■ If the fabric does not fit under the presser foot If the fabric does not fit easily under the presser foot, raise the presser foot lever even higher to bring the presser foot to its highest position. X Once the trouble spot has been passed, the foot will return to its normal position.
———————————————————————————————————————————————————— Sewing leathers or vinyl fabrics When sewing the fabrics that may stick to the presser foot such as leathers or coated fabrics, change the presser foot to the non stick foot. ■ Aligning the fabric with a needle plate marking The markings on the needle plate show the distance from the needle position of a seam sewn with the straight stitch (left needle position). Sew while keeping the edge of the fabric aligned with a marking in the needle plate.
SEWING BASICS 68 ————————————————————————————————————————————
3 UTILITY STITCHES The various stitches and their applications are described in this chapter. Selecting Stitching ...............................70 Selecting stitch types and patterns....... 70 Selecting stitching .......................... 72 Overcasting Stitches............................ 76 Sewing overcasting stitches using overcasting foot “G” ............. 76 Sewing overcasting stitches using zigzag foot “J” ......................77 Sewing overcasting stitches using the optional side cutter ........
UTILITY STITCHES ——————————————————————————————————————————— Selecting Stitching You can select any of the various types of stitching available. Selecting stitch types and patterns A stitch can be selected from the following types available. Stitch patterns can be selected through either direct select (by pressing the key for a specific stitch) or number selection (by entering the number for the stitch pattern). For details on the types of stitches available, refer to “Stitch Settings” (page 134).
———————————————————————————————————————————————————— Decorative stitches Character stitches There are two decorative stitch modes: decorative There are three character stitch modes: Gothic stitch 1 mode font mode and decorative stitch 2 mode . If , Script font mode outline style mode (Decorative stitch key) is pressed once, decorative stitch 1 mode is selected. If If and . (Character stitch key) is pressed once, Gothic font mode is selected.
UTILITY STITCHES ——————————————————————————————————————————— Selecting stitching Using the operation panel keys, select the desired stitch. Ten of the most often used utility stitches can quickly be selected with the numeric keys. Right after turning the power on, the straight stitch (left needle position) is selected. The machine can also be set to select the straight stitch (center needle position). For details, refer to “Changing the settings” (page 19).
———————————————————————————————————————————————————— ■ With number selection Character stitches There are three modes of stitches that can be selected by number: utility stitch mode decorative stitch mode mode : Gothic font , 55 letter, symbol and numbers are available. and character stitch When . In addition, there are two decorative stitch modes : decorative stitch 1 mode decorative stitch 2 mode 55 letter, symbol and numbers are available.
UTILITY STITCHES ——————————————————————————————————————————— Use the numeric keys to type in the two-digit b number for the desired stitch. For stitches 01 through 09, the stitch can also ■ To select a different stitch Check the icon in the lower-left corner of the screen for the current mode. be selected by using the numeric keys to type in a one-digit number, then pressing (OK key). X After the entered number appears in the center of the screen, the stitch is selected.
———————————————————————————————————————————————————— • To erase the stitch and select a different one, press (OK key), and then change the stitch mode. • To stop the current stitch from being erased, press (Cancel/clear key) to return to the previous screen. Memo z After changing stitch settings such as the stitch length and width or after combining patterns, the stitch pattern can be saved with its current settings. For details, refer to “Saving patterns” (page 126).
UTILITY STITCHES ——————————————————————————————————————————— Overcasting Stitches Sew overcasting stitches along the edges of cut fabric to prevent fabric from fraying. Fifteen stitches are available for overcasting. The procedure for sewing overcasting stitch is explained according to the presser foot that is used. Sewing overcasting stitches using overcasting foot “G” Three stitches can be used to sew overcasting with overcasting foot “G”.
———————————————————————————————————————————————————— Sewing overcasting stitches using zigzag foot “J” Seven stitches can be used to sew overcasting stitches with zigzag foot “J”.
UTILITY STITCHES ——————————————————————————————————————————— Sewing overcasting stitches using the optional side cutter Using the side cutter, seam allowances can be finished while the edge of the fabric is cut off. Five stitches can be used to sew overcasting stitches with the side cutter. Pattern Stitch Name Overcasting stitch Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual 63 Sewing straight stitches while cutting the fabric 0.0 (0) 0.0–2.
