Network User's Guide
Table Of Contents
- NETWORK USER’S GUIDE
- Definitions of notes
- Compilation and publication notice
- IMPORTANT NOTE
- Table of Contents
- 1 Introduction
- 2 Changing your machine’s network settings
- 3 Configuring your machine for a wireless network
- Overview
- Step by step chart for wireless network configuration
- Confirm your network environment
- Confirm your wireless network setup method
- Configuration using the WPS/AOSS™ control panel menu (Infrastructure mode only) (Recommended)
- Configuration using the machine’s control panel Setup Wizard to configure your wireless network machine
- Configuration using the Brother installer application on the installation CD-ROM to configure your wireless network machine
- Configuration using the PIN Method of Wi-Fi Protected Setup (Infrastructure mode only)
- Configuring your machine for a wireless network (for Infrastructure mode and Ad-hoc mode)
- Using WPS or AOSS™ from the control panel menu to configure your machine for a wireless network
- Using the Setup Wizard from the control panel
- Configuring your machine when the SSID is not broadcast
- Using the Brother automatic installer application on the installation CD-ROM to configure your machine for a wireless network
- Using the PIN Method of Wi-Fi Protected Setup
- 4 Wireless configuration using the Brother installer application
- 5 Control panel setup
- Network menu
- Restoring the network settings to factory default
- Printing the Network Configuration List
- Printing the WLAN Report
- Function table and default factory settings
- 6 Web Based Management
- Overview
- How to configure the machine settings using Web Based Management (web browser)
- Secure Function Lock 2.0
- Changing the Scan to FTP configuration using a web browser
- Changing the Scan to Network configuration using a web browser
- Changing the LDAP configuration using a web browser (MFC-J6910DW only)
- 7 LDAP operation (MFC-J6910DW only)
- 8 Internet fax
- 9 Security features
- 10 Troubleshooting
- Appendix A
- Index
Control panel setup
29
5
IP Address 5
This field displays the current IP address of the machine. If you have chosen a BOOT Method of Static,
enter the IP address that you wish to assign to the machine (check with your network administrator for the IP
address to use). If you have chosen a method other than Static, the machine will attempt to determine its
IP address using the DHCP or BOOTP protocols. The default IP address of your machine will probably be
incompatible with the IP address numbering scheme of your network. We recommend that you contact your
network administrator for an IP address for the network the unit will be connected on.
Subnet Mask 5
This field displays the current subnet mask used by the machine. If you are not using DHCP or BOOTP to
obtain the subnet mask, enter the desired subnet mask. Check with your network administrator for the subnet
mask to use.
Gateway 5
This field displays the current gateway or router address used by the machine. If you are not using DHCP or
BOOTP to obtain the gateway or router address, enter the address you wish to assign. If you do not have a
gateway or router, leave this field blank. Check with your network administrator if you are unsure.
Node Name 5
You can register the machine name on the Network. This name is often referred to as a NetBIOS name; it will
be the name that is registered by the WINS server on your network. Brother recommends the name
BRNxxxxxxxxxxxx for a wired network or BRWxxxxxxxxxxxx for a wireless network (where xxxxxxxxxxxx is
your machine’s Ethernet address) (up to 15 characters).
WINS Config 5
This selection controls how the machine obtains the IP address of the WINS server.
Auto 5
Automatically uses a DHCP request to determine the IP addresses for the primary and secondary WINS
servers. You must set the BOOT Method to Auto or DHCP for this feature to work.
Static
5
Uses a specified IP address for the primary and secondary WINS servers.
WINS Server 5
Primary WINS Server IP Address 5
This field specifies the IP address of the primary WINS (Windows
®
Internet Name Service) server. If set to a
non-zero value, the machine will contact this server to register its name with the Windows
®
Internet Name
Service.