Network User's Guide
Table Of Contents
- NETWORK USER’S GUIDE
- Definitions of notes
- Compilation and publication notice
- IMPORTANT NOTE
- Table of Contents
- 1 Introduction
- 2 Changing your machine’s network settings
- 3 Configuring your machine for a wireless network
- Overview
- Step by step chart for wireless network configuration
- Confirm your network environment
- Confirm your wireless network setup method
- Configuration using the WPS/AOSS™ control panel menu (Infrastructure mode only) (Recommended)
- Configuration using the machine’s control panel Setup Wizard to configure your wireless network machine
- Configuration using the Brother installer application on the installation CD-ROM to configure your wireless network machine
- Configuration using the PIN Method of Wi-Fi Protected Setup (Infrastructure mode only)
- Configuring your machine for a wireless network (for Infrastructure mode and Ad-hoc mode)
- Using WPS or AOSS™ from the control panel menu to configure your machine for a wireless network
- Using the Setup Wizard from the control panel
- Configuring your machine when the SSID is not broadcast
- Using the Brother automatic installer application on the installation CD-ROM to configure your machine for a wireless network
- Using the PIN Method of Wi-Fi Protected Setup
- 4 Wireless configuration using the Brother installer application
- 5 Control panel setup
- Network menu
- Restoring the network settings to factory default
- Printing the Network Configuration List
- Printing the WLAN Report
- Function table and default factory settings
- 6 Web Based Management
- Overview
- How to configure the machine settings using Web Based Management (web browser)
- Secure Function Lock 2.0
- Changing the Scan to FTP configuration using a web browser
- Changing the Scan to Network configuration using a web browser
- Changing the LDAP configuration using a web browser (MFC-J6910DW only)
- 7 LDAP operation (MFC-J6910DW only)
- 8 Internet fax
- 9 Security features
- 10 Troubleshooting
- Appendix A
- Index
Configuring your machine for a wireless network
19
3
h Enter the SSID name. (For information how to enter text, see the Quick Setup Guide.)
Press OK.
i Press Ad-hoc or Infrastructure when instructed.
Do one of the following:
If you chose Ad-hoc, go to step k.
If you chose Infrastructure, go to step j.
j Choose and press the Authentication method.
Do one of the following:
If you chose Open System, go to step k.
If you chose Shared Key, go to step l.
If you chose WPA/WPA2-PSK, go to step m.
k Choose and press the Encryption type None or WEP.
Do one of the following:
If you chose None, go to step o.
If you chose WEP, go to step l.
l Enter the WEP key you wrote down in step a on page 18. Press OK. Go to step o. (For information how
to enter text, see the Quick Setup Guide.)
m Choose and press the Encryption type, TKIP or AES. Go to step n.
n Enter the WPA key you wrote down in step a on page 18 and press OK. Go to step o. (For information
how to enter text, see the Quick Setup Guide.)
o To apply the settings, press Yes. To cancel, press No.
Do one of the following:
If you chose Yes, go to step p.
If you chose No, go back to step g.
p The machine starts to connect to the wireless device you have chosen.
q A connection result message appears for 60 seconds on the LCD and a wireless LAN report will
automatically be printed. If the connection failed, check the error code on the printed report and refer to
Troubleshooting in the Quick Setup Guide.
(Windows
®
)
You have completed the wireless network setup. If you would like to continue installing drivers
and software necessary for operating your device, please choose
Initial Installation/Install MFL-Pro Suite from the installation CD-ROM menu.
(Macintosh)
You have completed the wireless network setup. If you would like to continue installing drivers
and software necessary for operating your device, please double-click Start Here OSX in the
installation CD-ROM.