———————————————————————————————————————————————————— Raise the presser foot lever to check that the f side cutter is securely attached. Position the fabric in the side cutter. j The cut in the fabric should be positioned over the guide plate of the side cutter. Pass the upper thread under the side cutter, g and then pull it out toward the rear of the sewing machine. a a Guide plate • If the fabric is not positioned correctly, the fabric will not be cut.
UTILITY STITCHES ——————————————————————————————————————————— Basic Stitching Straight stitches are used for sewing plain seams. Five stitches are available for basic stitching. Stitch Name Basting stitch Pattern Numeric Key 06 – 01 Straight stitch (left needle position) Straight stitch (center needle position) Triple stretch stitch 02 – 03 04 Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Temporarily securing 0.0 (0) 0.0–7.
———————————————————————————————————————————————————— Basic stitching a Baste or pin together the fabric pieces. b Attach zigzag foot “J”. ■ Changing the needle position The needle position used as the baseline is different for the straight stitch (left needle position) and the straight stitch (center needle position). 1 2 J • For details, refer to “Replacing the presser foot” (page 41). c Select a stitch. • For details, refer to “Selecting stitching” (page 72).
UTILITY STITCHES ——————————————————————————————————————————— Blind Hem Stitching Secure the bottoms of skirts and pants with a blind hem. Two stitches are available for blind hem stitching. Stitch Name Pattern Numeric Key 17 Blind hem stitch 18 – Stitch Width [mm (inch)] Application Stitch Length [mm (inch)] Auto Manual Auto Manual Blind hem stitching on medium weight fabrics 00 (0) 3← – 3→ 2.0 (1/16) 1.0–3.5 (1/16–1/8) Blind hem stitching on stretch fabrics 00 (0) 3← – 3→ 2.
———————————————————————————————————————————————————— ■ If the needle does not catch the hem fold The needle is too far to the right. Press (of the Stitch width keys) to increase the stitch width so that the needle slightly catches the fold of the hem. Adjust the stitch width until the needle slightly f catches the fold of the hem.
UTILITY STITCHES ——————————————————————————————————————————— Buttonhole Stitching/Button Sewing Buttonholes can be sewn and buttons can be sewn on. Eleven stitches are available for sewing one-step buttonholes and one stitch for sewing on buttons. Stitch Name Pattern Numeric Key 48 49 50 52 53 54 55 56 57 Buttonsewing stitch 84 61 Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual – Horizontal buttonholes on thin and medium weight fabrics 5.0 (3/16) 3.0–5.
———————————————————————————————————————————————————— Buttonhole sewing The maximum buttonhole length is about 28 mm (1-1/8 inches) (diameter + thickness of the button). Buttonholes are sewn from the front of the presser foot to the back, as shown below. 1 1 3 1 1 a Reinforcement stitching The names of parts of buttonhole foot “A”, which is used for sewing buttonholes, are indicated below. Use chalk to mark on the fabric the position a and length of the buttonhole.
UTILITY STITCHES ——————————————————————————————————————————— ■ If the button does not fit in the button guide plate Add together the diameter and thickness of the button, and then set the button guide plate to the calculated length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).) Position the fabric with the front end of the e buttonhole mark aligned with the red marks on the sides of the buttonhole foot, and then lower the presser foot lever.
———————————————————————————————————————————————————— Gently hold the end of the upper thread in g your left hand, and then start sewing. 1 a Eyelet punch X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. Cut the threads, raise the presser foot lever, h and then remove the fabric. Raise the buttonhole lever to its original i position.
UTILITY STITCHES ——————————————————————————————————————————— ■ Changing the stitch width Adjust the stitch width. – b Attach buttonhole foot “A”. c Select stitch 52 + • For details, refer to “Replacing the presser foot” (page 41). or 53 . Adjust the stitch width to the thickness of the d gimp thread. Lower the presser foot lever and the e buttonhole lever, and then start sewing. When sewing is finished, gently pull the gimp f thread to remove any slack.
———————————————————————————————————————————————————— Adjust the stitch width so that it is the same as e the distance between the holes in the button. Button sewing Buttons can be sewn on with the sewing machine. Buttons with 2 or with 4 holes can be attached. f Place the button into button-sewing foot “M”. Measure the distance between the holes in the a button to be attached.
UTILITY STITCHES ——————————————————————————————————————————— Start sewing. h Set the sewing speed controller to the left (so that the speed will be slow). ■ Attaching a shank to a button To sew the button with a shank, attach the button with space between it and the fabric, and then wind the thread by hand. This attaches the button securely. Place the button into button-sewing foot “M”, a and then pull the shank lever toward you.
———————————————————————————————————————————————————— Zipper Insertion A zipper can be sewn in place. Stitch Name Straight stitch (center needle position) Pattern Numeric Key Application Attaching zippers Sewing concealed seams and pintucks 03 Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual 3.5 (1/8) 0.0–7.0 (0–1/4) 2.5 (3/32) 0.2–5.0 (1/64–3/16) Presser Foot I There are many methods for inserting zippers.
UTILITY STITCHES ——————————————————————————————————————————— Attach the presser foot holder to the right pin e of zipper foot “I”. g Topstitch around the zipper. 1 1 I 3 2 2 4 a Pin on the right side b Needle drop point • For details, refer to “Replacing the presser foot” (page 41). f Select stitch 03 . • For details, refer to “Selecting stitching” (page 72).
———————————————————————————————————————————————————— Press open the seam allowance from the Inserting a side zipper c wrong side of the fabric. Stitching is sewn on only one piece of fabric. Use this type of zipper application for side openings and back openings. 1 2 1 a Wrong side of fabric Press the seam allowance so that the right side d (the side that will not be stitched) has an extra 3 mm (1/8 inch).
UTILITY STITCHES g ——————————————————————————————————————————— Select stitch 03 . Close the zipper, turn over the fabric, and then j baste the other side of the zipper to the fabric. • For details, refer to “Selecting stitching” (page 72). CAUTION ● When using zipper foot “I”, be sure to select the straight stitch (center needle position), and slowly turn the handwheel toward you (counterclockwise) to check that the needle does not touch the presser foot.
———————————————————————————————————————————————————— When you are about 5 cm (2 inches) from the m end of the zipper, stop the sewing machine with the needle lowered (in the fabric), raise the presser foot lever, and then open the zipper and continue sewing. n Remove the basting stitching.
UTILITY STITCHES ——————————————————————————————————————————— Zipper/piping Insertion A zipper and piping can be sewn in place. Stitch Name Straight stitch (left needle position) Pattern Numeric Key Application Attaching zippers Sewing concealed seams and piping 01 Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual 0.0 (0) 0.0–7.0 (0–1/4) 2.5 (3/32) 0.2–5.0 (1/64–3/16) Presser Foot There are many methods for inserting zippers and pipings.
———————————————————————————————————————————————————— Securely tighten the positioning screw with a g screwdriver. Inserting a piping Place the piping between two fabric pieces a turned inside out, as shown below. 1 1 2 3 a Positioning screw h a Fabric b Piping c Fabric Topstitch around the zipper. Refer to the steps of attaching the adjustable 1 b zipper/piping foot (page 96). 3 2 c Sew along the piping. d After sewing, turn fabric pieces.
UTILITY STITCHES ——————————————————————————————————————————— Sewing Stretch Fabrics and Elastic Tape Stretch fabrics can be sewn and elastic tape can be attached. Stitch Name Stretch stitch Pattern Numeric Key 05 2-point zigzag stitch 09 3-point zigzag stitch 10 Elasticattaching stitch Application Stretch fabrics – Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual 1.0 (1/16) 1.0–3.0 (1/16–1/8) 2.5 (3/32) 1.0–4.0 (1/16–3/16) 5.0 (3/16) 1.5–7.0 (1/16–1/4) 1.
———————————————————————————————————————————————————— b Attach zigzag foot “J”. J • For details, refer to “Replacing the presser foot” (page 41). c Select a stitch. • For details, refer to “Selecting stitching” (page 72). Sew the elastic tape to the fabric while d stretching the tape so that it is the same length as the fabric. While pulling the fabric behind the presser foot with your left hand, pull the fabric at the pin nearest the front of the presser foot with your right hand.
UTILITY STITCHES ——————————————————————————————————————————— Appliqué, Patchwork and Quilt Stitching The stitches that can be used for sewing appliqués, patchwork and quilts are described below. Stitch Name Pattern Numeric Key Appliqué stitch 25 21 Auto Manual Attaching appliqués (center baseline/ reverse stitching) 3.5 (1/8) 0.0–7.0 (0–1/4) 1.4 (1/16) 0.0–4.0 (0–3/16) – Appliqué quilting, free-motion quilting, satin stitching 3.5 (1/8) 0.0–7.0 (0–1/4) 1.4 (1/16) 0.0–4.
———————————————————————————————————————————————————— d Appliqué stitching Attach the open toe foot. For best results, use the included open toe foot. a allowance of between 3 and 5 mm (1/8 and Cut out the appliqué, leaving a seam • For details, refer to “Replacing the presser foot” (page 41). 3/16 inch). 1 e Select a stitch. • For details, refer to “Selecting stitching” (page 72).
UTILITY STITCHES ——————————————————————————————————————————— Patchwork (crazy quilt) stitching Fold the edge of the top piece of fabric and a place it over the lower piece. Sew the two pieces of fabric together so the b pattern spans over both pieces. Piecing Sewing together two pieces of fabric is called “piecing”. The fabric pieces should be cut with a 6.5 mm (1/4 inch) seam allowance. Sew a piecing straight stitch 6.5 mm (1/4 inch) from either the right side or the left side of the presser foot.
———————————————————————————————————————————————————— ■ For a seam allowance on the left side Align the left side of the presser foot with the edge of the fabric, and sew using stitch 22 . 1 a 6.5 mm (1/4 inch) Memo z To change the width of the seam allowance (the needle position), adjust the stitch width. Quilting Sandwiching batting between the top and bottom layers of fabric is called “quilting”. Quilts can easily be sewn using the walking foot and the optional quilting guide.
UTILITY STITCHES ——————————————————————————————————————————— ■ Using the optional quilting guide Use the quilting guide to sew parallel stitches that are equally spaced. Free-motion quilting With free-motion quilting, lower the feed dogs (using the drop feed lever) so that the fabric can be moved freely in any direction. The quilting foot is needed for free-motion quilting. Insert the stem of the quilting guide into the a hole at the rear of the walking foot or presser foot holder.
———————————————————————————————————————————————————— Slide the drop feed lever, located at the rear of (to the left as seen from the rear of the machine). d the machine on the base, to a a Feed dog position switch (as seen from the rear of the machine) Satin stitching using the sewing speed controller A decorative stitch can be sewn by changing the stitch width of a satin stitch.
UTILITY STITCHES e Press ——————————————————————————————————————————— or (Stitch width keys) to select . To return to width keys). , press or When you are finished sewing, set the stitch i width control setting back to OFF. (Stitch Memo z Although the stitching result differs depending on the type of fabric being sewn and the thickness of the thread being used, for best results, adjust the stitch length to between 0.3 and 0.5 mm (1/64 and 1/32 inch).
———————————————————————————————————————————————————— Reinforcement Stitching Reinforce points that will be subject to strain, such as sleeve holes, inseams and pocket corners. Stitch Name Pattern Numeric Key Triple stretch stitch 04 Bar tack stitch 60 Reinforcing the seams of sleeves and inseams 58 Darning stitch Application 59 Stitch Length [mm (inch)] Auto Manual Auto Manual 0.0 (0) 0.0–7.0 (0–1/4) 2.5 (3/32) 1.5–4.0 (1/16–3/16) – Reinforcing the ends 2.
UTILITY STITCHES ——————————————————————————————————————————— b Attach buttonhole foot “A”. c Select stitch 60 Pull down the buttonhole lever as far as • For details, refer to “Replacing the presser foot” (page 41). e possible. . • For details, refer to “Selecting stitching” (page 72). Position the fabric so that the opening of the d pocket faces toward you, and then lower the presser foot lever so that the needle drops 2 mm (1/16 inch) in front of the pocket opening.
———————————————————————————————————————————————————— Darning Fabric that has been torn can be darned. Darning is sewn as shown below. 1 3 1 a Reinforcement stitching Determine the desired length of the darning. a Set the button guide plate on buttonhole foot “A” to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).) Position the fabric so that the needle is 2 mm d (1/16 inch) in front of the area to be darned, and then lower the presser foot lever.
UTILITY STITCHES ——————————————————————————————————————————— Pull down the buttonhole lever as far as e possible. a a Buttonhole lever The buttonhole lever is positioned behind the bracket on the buttonhole foot. 1 2 a Buttonhole lever b Bracket Gently hold the end of the upper thread in f your left hand, and then start sewing. X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. Cut the threads, raise the presser foot lever, g and then remove the fabric.
———————————————————————————————————————————————————— Eyelet Stitching Eyelets, such as those on belts, can be sewn. Three sizes of eyelets are possible: 7 mm, 6 mm and 5 mm (1/4, 15/64 and 3/16 inch). Pattern Stitch Name Eyelet stitch a Application 62 Sewing eyelets, for example, on belts Attach monogramming foot “N”. Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual 7.0 (1/4) 7.0, 6.0 or 5.0 (1/4, 15/64 or 3/16) – – e Presser Foot N Start sewing.
UTILITY STITCHES ——————————————————————————————————————————— Decorative Stitching Various decorative stitches can be sewn with this sewing machine.
———————————————————————————————————————————————————— Pattern Stitch Name Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual 6.0 (15/64) 1.5–7.0 (1/16–1/4) 1.6 1.0–4.0 (1/16) (1/16–3/16) 5.0 (3/16) 1.5–7.0 (1/16–1/4) 1.6 1.0–4.0 (1/16) (1/16–3/16) 35 4.0 (3/16) 0.0–7.0 (0–1/4) 3.0 (1/8) Rick-rack stitch 36 4.0 (3/16) 0.0–7.0 (0–1/4) 2.5 1.0–4.0 (3/32) (1/16–3/16) Decorative stitch 37 5.5 (7/32) 0.0–7.0 (0–1/4) 1.6 1.0–4.
UTILITY STITCHES ——————————————————————————————————————————— Scallop stitching The wave-shaped repeating pattern that looks like shells is called “scalloping”. It is used on the collars of blouses and to decorate the edges of handkerchiefs. a Attach monogramming foot “N”. Smocking The decorative stitch created by stitching or embroidering over gathers is called “smocking”. It is used to decorate the front of blouses or cuffs. The smocking stitch adds texture and elasticity to fabric.
———————————————————————————————————————————————————— e Select stitch 31 , 32 or 33 . • For details, refer to “Selecting stitching” (page 72). f Stitch between the straight stitches. c Select stitch 20 , and then increase the thread tension. • For details, refer to “Selecting stitching” (page 72). d slightly off the edge of the fabric. Sew while making sure that the needle drops 1 g 3 Pull out the threads for the straight stitches.
UTILITY STITCHES ——————————————————————————————————————————— Joining Heirloom stitching Decorative bridging stitches can be sewn over the seam allowance of joined fabrics. This is used when making a crazy quilt. a Attach zigzag foot “J”. When sewing with the wing needle, the needle holes are enlarged, creating a lace-like decorative stitch. This is used to decorate hems and tablecloths on thin or medium weight fabrics in addition to plain weave fabrics.
———————————————————————————————————————————————————— d Start sewing. c Select stitch 39 . • For details, refer to “Selecting stitching” (page 72). CAUTION ● Select a stitch width of 6.0 mm (15/64 inch) or less, otherwise the needle may bend or break. ● After adjusting the stitch width, slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break.
UTILITY STITCHES g Press or ——————————————————————————————————————————— (Stitch width keys) to select ■ Drawnwork (Example 2) . To return to width keys). , press or (Stitch Pull out several threads from two sections of a the fabric, separated by an unfrayed section of about 4 mm (3/16 inch). X The pattern is flipped. Press h key). (OK key) or (Cancel/clear 1 X The initial stitch screen appears again. a 4 mm (3/16 inch) b Attach monogramming foot “N”.
———————————————————————————————————————————————————— Sewing the Various Built-In Decorative Patterns Satin stitches, cross-stitches and decorative satin stitches can be sewn. All are sewn with monogramming foot “N”. c Sewing beautiful patterns Start sewing. In order to sew the patterns correctly, the following must be considered.
UTILITY STITCHES ——————————————————————————————————————————— c Combining patterns Repeat steps b . Multiple patterns can be combined and sewn together. Decorative stitches and character stitches (stitches selected with and After all of the desired patterns are selected, d start sewing. ) can be combined. 1 However, utility stitches (stitches selected with and a ) cannot be combined. Select the first pattern. a Sewing direction X The first pattern is selected and appears in the LCD.
———————————————————————————————————————————————————— Press To repeatedly sew the combined pattern, follow the procedure described below. a (OK key) or e key). Repeat sewing patterns (Cancel/clear X The initial stitch screen appears again, and the machine is set to repeatedly sew the selected pattern. Select the pattern. 1 2 • For details, refer to “Combining patterns” (page 120). Press b panel. (Settings key) in the operation X The settings screen appears.
UTILITY STITCHES b Press or ——————————————————————————————————————————— (Stitch length keys) until Changing the pattern size is displayed. The size of character stitches in the Gothic font ( selected with with ) and outline style ( selected ) can be switched between large and small. However, the size of other patterns cannot be changed. For details on the stitch patterns whose size X The screen for checking the pattern appears. can be changed, refer to “Other stitches” (page 138).
———————————————————————————————————————————————————— d Press or (Stitch width keys) until the Changing the stitch density desired size is selected. Select for the small size or select for the large size. If a decorative satin stitch has been selected, the stitch density can be changed. a Select a decorative satin stitch (No. 53–62 of , selected with b panel. Press ). (Settings key) in the operation X The settings screen appears. X The pattern size is changed. e key).
UTILITY STITCHES d Press ——————————————————————————————————————————— or (Stitch width keys) until the desired density is selected. Select for sparse stitching or select c Press or (Stitch length keys) until is displayed. for compact stitching. X The screen for changing the length of a satin stitch appears. e Press (OK key) or (Cancel/clear key). X The initial stitch screen appears again, and the stitching density is changed.
———————————————————————————————————————————————————— Press e key). Mirror imaging the pattern Select a stitch. b Press (Cancel/clear X The initial stitch screen appears again. The pattern can be mirror imaged along a vertical axis. a (OK key) or 1 2 (Settings key) in the operation panel. X The settings screen appears. a Normal b Mirror-imaged Press z Some of the utility stitches, most of the decorative stitches, and all of the character stitches can be mirror imaged.
UTILITY STITCHES ——————————————————————————————————————————— Check the contents, and then press Saving patterns d key). (OK The contents saved in the selected pocket are overwritten. Combined patterns can be saved for later use. Since saved patterns are not lost after the sewing machine is turned off, they can be retrieved at any time. This is convenient for patterns, such as names, that will be used often. Utility stitches can also be saved. Up to ten patterns can be saved. X “Saving...
———————————————————————————————————————————————————— Press the numeric key (0 through 9) for the b pocket where the pattern is saved. c Start sewing. X The saved contents of the pocket for the selected number are retrieved. X The pattern for making the adjustment is sewn. • If nothing was saved in the selected pocket, a beep is sounded, and the screen displayed before the numeric key was pressed appears again. X The sewing machine stops after it has finished sewing the pattern.
UTILITY STITCHES g Press or ——————————————————————————————————————————— (Stitch width keys). X Make the necessary adjustments according to how the pattern is sewn. Press (Stitch width key) to increase the adjustment setting. Press (Stitch width key) to decrease the adjustment setting. Start sewing again, and then check the pattern. h Continue adjusting the pattern until it is sewn correctly. i When the pattern is sewn correctly, press (OK key) or (Cancel/clear key).
———————————————————————————————————————————————————— Designing a Pattern With the My Custom Stitch function, you can sew stitch patterns that you design yourself. Drawing a sketch of the pattern Mark the points in the pattern that are c positioned at intersections in the grid, and then link those points with a continuous straight line. Prepare a grid sheet set. a set. Draw a sketch of the pattern on the grid sheet 3 d Determine the sewing order.
UTILITY STITCHES ——————————————————————————————————————————— Check the grid sheet set, and specify the d coordinates of the first point. Entering the pattern data Press a and (Stitch width keys) to select the horizontal coordinate and press Follow the pattern drawn on the grid sheet and program the pattern into the sewing machine. and (Stitch length keys) to select the vertical coordinate, and then press Attach monogramming foot “N”. (OK key).
———————————————————————————————————————————————————— g Select , and then press (OK key). Specify the various stitching settings, such as j reverse/reinforcement stitching, in the same way as with other stitches. • If you make a mistake while specifying a point, press (Cancel/clear key) so that the point changes from to • With this screen displayed, pressing , and (Cancel/clear key) displays the screen where then move (edit) the position of the point.
UTILITY STITCHES ——————————————————————————————————————————— Examples of designs Enter each of the points indicated in the table to sew the sample stitch.
4 APPENDIX The various maintenance and troubleshooting procedures are described in this chapter. Stitch Settings........................................................................................................134 Utility stitches ..................................................................................................134 Other stitches...................................................................................................138 Care and Maintenance .................................
APPENDIX —————————————————————————————————————————————— Stitch Settings Applications, stitch lengths and widths and whether the twin needle can be used are listed for utility stitches in the following table. Left Center Triple stretch stitch Stretch stitch Right Zigzag stitch Center Basting stitch 2-point zigzag stitch 3-point zigzag stitch Walking Foot No 0.0–7.0 (0–1/4) 2.5 0.2–5.0 Yes (3/32) (1/64–3/16) (J) J Basic stitching and sewing gathers or pintucks 0.0 (0) 0.0–7.0 (0–1/4) 2.5 0.
Overcasting stitch Appliqué stitch Shell tuck stitch Straight stitch that looks hand-sewn (for quilting) Satin scallop stitch Walking Foot 4.0 1.0–4.0 Yes Reinforcement + No (3/16) (1/16–3/16) (J) Reinforcement thread-cutting 3← – 3→ 2.0 (1/16) 1.0–3.5 (1/16–1/8) No Reinforcement Reinforcement + No thread-cutting R Blind hem stitching on stretch fabrics 00 (0) 3← – 3→ 2.0 (1/16) 1.0–3.5 (1/16–1/8) No Reinforcement Reinforcement + No thread-cutting J Appliqué stitching 3.5 (1/8) 2.5–7.
Elasticattaching stitch Ladder stitch Rick-rack stitch Decorative stitch Serpentine stitch J Fagoting and decorative stitching 5.0 (3/16) 0.0–7.0 (0–1/4) 2.5 1.0–4.0 Yes Reinforcement + Reinforcement No (3/32) (1/16–3/16) (J) thread-cutting J Fagoting and decorative stitching 5.0 (3/16) 2.5–7.0 (3/32–1/4) 2.5 1.0–4.0 Yes Reinforcement + Reinforcement No (3/32) (1/16–3/16) (J) thread-cutting J Attaching elastic to stretch fabrics 4.0 (3/16) 0.0–7.0 (0–1/4) 1.0 0.2–4.
5.0 (3/16) 3.0–5.0 (1/8–3/16) 0.4 0.2–1.0 Automatic No (1/64) (1/64–1/16) reinforcement Thread-cutting No Secured buttonholes for A fabrics that have backings 5.0 (3/16) 3.0–5.0 (1/8–3/16) 0.4 0.2–1.0 Automatic (1/64) (1/64–1/16) No reinforcement Thread-cutting No A Buttonholes for stretch or 6.0 (15/54) knit fabrics 3.0–6.0 (1/8– 15/ 64) 1.0 0.5–2.0 Automatic No (1/16) (1/32–1/16) reinforcement Thread-cutting No A Buttonholes for stretch fabrics 6.0 (15/54) 3.0–6.0 (1/8– 15/ 64) 1.
APPENDIX —————————————————————————————————————————————— 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 Decorative stitches 21 22 23 24 25 26 27 28 29 30 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Left/Right Flipping 03 Adjustable Pattern Length/width 02 Adjustable Stitching Density 01 Pattern Size Stitch Type Twin Needle Pattern Presser Foot Other stitches N No Large No Yes Yes N Yes (J) Large No Yes Yes N No
01 02 03 04 05 06 07 11 12 13 16 17 18* 20 21 22 23 24 25 26 27* 28 08 Utility decorative stitches 09 14 15 Left/Right Flipping Adjustable Pattern Length/width J** Yes (*Not possible) (J) G** No R** No No N No (*Not impossible) Yes Pattern Size Twin Needle Stitch Type Presser Foot Pattern Adjustable Stitching Density ———————————————————————————————————————————————————— Yes 29 10 19* 30* 31 32 33 34 35 36 37 No No Yes No 38 39 ** Use monogramming foo
06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 Character stitches (Gothic font) 31 22 23 24 25 26 27 28 29 30 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 N Large, No Small Left/Right Flipping 05 No No Yes Left/Right Flipping 04 Adjustable Pattern Length/width 03 Adjustable Pattern Length/width 02 Adjustable Stitching Density 01 Adjustable Stitching Density Stitch Type Pattern Size Pattern Twin Needle ——————————
04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 N Large, No Small Left/Right Flipping 03 Adjustable Pattern Length/width 02 Adjustable Stitching Density Character stitches (Outline style) 01 Pattern Size Stitch Type Twin Needle Pattern Presser Foot ———————————————————————————————————————————————————— No No Yes 4 Memo z To select (
APPENDIX —————————————————————————————————————————————— Care and Maintenance Simple sewing machine maintenance operations are described below. Remove the needle plate cover. Cleaning the machine surface d The needle plate cover is removed differently depending on the model. If the surface of the machine is dirty, lightly soak a cloth in neutral detergent, squeeze it out firmly, and then wipe the surface of the machine. After cleaning it once with a wet cloth, wipe it again with a dry cloth.
———————————————————————————————————————————————————— Remove the bobbin case. e Grasp the bobbin case, and then pull it out. Install the needle plate cover. h The needle plate cover is installed differently depending on the model. ■ If there is a screw in the needle plate cover Insert the tabs on the needle plate cover into a the needle plate, and then slide the cover back on.
APPENDIX —————————————————————————————————————————————— Troubleshooting If the machine stops operating correctly, check the following possible problems before requesting service. If the problem persists, contact your dealer or the nearest authorized service center. Symptom The sewing machine does not operate. Probable Cause Remedy The machine is not turned on. Turn on the machine. page 17 The “Start/Stop” button was not pressed. Press the “Start/Stop” button.
———————————————————————————————————————————————————— Symptom The upper thread breaks. Probable Cause Remedy Reference The upper thread was not threaded correctly (for example, the spool is not installed correctly, the spool cap is too big for the spool being used, or the thread has come out of the needle bar thread guide). Correct the upper threading. page 28 There are knots or tangles in the thread. Remove any knots or tangles. – The selected needle is not appropriate for the thread being used.
APPENDIX —————————————————————————————————————————————— Symptom The thread tension is incorrect. The fabric is wrinkled. Stitches are skipped. 146 Probable Cause Remedy Reference The upper thread was not threaded correctly. Correct the upper threading. page 28 The bobbin thread is incorrectly installed. Correctly install the bobbin thread. page 26 The combination of fabric, thread and needle is not correct. Select a thread and needle that are appropriate for the type of fabric being sewn.
———————————————————————————————————————————————————— Symptom Probable Cause Remedy Reference Dust has accumulated in the feed dogs or in the bobbin case. Clean the race. page 142 The upper thread was not threaded correctly. Correct the upper threading. page 28 The bobbin case is scratched, or has a burr on it. Replace the bobbin case. Contact your dealer or the nearest authorized service center. A bobbin designed specifically for this machine is not used.
APPENDIX —————————————————————————————————————————————— Error messages If (“Start/Stop” button) is pressed before the sewing machine is correctly set up or if an operation is performed incorrectly, an error message appears in the LCD. Follow the instructions that appear. The message will disappear if (OK key) or Error Message (Cancel/clear key) is pressed while the message is displayed. Probable Cause The selected setting cannot be changed with the selected pattern.
———————————————————————————————————————————————————— Nothing appears in the LCD Cancelling the operation beep If nothing appears in the LCD when the sewing machine is turned on, the brightness of the LCD is either too light or too dark. If this is the case, perform the following operation. When the sewing machine is purchased, it is set to beep each time an operation panel key is pressed. This setting can be changed so that the machine does not beep. a Turn off the sewing machine.
APPENDIX d Press —————————————————————————————————————————————— or (Stitch width keys) to select . To return to keys). , press or (Stitch width X The machine is now set so that it will not beep. e 150 Press (Cancel/clear key) or (OK key). X The initial stitch screen appears again.
———————————————————————————————————————————————————— Index Numerics 1/4 inch quilting foot ......................................................9 1/4 inch quilting foot with guide .....................................9 2-point zigzag stitch ......................................................77 3-point zigzag stitch ......................................................77 A accessories ...................................................................... 8 accessory bag ...............................
APPENDIX —————————————————————————————————————————————— J P joining ........................................................................ 116 joining stitch ...............................................................100 patchwork stitching .....................................................102 pattern length ..............................................................124 pattern size .................................................................122 patterns ...............................
———————————————————————————————————————————————————— starting to sew ...............................................................52 stitch density ...............................................................123 stitch guide foot ....................................................... 9, 67 stitch length .................................................................. 59 stitch length keys .......................................................... 13 stitch mode ......................................
PANTONE 285 Black New_F1_brother_En_cover Operation Manual Computerized Sewing Machine GETTING READY Read before use. SEWING BASICS UTILITY STITCHES Read when additional information is required.
